scholarly journals Sharpening the Sentinel-2 10 and 20 m Bands to Planetscope-0 3 m Resolution

2020 ◽  
Vol 12 (15) ◽  
pp. 2406 ◽  
Author(s):  
Zhongbin Li ◽  
Hankui K. Zhang ◽  
David P. Roy ◽  
Lin Yan ◽  
Haiyan Huang
Keyword(s):  
Land Surface ◽  
Large Scale ◽  
Near Infrared ◽  
Detailed Examination ◽  
Modulation Transfer ◽  
Computationally Efficient ◽  
Red Edge ◽  
Shortwave Infrared ◽  
Sentinel 2 ◽  
Surface Changes

Combination of near daily 3 m red, green, blue, and near infrared (NIR) Planetscope reflectance with lower temporal resolution 10 m and 20 m red, green, blue, NIR, red-edge, and shortwave infrared (SWIR) Sentinel-2 reflectance provides potential for improved global monitoring. Sharpening the Sentinel-2 reflectance with the Planetscope reflectance may enable near-daily 3 m monitoring in the visible, red-edge, NIR, and SWIR. However, there are two major issues, namely the different and spectrally nonoverlapping bands between the two sensors and surface changes that may occur in the period between the different sensor acquisitions. They are examined in this study that considers Sentinel-2 and Planetscope imagery acquired one day apart over three sites where land surface changes due to biomass burning occurred. Two well-established sharpening methods, high pass modulation (HPM) and Model 3 (M3), were used as they are multiresolution analysis methods that preserve the spectral properties of the low spatial resolution Sentinel-2 imagery (that are better radiometrically calibrated than Planetscope) and are relatively computationally efficient so that they can be applied at large scale. The Sentinel-2 point spread function (PSF) needed for the sharpening was derived analytically from published modulation transfer function (MTF) values. Synthetic Planetscope red-edge and SWIR bands were derived by linear regression of the Planetscope visible and NIR bands with the Sentinel-2 red-edge and SWIR bands. The HPM and M3 sharpening results were evaluated visually and quantitatively using the Q2n metric that quantifies spectral and spatial distortion. The HPM and M3 sharpening methods provided visually coherent and spatially detailed visible and NIR wavelength sharpened results with low distortion (Q2n values > 0.91). The sharpened red-edge and SWIR results were also coherent but had greater distortion (Q2n values > 0.76). Detailed examination at locations where surface changes between the Sentinel-2 and the Planetscope acquisitions occurred revealed that the HPM method, unlike the M3 method, could reliably sharpen the bands affected by the change. This is because HPM sharpening uses a per-pixel reflectance ratio in the spatial detail modulation which is relatively stable to reflectance changes. The paper concludes with a discussion of the implications of this research and the recommendation that the HPM sharpening be used considering its better performance when there are surface changes.

scholarly journals Assessing Leaf Biomass of Agave sisalana Using Sentinel-2 Vegetation Indices

2021 ◽  
Vol 13 (2) ◽  
pp. 233
Author(s):  
Ilja Vuorinne ◽  
Janne Heiskanen ◽  
Petri K. E. Pellikka
Keyword(s):  
Near Infrared ◽  
Vegetation Indices ◽  
Fibre Production ◽  
Additive Models ◽  
Leaf Biomass ◽  
Ground Vegetation ◽  
Perennial Crop ◽  
Red Edge ◽  
Agave Sisalana ◽  
Sentinel 2

Biomass is a principal variable in crop monitoring and management and in assessing carbon cycling. Remote sensing combined with field measurements can be used to estimate biomass over large areas. This study assessed leaf biomass of Agave sisalana (sisal), a perennial crop whose leaves are grown for fibre production in tropical and subtropical regions. Furthermore, the residue from fibre production can be used to produce bioenergy through anaerobic digestion. First, biomass was estimated for 58 field plots using an allometric approach. Then, Sentinel-2 multispectral satellite imagery was used to model biomass in an 8851-ha plantation in semi-arid south-eastern Kenya. Generalised Additive Models were employed to explore how well biomass was explained by various spectral vegetation indices (VIs). The highest performance (explained deviance = 76%, RMSE = 5.15 Mg ha−1) was achieved with ratio and normalised difference VIs based on the green (R560), red-edge (R740 and R783), and near-infrared (R865) spectral bands. Heterogeneity of ground vegetation and resulting background effects seemed to limit model performance. The best performing VI (R740/R783) was used to predict plantation biomass that ranged from 0 to 46.7 Mg ha−1 (mean biomass 10.6 Mg ha−1). The modelling showed that multispectral data are suitable for assessing sisal leaf biomass at the plantation level and in individual blocks. Although these results demonstrate the value of Sentinel-2 red-edge bands at 20-m resolution, the difference from the best model based on green and near-infrared bands at 10-m resolution was rather small.

