scholarly journals Assessment of Breathing Parameters Using an Inertial Measurement Unit (IMU)-Based System

Sensors ◽  
2018 ◽  
Vol 19 (1) ◽  
pp. 88 ◽  
Author(s):  
Ambra Cesareo ◽  
Ylenia Previtali ◽  
Emilia Biffi ◽  
Andrea Aliverti
Keyword(s):  
Inertial Sensors ◽  
Low Cost ◽  
Estimation Error ◽  
Processing Algorithm ◽  
Measurement Unit ◽  
Breathing Patterns ◽  
Independent Manner ◽  
Inertial Measurement ◽  
Optoelectronic Plethysmography ◽  
The One

Breathing frequency (fB) is an important vital sign that—if appropriately monitored—may help to predict clinical adverse events. Inertial sensors open the door to the development of low-cost, wearable, and easy-to-use breathing-monitoring systems. The present paper proposes a new posture-independent processing algorithm for breath-by-breath extraction of breathing temporal parameters from chest-wall inclination change signals measured using inertial measurement units. An important step of the processing algorithm is dimension reduction (DR) that allows the extraction of a single respiratory signal starting from 4-component quaternion data. Three different DR methods are proposed and compared in terms of accuracy of breathing temporal parameter estimation, in a group of healthy subjects, considering different breathing patterns and different postures; optoelectronic plethysmography was used as reference system. In this study, we found that the method based on PCA-fusion of the four quaternion components provided the best fB estimation performance in terms of mean absolute errors (<2 breaths/min), correlation (r > 0.963) and Bland–Altman Analysis, outperforming the other two methods, based on the selection of a single quaternion component, identified on the basis of spectral analysis; particularly, in supine position, results provided by PCA-based method were even better than those obtained with the ideal quaternion component, determined a posteriori as the one providing the minimum estimation error. The proposed algorithm and system were able to successfully reconstruct the respiration-induced movement, and to accurately determine the respiratory rate in an automatic, position-independent manner.

scholarly journals Feasibility Study of Multi Inertial Measurement Unit

Proceedings ◽  
2019 ◽  
Vol 42 (1) ◽  
pp. 74 ◽  
Author(s):  
Ariel Larey ◽  
Eliel Aknin ◽  
Itzik Klein
Keyword(s):  
Inertial Measurement Unit ◽  
Inertial Sensors ◽  
Low Cost ◽  
Software Tool ◽  
Experimental Results ◽  
Measurement Unit ◽  
Outlier Rejection ◽  
Inertial Measurement ◽  
Navigation Solution ◽  
Sensory Data

An inertial measurement unit (IMU) typically has three accelerometers and three gyroscopes. The output of those inertial sensors is used by an inertial navigation system to calculate the navigation solution–position, velocity and attitude. Since the sensor measurements contain noise, the navigation solution drifts over time. When considering low cost sensors, multiple IMUs can be used to improve the performance of a single unit. In this paper, we describe our designed 32 multi-IMU (MIMU) architecture and present experimental results using this system. To analyze the sensory data, a dedicated software tool, capable of addressing MIMUs inputs, was developed. Using the MIMU hardware and software tool we examined and evaluated the MIMUs for: (1) navigation solution accuracy (2) sensor outlier rejection (3) stationary calibration performance (4) coarse alignment accuracy and (5) the effect of different MIMUs locations in the architecture. Our experimental results show that 32 IMUs obtained better performance than a single IMU for all testcases examined. In addition, we show that performance was improved gradually as the number of IMUs was increased in the architecture.

Wireless Input Technology Based on MEMS Inertial Measurement Unit - A Survey

2017 ◽  
Vol 870 ◽  
pp. 79-84
Author(s):  
Zhen Xian Fu ◽  
Guang Ying Zhang ◽  
Yu Rong Lin ◽  
Yang Liu
Keyword(s):  
Inertial Measurement Unit ◽  
Inertial Sensors ◽  
Inertial Sensor ◽  
Low Cost ◽  
Propagation Model ◽  
Measurement Unit ◽  
Input Device ◽  
Operational Environment ◽  
Inertial Measurement ◽  
Mems Imu

Rapid progress in Micro-Electromechanical System (MEMS) technique is making inertial sensors increasingly miniaturized, enabling it to be widely applied in people’s everyday life. Recent years, research and development of wireless input device based on MEMS inertial measurement unit (IMU) is receiving more and more attention. In this paper, a survey is made of the recent research on inertial pens based on MEMS-IMU. First, the advantage of IMU-based input is discussed, with comparison with other types of input systems. Then, based on the operation of an inertial pen, which can be roughly divided into four stages: motion sensing, error containment, feature extraction and recognition, various approaches employed to address the challenges facing each stage are introduced. Finally, while discussing the future prospect of the IMU-based input systems, it is suggested that the methods of autonomous and portable calibration of inertial sensor errors be further explored. The low-cost feature of an inertial pen makes it desirable that its calibration be carried out independently, rapidly, and portably. Meanwhile, some unique features of the operational environment of an inertial pen make it possible to simplify its error propagation model and expedite its calibration, making the technique more practically viable.

