scholarly journals A Micro Bubble Structure Based Fabry–Perot Optical Fiber Strain Sensor with High Sensitivity and Low-Cost Characteristics

Sensors ◽  
2017 ◽  
Vol 17 (3) ◽  
pp. 555 ◽  
Author(s):  
Lu Yan ◽  
Zhiguo Gui ◽  
Guanjun Wang ◽  
Yongquan An ◽  
Jinyu Gu ◽  
...  
Keyword(s):  
Low Cost ◽  
Strain Sensor ◽  
Glass Tube ◽  
High Sensitivity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Fabry Perot ◽  
Micro Bubble ◽  
Bubble Structure ◽  
Cost Characteristics

A high-sensitivity, low-cost, ultrathin, hollow fiber micro bubble structure was proposed; such a bubble can be used to develop a high-sensitivity strain sensor based on a Fabry–Perot interferometer (FPI). The micro bubble is fabricated at the fiber tip by splicing a glass tube to a single mode fiber (SMF) and then the glass tube is filled with gas in order to expand and form a micro bubble. The sensitivity of the strain sensor with a cavity length of about 155 μm and a bubble wall thickness of about 6 μm was measured to be up to 8.14 pm/μϵ.

scholarly journals Correction: Yan, L., et al. A Micro Bubble Structure Based Fabry–Perot Optical Fiber Strain Sensor with High Sensitivity and Low-Cost Characteristics Sensors, 2017, 17, 555.

Sensors ◽  
2018 ◽  
Vol 18 (9) ◽  
pp. 3102
Author(s):  
Lu Yan ◽  
Zhiguo Gui ◽  
Guanjun Wang ◽  
Yongquan An ◽  
Jinyu Gu ◽  
...  
Keyword(s):  
Optical Fiber ◽  
Low Cost ◽  
Strain Sensor ◽  
High Sensitivity ◽  
Correct Figure ◽  
Fabry Perot ◽  
Micro Bubble ◽  
Bubble Structure ◽  
Cost Characteristics

An correction is presented to correct Figure 5a in [Sensors, 2017, 17, 555].

scholarly journals An Optical Fiber Fabry–Perot Pressure Sensor with Optimized Thin Microbubble Film Shaping for Sensitivity Enhancement

Coatings ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 358 ◽  
Author(s):  
Shubin Zhang ◽  
Zhenjun Shao ◽  
Jinrong Liu ◽  
Meixue Zong ◽  
Jian Shen ◽  
...  
Keyword(s):  
Thin Film ◽  
Arc Discharge ◽  
Structural Parameters ◽  
Silicon Film ◽  
Glass Tube ◽  
High Sensitivity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Fabry Perot ◽  
Micrometer Scale

A pressure-assisted arc discharge method of preparing silicon microbubbles with a glass tube was utilized for decreasing the bubble film’s thickness and improving the bubble’s uniformity. By controlling the arc discharge intensity, discharge time and the position of the fiber carefully, the thickness of the microbubble film was reduced to the micrometer scale. Later, the thin film of the microbubble was transferred to the end the single-mode-fiber/glass-tube structure, for forming the FP (Fabry–Perot) interference cavity. As the thin film is sensitive to the outer pressure, such a configuration could be used for a high-sensitive-pressure measurement. Experimental results show that the sensitivity of this FP (Fabry–Perot) cavity was 6790 pm/MPa when the outer pressure ranges from 100 to 1600 kPa, and the relationship between the structural parameters of the thin film and the outer pressure was theoretically analyzed. Moreover, this special structure made of the end silicon film microbubble is more suitable for high-sensitivity applications.

scholarly journals A High Sensitivity Temperature Sensing Probe Based on Microfiber Fabry-Perot Interference

Sensors ◽  
2019 ◽  
Vol 19 (8) ◽  
pp. 1819 ◽  
Author(s):  
Zhoubing Li ◽  
Yue Zhang ◽  
Chunqiao Ren ◽  
Zhengqi Sui ◽  
Jin Li
Keyword(s):  
Low Cost ◽  
High Sensitivity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Temperature Sensing ◽  
Compact Structure ◽  
Fabry Perot ◽  
Temperature Monitor ◽  
Core Fiber ◽  
Fitting In

In this paper, a miniature Fabry-Perot temperature probe was designed by using polydimethylsiloxane (PDMS) to encapsulate a microfiber in one cut of hollow core fiber (HCF). The microfiber tip and a common single mode fiber (SMF) end were used as the two reflectors of the Fabry-Perot interferometer. The temperature sensing performance was experimentally demonstrated with a sensitivity of 11.86 nm/°C and an excellent linear fitting in the range of 43–50 °C. This high sensitivity depends on the large thermal-expansion coefficient of PDMS. This temperature sensor can operate no higher than 200 °C limiting by the physicochemical properties of PDMS. The low cost, fast fabrication process, compact structure and outstanding resolution of less than 10−4 °C enable it being as a promising candidate for exploring the temperature monitor or controller with ultra-high sensitivity and precision.