scholarly journals Spaceborne Estimation of Leaf Area Index in Cotton, Tomato, and Wheat Using Sentinel-2

Land ◽  
2021 ◽  
Vol 10 (5) ◽  
pp. 505
Author(s):  
Gregoriy Kaplan ◽  
Offer Rozenstein
Keyword(s):  
Water Vapor ◽  
Leaf Area Index ◽  
Leaf Area ◽  
Vegetation Index ◽  
Near Infrared ◽  
Linear Regression Models ◽  
Area Index ◽  
Estimation Performance ◽  
Red Edge ◽  
Sentinel 2

Satellite remote sensing is a useful tool for estimating crop variables, particularly Leaf Area Index (LAI), which plays a pivotal role in monitoring crop development. The goal of this study was to identify the optimal Sentinel-2 bands for LAI estimation and to derive Vegetation Indices (VI) that are well correlated with LAI. Linear regression models between time series of Sentinel-2 imagery and field-measured LAI showed that Sentinel-2 Band-8A—Narrow Near InfraRed (NIR) is more accurate for LAI estimation than the traditionally used Band-8 (NIR). Band-5 (Red edge-1) showed the lowest performance out of all red edge bands in tomato and cotton. A novel finding was that Band 9 (Water vapor) showed a very high correlation with LAI. Bands 1, 2, 3, 4, 5, 11, and 12 were saturated at LAI ≈ 3 in cotton and tomato. Bands 6, 7, 8, 8A, and 9 were not saturated at high LAI values in cotton and tomato. The tomato, cotton, and wheat LAI estimation performance of ReNDVI (R2 = 0.79, 0.98, 0.83, respectively) and two new VIs (WEVI (Water vapor red Edge Vegetation Index) (R2 = 0.81, 0.96, 0.71, respectively) and WNEVI (Water vapor narrow NIR red Edge Vegetation index) (R2 = 0.79, 0.98, 0.79, respectively)) were higher than the LAI estimation performance of the commonly used NDVI (R2 = 0.66, 0.83, 0.05, respectively) and other common VIs tested in this study. Consequently, reNDVI, WEVI, and WNEVI can facilitate more accurate agricultural monitoring than traditional VIs.

scholarly journals Coseismic displacements of the 14 November 2016 Mw7.8 Kaikoura, New Zealand, earthquake using an optical cubesat constellation

2017 ◽  
Author(s):  
Andreas Kääb ◽  
Bas Altena ◽  
Joseph Mascaro
Keyword(s):  
New Zealand ◽  
Land Surface ◽  
Near Infrared ◽  
Sar Interferometry ◽  
Optical Methods ◽  
Optical Data ◽  
Surface Displacements ◽  
Before And After ◽  
Optical Satellite Images ◽  
Sentinel 2

Abstract. Satellite measurements of coseismic displacements are typically based on Synthetic Aperture Radar (SAR) interferometry or amplitude tracking, or based on optical data such as from Landsat, Sentinel-2, SPOT, ASTER, very-high resolution satellites, or airphotos. Here, we evaluate a new class of optical satellite images for this purpose – data from cubesats. More specific, we investigate the PlanetScope cubesat constellation for horizontal surface displacements by the 14 November 2016 Mw7.8 Kaikoura, New Zealand, earthquake. Single PlanetScope scenes are 2–4 m resolution visible and near-infrared frame images of approximately 20–30 km × 9–15 km in size, acquired in continuous sequence along an orbit of approximately 375–475 km height. From single scenes or mosaics from before and after the earthquake we observe surface displacements of up to almost 10 m and estimate a matching accuracy from PlanetScope data of up to ±0.2 pixels (~ ±0.6 m). This accuracy, the daily revisit anticipated for the PlanetScope constellation for the entire land surface of Earth, and a number of other features, together offer new possibilities for investigating coseismic and other Earth surface displacements and managing related hazards and disasters, and complement existing SAR and optical methods. For comparison and for a better regional overview we also match the coseismic displacements by the 2016 Kaikoura earthquake using Landsat8 and Sentinel-2 data.