scholarly journals Inertial Measurement Unit Sensors in Assistive Technologies for Visually Impaired People, a Review

Sensors ◽  
2021 ◽  
Vol 21 (14) ◽  
pp. 4767
Author(s):  
Karla Miriam Reyes Leiva ◽  
Milagros Jaén-Vargas ◽  
Benito Codina ◽  
José Javier Serrano Olmedo
Keyword(s):  
Inertial Measurement Unit ◽  
Visually Impaired ◽  
Inertial Sensors ◽  
Assistive Technologies ◽  
Biomechanical Analysis ◽  
Measurement Unit ◽  
Inertial Measurement ◽  
Visually Impaired People ◽  
Impaired People ◽  
Application Fields

A diverse array of assistive technologies have been developed to help Visually Impaired People (VIP) face many basic daily autonomy challenges. Inertial measurement unit sensors, on the other hand, have been used for navigation, guidance, and localization but especially for full body motion tracking due to their low cost and miniaturization, which have allowed the estimation of kinematic parameters and biomechanical analysis for different field of applications. The aim of this work was to present a comprehensive approach of assistive technologies for VIP that include inertial sensors as input, producing results on the comprehension of technical characteristics of the inertial sensors, the methodologies applied, and their specific role in each developed system. The results show that there are just a few inertial sensor-based systems. However, these sensors provide essential information when combined with optical sensors and radio signals for navigation and special application fields. The discussion includes new avenues of research, missing elements, and usability analysis, since a limitation evidenced in the selected articles is the lack of user-centered designs. Finally, regarding application fields, it has been highlighted that a gap exists in the literature regarding aids for rehabilitation and biomechanical analysis of VIP. Most of the findings are focused on navigation and obstacle detection, and this should be considered for future applications.

Systematic Calibration Method for FOG Inertial Measurement Units

2013 ◽  
Vol 662 ◽  
pp. 717-720 ◽  
Author(s):  
Zhen Yu Zheng ◽  
Yan Bin Gao ◽  
Kun Peng He
Keyword(s):  
Inertial Measurement Unit ◽  
Inertial Sensors ◽  
Calibration Method ◽  
State Equation ◽  
Measurement Unit ◽  
Observation System ◽  
Body Frame ◽  
Inertial Measurement ◽  
Measurement Units ◽  
Error Coefficients

As an inertial sensors assembly, the FOG inertial measurement unit (FIMU) must be calibrated before being used. The paper presents a one-time systematic IMU calibration method only using two-axis low precision turntable. First, the detail error model of inertial sensors using defined body frame is established. Then, only velocity taken as observation, system 33 state equation is established including the lever arm effects and nonlinear terms of scale factor error. The turntable experiments verify that the method can identify all the error coefficients of FIMU on low-precision two-axis turntable, after calibration the accuracy of navigation is improved.

scholarly journals Feedforward ins aiding: an investigation of maneuvers for in-flight alignment

2007 ◽  
Vol 18 (4) ◽  
pp. 459-470 ◽  
Author(s):  
Jacques Waldmann
Keyword(s):  
Autonomous Vehicles ◽  
Inertial Sensors ◽  
Low Cost ◽  
Measurement Unit ◽  
Model Mismatch ◽  
External Data ◽  
Rate Gyro ◽  
External Position ◽  
The Impact ◽  
Gyro Drift

Navigation in autonomous vehicles involves integrating measurements from on-board inertial sensors and external data collected by various sensors. In this paper, the computer-frame velocity error model is augmented with a random constant model of accelerometer bias and rate-gyro drift for use in a Kalman filter-based fusion of a low-cost rotating inertial navigation system (INS) with external position and velocity measurements. The impact of model mismatch and maneuvers on the estimation of misalignment and inertial measurement unit (IMU) error is investigated. Previously, the literature focused on analyzing the stripped observability matrix that results from applying piece-wise constant acceleration segments to a stabilized, gimbaled INS to determine the accuracy of misalignment, accelerometer bias, and rate-gyro drift estimation. However, its validation via covariance analysis neglected model mismatch. Here, a vertically undamped, three channel INS with a rotating IMU with respect to the host vehicle is simulated. Such IMU rotation does not require the accurate mechanism of a gimbaled INS (GINS) and obviates the need to maneuver away from the desired trajectory during in-flight alignment (IFA) with a strapdown IMU. In comparison with a stationary GINS at a known location, IMU rotation enhances estimation of accelerometer bias, and partially improves estimation of rate-gyro drift and misalignment. Finally, combining IMU rotation with distinct acceleration segments yields full observability, thus significantly enhancing estimation of rate-gyro drift and misalignment.

