scholarly journals Fiber Fabry-Perot Force Sensor with Small Volume and High Performance for Assessing Fretting Damage of Steam Generator Tubes

Sensors ◽  
2017 ◽  
Vol 17 (12) ◽  
pp. 2899 ◽  
Author(s):  
Peijian Huang ◽  
Ning Wang ◽  
Junying Li ◽  
Yong Zhu ◽  
Jie Zhang
Keyword(s):  
Steam Generator ◽  
High Performance ◽  
Small Volume ◽  
Force Sensor ◽  
Fabry Perot ◽  
Fretting Damage ◽  
Steam Generator Tubes

scholarly journals Optical Fiber Demodulation System with High Performance for Assessing Fretting Damage of Steam Generator Tubes

Sensors ◽  
2018 ◽  
Vol 18 (2) ◽  
pp. 201 ◽  
Author(s):  
Peijian Huang ◽  
Ning Wang ◽  
Junying Li ◽  
Yong Zhu ◽  
Jie Zhang ◽  
...  
Keyword(s):  
Optical Fiber ◽  
Steam Generator ◽  
High Performance ◽  
Fretting Damage ◽  
Steam Generator Tubes

Parametric Study of External Pressure on Steam Generator Tube Bends

2012 ◽  
Author(s):  
Mitch Hokazono ◽  
Clayton T. Smith
Keyword(s):  
Steam Generator ◽  
Parametric Study ◽  
External Pressure ◽  
Light Water Reactor ◽  
Material Strength ◽  
Steam Generators ◽  
Elliptical Cross ◽  
Light Water ◽  
Water Reactor ◽  
Steam Generator Tubes

Integral light-water reactor designs propose the use of steam generators located within the reactor vessel. Steam generator tubes in these designs must withstand external pressure loadings to prevent buckling, which is affected by material strength, fabrication techniques, chemical environment and tube geometry. Experience with fired tube boilers has shown that buckling in boiler tubes is greatly alleviated by controlling ovality in bends when the tubes are fabricated. Light water reactor steam generator pressures will not cause a buckling problem in steam generators with reasonable fabrication limits on tube ovality and wall thinning. Utilizing existing Code rules, there is a significant design margin, even for the maximum differential pressure case. With reasonable bend design and fabrication limits the helical steam generator thermodynamic advantages can be realized without a buckling concern. This paper describes a theoretical methodology for determining allowable external pressure for steam generator tubes subject to tube ovality based on ASME Section III Code Case N-759-2 rules. A parametric study of the results of this methodology applied to an elliptical cross section with varying wall thicknesses, tube diameters, and ovality values is also presented.

Construction and alignment of a high performance multipass vernier tandem Fabry–Perot interferometer

1981 ◽  
Vol 52 (10) ◽  
pp. 1478-1486 ◽  
Author(s):  
S. M. Lindsay ◽  
M. W. Anderson ◽  
J. R. Sandercock
Keyword(s):  
High Performance ◽  
Fabry Perot

Evaluation of Motorized Rotating Pancake Coil Probe Signals Simulated by Numerical Analysis in Steam Generator Tubes

2006 ◽  
Vol 321-323 ◽  
pp. 451-454
Author(s):  
Joo Young Yoo ◽  
Sung Jin Song ◽  
Chang Hwan Kim ◽  
Hee Jun Jung ◽  
Young Hwan Choi ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Numerical Analysis ◽  
Steam Generator ◽  
Integral Method ◽  
Volume Integral ◽  
Analysis Software ◽  
Steam Generator Tubes ◽  
Calibration Tool ◽  
High Possibility ◽  
Good Agreement

In the present study, the synthetic signals from the combo tube are simulated by using commercial electromagnetic numerical analysis software which has been developed based on a volume integral method. A comparison of the simulated signals to the experiments is made for the verification of accuracy, and then evaluation of five deliberated single circumferential indication signals is performed to explore a possibility of using a numerical simulation as a practical calibration tool. The good agreement between the evaluation results for two cases (calibration done by experiments and calibration made by simulation) demonstrates such a high possibility.

Sine-Wave Exciting Circuit for Quartz Vibrating Gyroscope

2013 ◽  
Vol 562-565 ◽  
pp. 417-420
Author(s):  
Qing Yi Wang ◽  
Xiao Wei Liu ◽  
Rui Zhang ◽  
Liang Yin ◽  
Zhi Ping Zhou
Keyword(s):  
High Performance ◽  
Small Volume ◽  
Angular Rate ◽  
Sine Wave ◽  
Processing Technology ◽  
Angular Rate Sensor ◽  
Square Wave ◽  
Rate Sensor ◽  
Is Design ◽  
Cmos Processing

Quartz vibrating gyroscope is a kind of angular rate sensor which is the compromise between the high performance and the small volume. Improvement of the performance is a focus of reach. In this paper, a sine-wave exciting method is discussed. A sine-wave exciting circuit is design and processed with 0.5μm CMOS processing technology. During comparing the sine-wave exciting response and the square-wave one, the sine-wave exciting circuit is more beneficial to improve the performance of the quartz vibrating gyroscope.

Evaluation of the Creep Rupture Behavior of Alloy 690 Steam Generator Tubes Considering the Pressure Ramp Rate

2021 ◽  
Author(s):  
Jongmin Kim ◽  
Min-Chul Kim ◽  
Joonyeop Kwon
Keyword(s):  
Steam Generator ◽  
Creep Rupture ◽  
Parameter Method ◽  
Alloy 600 ◽  
Steam Generator Tube ◽  
Failure Pressure ◽  
Alloy 690 ◽  
Rupture Model ◽  
Temperature And Pressure ◽  
Steam Generator Tubes

Abstract The materials used previously for steam generator tubes around the world have been replaced and will be replaced by Alloy 690 given its improved corrosion resistance relative to that of Alloy 600. However, studies of the high- temperature creep and creep-rupture characteristics of steam generator tubes made of Alloy 690 are insufficient compared to those focusing on Alloy 600. In this study, several creep tests were conducted using half tube shape specimens of the Alloy 690 material at temperatures ranging from 650 to 850C and stresses in the range of 30 to 350 MPa, with failure times to creep rupture ranging from 3 to 870 hours. Based on the creep test results, creep life predictions were then made using the well-known Larson Miller Parameter method. Steam generator tube rupture tests were also conducted under the conditions of a constant temperature and pressure ramp using steam generator tube specimens. The rupture test equipment was designed and manufactured to simulate the transient state (rapid temperature and pressure changes) in the event of a severe accident condition. After the rupture test, the damage to the steam generator tubes was predicted using a creep rupture model and a flow stress model. A modified creep rupture model for Alloy 690 steam generator tube material is proposed based on the experimental results. A correction factor of 1.7 in the modified creep rupture model was derived for the Alloy 690 material. The predicted failure pressure was in good agreement with the experimental failure pressure.

Sign in / Sign up

Export Citation Format

Share Document