Rapid dehazing algorithm based on large-scale median filtering for high-resolution visible near-infrared remote sensing images

2014 ◽  
Vol 12 (05) ◽  
pp. 1461010 ◽  
Author(s):  
Changmiao Hu ◽  
Ping Tang
Keyword(s):  
Remote Sensing ◽  
High Resolution ◽  
Land Surface ◽  
Large Scale ◽  
Near Infrared ◽  
Low Frequency ◽  
Median Filtering ◽  
Remote Sensing Images ◽  
Infrared Band ◽  
Remote Sensing Image Processing

In recent years, China's demand for satellite remote sensing images increased. Thus, the country launched a series of satellites equipped with high-resolution sensors. The resolutions of these satellites range from 30 m to a few meters, and the spectral range covers the visible to the near-infrared band. These satellite images are mainly used for environmental monitoring, mapping, land surface classification and other fields. However, haze is an important factor that often affects image quality. Thus, dehazing technology is becoming a critical step in high-resolution remote sensing image processing. This paper presents a rapid algorithm for dehazing based on a semi-physical haze model. Large-scale median filtering technique is used to extract large areas of bright, low-frequency information from images to estimate the distribution and thickness of the haze. Four images from different satellites are used for experiment. Results show that the algorithm is valid, fast, and suitable for the rapid dehazing of numerous large-sized high-resolution remote sensing images in engineering applications.

scholarly journals Evaluation of TsHARP Utility for Thermal Sharpening of Sentinel-3 Satellite Images Using Sentinel-2 Visual Imagery

2019 ◽  
Vol 11 (19) ◽  
pp. 2304 ◽  
Author(s):  
Hanna Huryna ◽  
Yafit Cohen ◽  
Arnon Karnieli ◽  
Natalya Panov ◽  
William P. Kustas ◽  
...  
Keyword(s):  
Spatial Resolution ◽  
Land Surface ◽  
Near Infrared ◽  
Landsat 8 ◽  
Large Area ◽  
Primary Methods ◽  
Thermal Images ◽  
Spatially Distributed ◽  
The Difference ◽  
Sentinel 2

A spatially distributed land surface temperature is important for many studies. The recent launch of the Sentinel satellite programs paves the way for an abundance of opportunities for both large area and long-term investigations. However, the spatial resolution of Sentinel-3 thermal images is not suitable for monitoring small fragmented fields. Thermal sharpening is one of the primary methods used to obtain thermal images at finer spatial resolution at a daily revisit time. In the current study, the utility of the TsHARP method to sharpen the low resolution of Sentinel-3 thermal data was examined using Sentinel-2 visible-near infrared imagery. Compared to Landsat 8 fine thermal images, the sharpening resulted in mean absolute errors of ~1 °C, with errors increasing as the difference between the native and the target resolutions increases. Part of the error is attributed to the discrepancy between the thermal images acquired by the two platforms. Further research is due to test additional sites and conditions, and potentially additional sharpening methods, applied to the Sentinel platforms.

scholarly journals Identification of Continental Wetlands Using Different Orbital Remote Sensors

Terr Plural ◽  
2021 ◽  
Vol 15 ◽  
pp. 1-25
Author(s):  
Isadora Taborda Silva ◽  
Jéssica Rabito Chaves ◽  
Helen Rezende Figueiredo ◽  
Bruno Silva Ferreira ◽  
César Claudio Cáceres Encina ◽  
...  
Keyword(s):  
Near Infrared ◽  
Spectral Band ◽  
Landsat 8 ◽  
Remote Sensors ◽  
False Color ◽  
False Color Composite ◽  
International Importance ◽  
Color Composite ◽  
Shortwave Infrared ◽  
Sentinel 2

This paper evaluates the potential of false-color composite images, from 3 different remote sensing satellites, for the identification of continental wetlands. Landsat 8, Sentinel-2 and CBERS-4 scenes from three different Ramsar sites (i.e., sites designated to be of international importance) two sites located within the Mato-Grossense Pantanal and one within the Sul-mato-grossense were used for analyses. For each site, images from both the dry and rainy seasons were analyzed using Near-Infrared (NIR), Shortwave Infrared (SWIR), and visible (VIS) bands. The results show that false-color composite images from both the Landsat 8 and the Sentinel-2 satellites, with both SWIR 2-NIR-BLUE and NIR-SWIR-RED spectral band combinations, allow the identification of wetlands.