Experimental Research of Strain and Temperature Based on EFPI Sensor

2011 ◽  
Vol 130-134 ◽  
pp. 4185-4188
Author(s):  
Xiu Feng Yang ◽  
Chun Yu Zhang ◽  
Zheng Rong Tong
Keyword(s):  
Low Cost ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Good Reliability ◽  
High Repetition ◽  
Sensing Applications ◽  
Fabry Perot ◽  
Wet Chemical ◽  
The Many ◽  
Multi Mode

An extrinsic Fabry-Perot (F-P) interferometric (EFPI) sensor by using simple etching and fusing method is proposed and demonstrated. The cavity is formed by wet chemical etching of multi-mode fiber (MMF) end face in hydrofluoric acid solutions, and then it is fused to the end of a single-mode fiber (SMF) to form an extrinsic F-P structure. The strain and temperature of EFPI sensor are studied experimentally. The experimental results show that the interference wavelength becomes 2.648nm longer while the strain increases from 0N to 637N, and the strain sensitivity is about 0.004nm/N, and linearity is 0.999. The interference wavelength becomes 0.032nm shorter while the temperature increases from 20°C to 100°C. This kind of sensor has the many advantages of easy fabrication, good reliability, high-repetition, small size, low cost and mass-production, which offers great prospect for sensing applications.

scholarly journals Cascaded-Cavity Fabry-Perot Interferometric Gas Pressure Sensor based on Vernier Effect

Sensors ◽  
2018 ◽  
Vol 18 (11) ◽  
pp. 3677 ◽  
Author(s):  
Peng Chen ◽  
Yutang Dai ◽  
Dongsheng Zhang ◽  
Xiaoyan Wen ◽  
Minghong Yang
Keyword(s):  
Capillary Tube ◽  
High Sensitivity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Gas Pressure ◽  
Glass Capillary ◽  
Compact Structure ◽  
Fabry Perot ◽  
Fs Laser ◽  
Vernier Effect

An extrinsic Fabry-Perot interferometer (EFPI) composed of double fiber FP cavities in a glass capillary tube to generate Vernier effect has been fabricated and employed for gas pressure sensing. A lead-in single-mode fiber (LSMF) and a reflective single-mode fiber (RSMF) were inserted into the capillary tube to form a FP cavity. Femtosecond (fs) laser was used to ablate openings on a capillary tube for gas passage to the FP cavity. A fusion hole was also drilled on the end face of a SMF by fs laser. The sensitivity of the sensor is enhanced due to Vernier effect. Experimental results show that the sensitivity was as high as 86.64 nm/MPa in the range of 0~0.6 MPa, which is 32.8 times larger than that of an open-cavity EFPI sensor without Vernier effect. The temperature cross-sensitivity of the sensor was measured to be about 5.18 KPa/°C. The proposed sensor was characterized by its high sensitivity, compact structure and ease of fabrication, and would have extensive application prospects in gas sensing fields.

scholarly journals A High Precision Fiber Optic Fabry–Perot Pressure Sensor Based on AB Epoxy Adhesive Film

Photonics ◽  
2021 ◽  
Vol 8 (12) ◽  
pp. 581
Author(s):  
Yanan Zhang ◽  
Shubin Zhang ◽  
Haitao Gao ◽  
Danping Xu ◽  
Zhuozhen Gao ◽  
...  
Keyword(s):  
Pressure Sensor ◽  
High Sensitivity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Epoxy Adhesive ◽  
Curing Time ◽  
Adhesive Film ◽  
Interference Spectrum ◽  
Fabry Perot ◽  
Potential Applications

This paper proposes a Fabry–Perot pressure sensor based on AB epoxy adhesive with ultra-high sensitivity under low pressure. Fabry–Perot interference, located between single-mode fiber (SMF) and hollow-core fiber (HCF), is an ultra-thin AB epoxy film formed by capillary action. Then the thick HCF was used to fix the HCF and SMF at both ends with AB epoxy adhesive. Experimental results show that when the thickness of AB epoxy film is 8.74 μm, and the cavity length is 30 μm, the sensor has the highest sensitivity. The sensitivity is 257.79 nm/MPa within the pressure range of 0–70 kPa. It also investigated the influence of the curing time of AB epoxy on the interference spectrum. Experiments showed that the interference spectrum peak is blue-shifted with the increase of curing time. Our study also demonstrated the humidity stability of this pressure sensor. These characteristics mean that our sensor has potential applications in the biomedical field and ocean exploration.