Maximum Correntropy Kalman Filter for Orientation Estimation With Application to LiDAR Inertial Odometry

2020 ◽  
Author(s):  
Seyed Fakoorian ◽  
Matteo Palieri ◽  
Angel Santamaria-Navarro ◽  
Cataldo Guaragnella ◽  
Dan Simon ◽  
...  
Keyword(s):  
Kalman Filtering ◽  
Inertial Measurement Unit ◽  
Low Cost ◽  
Attitude Estimation ◽  
High Rate ◽  
Measurement Unit ◽  
Orientation Estimation ◽  
Localization Accuracy ◽  
Inertial Measurement ◽  
Robotic Applications

Abstract Accurate attitude estimation using low-cost sensors is an important capability to enable many robotic applications. In this paper, we present a method based on the concept of correntropy in Kalman filtering to estimate the 3D orientation of a rigid body using a low-cost inertial measurement unit (IMU). We then leverage the proposed attitude estimation framework to develop a LiDAR-Intertial Odometry (LIO) demonstrating improved localization accuracy with respect to traditional methods. This is of particular importance when the robot undergoes high-rate motions that typically exacerbate the issues associated with low-cost sensors. The proposed orientation estimation approach is first validated using the data coming from a low-cost IMU sensor. We further demonstrate the performance of the proposed LIO solution in a simulated robotic cave exploration scenario.

An inertial measurement unit tracking system for body movement in comparison with optical tracking

2020 ◽  
Vol 234 (7) ◽  
pp. 728-737
Author(s):  
Rui Li ◽  
Barclay Jumet ◽  
Hongliang Ren ◽  
WenZhan Song ◽  
Zion Tsz Ho Tse
Keyword(s):  
Inertial Measurement Unit ◽  
Tracking System ◽  
Low Cost ◽  
Optical Tracking ◽  
Measurement Unit ◽  
Joint Movement ◽  
Joint Angles ◽  
Optical Tracking System ◽  
Microelectromechanical System ◽  
Inertial Measurement

The recent advancement of motion tracking technology offers better treatment tools for conditions, such as movement disorders, as the outcome of the rehabilitation could be quantitatively defined. The accurate and fast angular information output of the inertial measurement unit tracking systems enables the collection of accurate kinematic data for clinical assessment. This article presents a study of a low-cost microelectromechanical system inertial measurement unit-based tracking system in comparison with the conventional optical tracking system. The system consists of seven microelectromechanical system inertial measurement units, which could be mounted on the lower limbs of the subjects. For the feasibility test, 10 human participants were instructed to perform three different motions: walking, running, and fencing lunges when wearing specially designed sleeves. The subjects’ lower body movements were tracked using our inertial measurement unit-based system and compared with the gold standard—the NDI Polaris Vega optical tracking system. The results of the angular comparison between the inertial measurement unit and the NDI Polaris Vega optical tracking system were as follows: the average cross-correlation value was 0.85, the mean difference of joint angles was 2.00°, and the standard deviation of joint angles was ± 2.65°. The developed microelectromechanical system–based tracking system provides an alternative low-cost solution to track joint movement. Moreover, it is able to operate on an Android platform and could potentially be used to assist outdoor or home-based rehabilitation.

The Correcting Approach of Gyroscope-Free Inertial Navigation Based on the Applicable Topological Map

2019 ◽  
Vol 19 (2) ◽  
Author(s):  
Mehdi Dehghani ◽  
Hamed Kharrati ◽  
Hadi Seyedarabi ◽  
Mahdi Baradarannia
Keyword(s):  
Mobile Robot ◽  
Mobile Robots ◽  
Inertial Sensors ◽  
Low Cost ◽  
Measurement Unit ◽  
Sensor Calibration ◽  
Topological Map ◽  
Stereo Cameras ◽  
Long Time ◽  
Navigation Errors

The accumulated error and noise sensitivity are the two common problems of ordinary inertial sensors. An accurate gyroscope is too expensive, which is not normally applicable in low-cost missions of mobile robots. Since the accelerometers are rather cheaper than similar types of gyroscopes, using redundant accelerometers could be considered as an alternative. This mechanism is called gyroscope-free navigation. The article deals with autonomous mobile robot (AMR) navigation based on gyroscope-free method. In this research, the navigation errors of the gyroscope-free method in long-time missions are demonstrated. To compensate the position error, the aid information of low-cost stereo cameras and a topological map of the workspace are employed in the navigation system. After precise sensor calibration, an amendment algorithm is presented to fuse the measurement of gyroscope-free inertial measurement unit (GFIMU) and stereo camera observations. The advantages and comparisons of vision aid navigation and gyroscope-free navigation of mobile robots will be also discussed. The experimental results show the increasing accuracy in vision-aid navigation of mobile robot.

Sign in / Sign up

Export Citation Format

Share Document