scholarly journals Continuous Monitoring of Cotton Stem Water Potential using Sentinel-2 Imagery

2020 ◽  
Vol 12 (7) ◽  
pp. 1176 ◽  
Author(s):  
Yukun Lin ◽  
Zhe Zhu ◽  
Wenxuan Guo ◽  
Yazhou Sun ◽  
Xiaoyuan Yang ◽  
...  
Keyword(s):  
Machine Learning ◽  
Linear Regression ◽  
Water Potential ◽  
Large Scale ◽  
Temporal Frequency ◽  
Vegetation Indices ◽  
Stem Water Potential ◽  
Spectral Bands ◽  
Red Edge ◽  
Sentinel 2

Monitoring cotton status during the growing season is critical in increasing production efficiency. The water status in cotton is a key factor for yield and cotton quality. Stem water potential (SWP) is a precise indicator for assessing cotton water status. Satellite remote sensing is an effective approach for monitoring cotton growth at a large scale. The aim of this study is to estimate cotton water stress at a high temporal frequency and at a large scale. In this study, we measured midday SWP samples according to the acquisition dates of Sentinel-2 images and used them to build linear-regression-based and machine-learning-based models to estimate cotton water stress during the growing season (June to August, 2018). For the linear-regression-based method, we estimated SWP based on different Sentinel-2 spectral bands and vegetation indices, where the normalized difference index 45 (NDI45) achieved the best performance (R2 = 0.6269; RMSE = 3.6802 (-1*swp (bars))). For the machine-learning-based method, we used random forest regression to estimate SWP and received even better results (R2 = 0.6709; RMSE = 3.3742 (-1*swp (bars))). To find the best selection of input variables for the machine-learning-based approach, we tried three different data input datasets, including (1) 9 original spectral bands (e.g., blue, green, red, red edge, near infrared (NIR), and shortwave infrared (SWIR)), (2) 21 vegetation indices, and (3) a combination of original Sentinel-2 spectral bands and vegetation indices. The highest accuracy was achieved when only the original spectral bands were used. We also found the SWIR and red edge band were the most important spectral bands, and the vegetation indices based on red edge and NIR bands were particularly helpful. Finally, we applied the best approach for the linear-regression-based and the machine-learning-based methods to generate cotton water potential maps at a large scale and high temporal frequency. Results suggests that the methods developed here has the potential for continuous monitoring of SWP at large scales and the machine-learning-based method is preferred.

scholarly journals Deriving Non-Cloud Contaminated Sentinel-2 Images with RGB and Near-Infrared Bands from Sentinel-1 Images Based on a Conditional Generative Adversarial Network

2021 ◽  
Vol 13 (8) ◽  
pp. 1512
Author(s):  
Quan Xiong ◽  
Liping Di ◽  
Quanlong Feng ◽  
Diyou Liu ◽  
Wei Liu ◽  
...  
Keyword(s):  
Land Surface ◽  
Near Infrared ◽  
Similarity Index ◽  
Data Availability ◽  
Optical Data ◽  
Generative Adversarial Network ◽  
Spectral Angle Mapper ◽  
Adversarial Network ◽  
Target Date ◽  
Sentinel 2

Sentinel-2 images have been widely used in studying land surface phenomena and processes, but they inevitably suffer from cloud contamination. To solve this critical optical data availability issue, it is ideal to fuse Sentinel-1 and Sentinel-2 images to create fused, cloud-free Sentinel-2-like images for facilitating land surface applications. In this paper, we propose a new data fusion model, the Multi-channels Conditional Generative Adversarial Network (MCcGAN), based on the conditional generative adversarial network, which is able to convert images from Domain A to Domain B. With the model, we were able to generate fused, cloud-free Sentinel-2-like images for a target date by using a pair of reference Sentinel-1/Sentinel-2 images and target-date Sentinel-1 images as inputs. In order to demonstrate the superiority of our method, we also compared it with other state-of-the-art methods using the same data. To make the evaluation more objective and reliable, we calculated the root-mean-square-error (RSME), R2, Kling–Gupta efficiency (KGE), structural similarity index (SSIM), spectral angle mapper (SAM), and peak signal-to-noise ratio (PSNR) of the simulated Sentinel-2 images generated by different methods. The results show that the simulated Sentinel-2 images generated by the MCcGAN have a higher quality and accuracy than those produced via the previous methods.