scholarly journals A Compact Strain Sensor Based on Microstructural Fabry-Perot Fiber Cavity

2021 ◽  
Author(s):  
Zhiwu Guo ◽  
Yannan Wang ◽  
Jin Li
Keyword(s):  
Low Cost ◽  
Strain Sensor ◽  
Single Mode ◽  
Expansion Method ◽  
Drawing Process ◽  
Fiber System ◽  
Air Chamber ◽  
Fabry Perot ◽  
The Common ◽  
Easy Integration

Fabry-Perot air chamber was constructed at the melting point (splicing location) of two single-mode fibers by glycerin assisted self-expansion method. The morphology of the Fabry-Perot air chamber was fabricated and optimized by modulating the splicing parameters (drawing process, discharging location, time and intensity) and the fibers’ end-face (plane or arc). The in-line or reflected Fabry-Perot cavities have been applied to determine the tensile strain in the range of 0-1.2 N. The train sensing performance of the spherical shaped FP cavity has been experimentally demonstrated with the best sensitivity of 3.628 nm/N, corresponding to the resolution of ~0.005 N. The proposed FP fiber sensor has the advantages of low cost, fast fabrication and easy-integration with the common fiber system.

scholarly journals All Single-Mode-Fiber Supercontinuum Source Setup for Monitoring of Multiple Gases Applications

Sensors ◽  
2020 ◽  
Vol 20 (11) ◽  
pp. 3239
Author(s):  
Javier A. Martin-Vela ◽  
Eloisa Gallegos-Arellano ◽  
Juan M. Sierra-Hernández ◽  
Julián M. Estudillo-Ayala ◽  
Daniel Jauregui-Vázquez ◽  
...  
Keyword(s):  
Gas Sensing ◽  
Low Cost ◽  
High Sensitivity ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Experimental Results ◽  
Hitran Database ◽  
Broadband Absorption ◽  
Sensing System ◽  
Absorption Technique

In this paper, a gas sensing system based on a conventional absorption technique using a single-mode-fiber supercontinuum source (SMF-SC) is presented. The SC source was implemented by channeling pulses from a microchip laser into a one kilometer long single-mode fiber (SMF), obtaining a flat high-spectrum with a bandwidth of up to 350 nm in the region from 1350 to 1700 nm, and high stability in power and wavelength. The supercontinuum radiation was used for simultaneously sensing water vapor and acetylene gas in the regions from 1350 to 1420 nm and 1510 to 1540 nm, respectively. The experimental results show that the absorption peaks of acetylene have a maximum depth of approximately 30 dB and contain about 60 strong lines in the R and P branches, demonstrating a high sensitivity of the sensing setup to acetylene. Finally, to verify the experimental results, the experimental spectra are compared to simulations obtained from the Hitran database. This shows that the implemented system can be used to develop sensors for applications in broadband absorption spectroscopy and as a low-cost absorption spectrophotometer of multiple gases.

Dual Fabry–Pérot Interferometric Carbon Monoxide Sensor Based on the PANI/Co3O4 Sensitive Membrane-Coated Fibre Tip

2019 ◽  
Vol 74 (2) ◽  
pp. 101-107 ◽  
Author(s):  
Jin Peng ◽  
Wenlin Feng ◽  
Xiaozhan Yang ◽  
Guojia Huang ◽  
Shaodian Liu
Keyword(s):  
Carbon Monoxide ◽  
Low Cost ◽  
High Sensitivity ◽  
Single Mode ◽  
Photonic Crystal Fibre ◽  
Single Mode Fibre ◽  
Fabry Perot ◽  
Response And Recovery ◽  
Sensing Membrane ◽  
Mode Fibre

AbstractA novel dual Fabry–Pérot (F-P) interferometric carbon monoxide gas sensor based on polyaniline/Co3O4 (PANI/Co3O4) sensing film coated on the optical fibre end face is proposed and fabricated. Its structure is composed of standard single-mode-fibre (SMF), endlessly photonic crystal fibre (EPCF), and PANI/Co3O4 sensing membrane (PCSM). Therefore, they form three F-P reflectors, the reflector between SMF and EPCF, that between EPCF and PCSM, and interface between PCSM and air. So, the dual F-P interferometer is achieved. The results show that in the range of 0–70 ppm, the interference spectra appear red shift with the increasing carbon monoxide concentration. In addition, the high sensitivity of 21.61 pm/ppm, the excellent linear relationship (R2 = 0.98476), and high selectivity for carbon monoxide are achieved. The response and recovery time are 35 and 84 s, respectively. The sensor has the advantages of high sensitivity, strong selectivity, low cost, and simple structure and is suitable for sensitive detection of trace carbon monoxide gas.

Sign in / Sign up

Export Citation Format

Share Document