scholarly journals On the Configuration and Initialization of a Large Scale Hydrological Land Surface Model to Represent Permafrost

2019 ◽  
Author(s):  
Mohamed E. Elshamy ◽  
Daniel Princz ◽  
Gonzalo Sapriza-Azuri ◽  
Al Pietroniro ◽  
Howard S. Wheater ◽  
...  
Keyword(s):  
Land Surface ◽  
Large Scale ◽  
Land Surface Model ◽  
Organic Soil ◽  
Organic Soils ◽  
Surface Model ◽  
Soil Profiles ◽  
Computationally Efficient ◽  
Deep Soil ◽  
Mackenzie River

Abstract. Permafrost is an important feature of cold regions hydrology, particularly in basins such as the Mackenzie River Basin (MRB), and needs to be properly represented in hydrological and land surface models (H-LSMs) built into existing Earth System models (ESM), especially under the unprecedented climate warming trends that have been observed. Higher rates of warming have been reported in high latitudes compared to the global average resulting in permafrost thaw with wide-ranging implications for hydrology and feedbacks to climate. The current generation of H-LSMs is being improved to simulate permafrost dynamics by allowing deep soil profiles and incorporating organic soils explicitly. Deeper soil profiles have larger hydraulic and thermal memories that require more effort to initialize. This study aims to devise a robust, yet computationally efficient, initialization and parameterization approach applicable to regions where data are scarce and simulations typically require large computational resources. The study further demonstrates an upscaling approach to inform large-scale ESM simulations based on the insights gained by modelling at small scales. We used permafrost observations from three sites along the Mackenzie River Valley spanning different permafrost classes to test the validity of the approach. Results show generally good performance in reproducing present-climate permafrost properties at the three sites. The results also emphasize the sensitivity of the simulations to the soil layering scheme used, the depth to bedrock and the organic soil properties.

scholarly journals Mapping Height and Aboveground Biomass of Mangrove Forests on Hainan Island Using UAV-LiDAR Sampling

2019 ◽  
Vol 11 (18) ◽  
pp. 2156 ◽  
Author(s):  
Dezhi Wang ◽  
Bo Wan ◽  
Penghua Qiu ◽  
Zejun Zuo ◽  
Run Wang ◽  
...  
Keyword(s):  
Low Cost ◽  
Hainan Island ◽  
Average Height ◽  
Mangrove Forests ◽  
Infrared Band ◽  
Red Edge ◽  
Extensive Field ◽  
Aerial Vehicle ◽  
Shortwave Infrared ◽  
Sentinel 2

Hainan Island is the second-largest island in China and has the most species-diverse mangrove forests in the country. To date, the height and aboveground ground biomass (AGB) of the mangrove forests on Hainan Island are unknown, partly as a result of the challenges faced during extensive field sampling in mangrove habitats (intertidal mudflats inundated by periodic seawater). Therefore, this study used a low-cost UAV-LiDAR (light detection and ranging sensor mounted on an unmanned aerial vehicle) system as a sampling tool and Sentinel-2 imagery as auxiliary data to estimate and map the mangrove height and AGB on Hainan Island. Hainan Island has 3697.02 hectares of mangrove forests with an average patch area of approximately 1 ha. The results show that the mangroves on whole Hainan Island have an average height of 6.99 m, a total AGB of 474,199.31 Mg and an AGB density of 128.27 Mg ha−1. The AGB hot spots are located in Qinglan Harbor and the south of Dongzhai Harbor. The proposed height model LiDAR-S2 performed well with an R2 of 0.67 and an RMSE (root mean square error) of 1.90 m; the proposed AGB model G~LiDAR~S2 performed better (an R2 of 0.62 and an RMSE of 50.36 Mg ha−1) than the traditional AGB model G~S2 that directly related ground plots and Sentinel-2 data. The results also indicate that the LiDAR metrics describing the canopy’s thickness and its top and bottom characteristics are the most important variables for mangrove AGB estimation. For the Sentinel-2 indices, the red-edge and shortwave infrared features, especially the red-edge 1 and shortwave infrared Band 11 features, play the most important roles in estimating mangrove AGB and height. In conclusion, this paper presents the first mangrove height and AGB maps of Hainan Island and demonstrates the feasibility of using UAV-LiDAR as a sampling tool for mangrove forests.

Sign in / Sign up

Export Citation Format

Share Document