scholarly journals Mapping Topobathymetry in a Shallow Tidal Environment Using Low-Cost Technology

2020 ◽  
Vol 12 (9) ◽  
pp. 1394 ◽  
Author(s):  
Sibila A. Genchi ◽  
Alejandro J. Vitale ◽  
Gerardo M. E. Perillo ◽  
Carina Seitz ◽  
Claudio A. Delrieux
Keyword(s):  
Root Mean Square Error ◽  
Mean Square Error ◽  
Root Mean Square ◽  
Low Cost ◽  
Vertical Plane ◽  
Detailed Knowledge ◽  
Mean Square ◽  
Bahía Blanca Estuary ◽  
Weighting Method ◽  
Data Source

Detailed knowledge of nearshore topography and bathymetry is required for a wide variety of purposes, including ecosystem protection, coastal management, and flood and erosion monitoring and research, among others. Both topography and bathymetry are usually studied separately; however, many scientific questions and challenges require an integrated approach. LiDAR technology is often the preferred data source for the generation of topobathymetric models, but because of its high cost, it is necessary to exploit other data sources. In this regard, the main goal of this study was to present a methodological proposal to generate a topobathymetric model, using low-cost unmanned platforms (unmanned aerial vehicle and unmanned surface vessel) in a very shallow/shallow and turbid tidal environment (Bahía Blanca estuary, Argentina). Moreover, a cross-analysis of the topobathymetric and the tide level data was conducted, to provide a classification of hydrogeomorphic zones. As a main result, a continuous terrain model was built, with a spatial resolution of approximately 0.08 m (topography) and 0.50 m (bathymetry). Concerning the structure from motion-derived topography, the accuracy gave a root mean square error of 0.09 m for the vertical plane. The best interpolated bathymetry (inverse distance weighting method), which was aligned to the topography (as reference), showed a root mean square error of 0.18 m (in average) and a mean absolute error of 0.05 m. The final topobathymetric model showed an adequate representation of the terrain, making it well suited for examining many landforms. This study helps to confirm the potential for remote sensing of shallow tidal environments by demonstrating how the data source heterogeneity can be exploited.

scholarly journals Low Cost Automatic Reconstruction of Tree Structure by AdQSM with Terrestrial Close-Range Photogrammetry

Forests ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 1020
Author(s):  
Yanqi Dong ◽  
Guangpeng Fan ◽  
Zhiwu Zhou ◽  
Jincheng Liu ◽  
Yongguo Wang ◽  
...  
Keyword(s):  
Root Mean Square Error ◽  
Mean Square Error ◽  
Root Mean Square ◽  
Low Cost ◽  
Reference Value ◽  
Tree Height ◽  
Point Clouds ◽  
Tree Structure ◽  
Mean Square ◽  
Tree Model

The quantitative structure model (QSM) contains the branch geometry and attributes of the tree. AdQSM is a new, accurate, and detailed tree QSM. In this paper, an automatic modeling method based on AdQSM is developed, and a low-cost technical scheme of tree structure modeling is provided, so that AdQSM can be freely used by more people. First, we used two digital cameras to collect two-dimensional (2D) photos of trees and generated three-dimensional (3D) point clouds of plot and segmented individual tree from the plot point clouds. Then a new QSM-AdQSM was used to construct tree model from point clouds of 44 trees. Finally, to verify the effectiveness of our method, the diameter at breast height (DBH), tree height, and trunk volume were derived from the reconstructed tree model. These parameters extracted from AdQSM were compared with the reference values from forest inventory. For the DBH, the relative bias (rBias), root mean square error (RMSE), and coefficient of variation of root mean square error (rRMSE) were 4.26%, 1.93 cm, and 6.60%. For the tree height, the rBias, RMSE, and rRMSE were—10.86%, 1.67 m, and 12.34%. The determination coefficient (R2) of DBH and tree height estimated by AdQSM and the reference value were 0.94 and 0.86. We used the trunk volume calculated by the allometric equation as a reference value to test the accuracy of AdQSM. The trunk volume was estimated based on AdQSM, and its bias was 0.07066 m3, rBias was 18.73%, RMSE was 0.12369 m3, rRMSE was 32.78%. To better evaluate the accuracy of QSM’s reconstruction of the trunk volume, we compared AdQSM and TreeQSM in the same dataset. The bias of the trunk volume estimated based on TreeQSM was −0.05071 m3, and the rBias was −13.44%, RMSE was 0.13267 m3, rRMSE was 35.16%. At 95% confidence interval level, the concordance correlation coefficient (CCC = 0.77) of the agreement between the estimated tree trunk volume of AdQSM and the reference value was greater than that of TreeQSM (CCC = 0.60). The significance of this research is as follows: (1) The automatic modeling method based on AdQSM is developed, which expands the application scope of AdQSM; (2) provide low-cost photogrammetric point cloud as the input data of AdQSM; (3) explore the potential of AdQSM to reconstruct forest terrestrial photogrammetric point clouds.

Evaluation of a Low-Cost Pneumatic Plantar Pressure Insole for Predicting Ground Contact Kinetics

2016 ◽  
Vol 32 (2) ◽  
pp. 215-220 ◽  
Author(s):  
Daniel A. Jacobs ◽  
Daniel P. Ferris
Keyword(s):  
Root Mean Square Error ◽  
Mean Square Error ◽  
Root Mean Square ◽  
Plantar Pressure ◽  
Center Of Pressure ◽  
Low Cost ◽  
Position Vector ◽  
Mean Square ◽  
Torque Vector ◽  
Sit To Stand

Instrumented insoles could benefit locomotion research on healthy and clinical populations by providing data in natural settings outside of the laboratory. We designed a low-cost, instrumented insole with 8 pneumatic bladders to measure localized plantar pressure information. We collected gait data during treadmill walking at 1.0 m/s and 1.5 m/s and for sit-to-stand and stand-tosit tasks for 10 subjects. We estimated a common representation of ground kinetics (3-component force vector, 2-component center of pressure position vector, and a single-component torque vector) from the insole data. We trained an intertask neural network for each component of the kinetic data. For the walking tasks at 1.0 m/s and 1.5 m/s, the normalized root mean square error was between 3.1% and 12.9% and for the sit-to-stand and stand-to-sit tasks, the normalized root mean square error was between 3.3% and 21.3% Our findings suggest that the proposed low-cost, instrumented insoles could provide useful data about movement kinetics during real-world activities.

scholarly journals Evaluation methods for low-cost particulate matter sensors

2021 ◽  
Author(s):  
Jeffrey K. Bean
Keyword(s):  
Quality Assurance ◽  
Particulate Matter ◽  
Root Mean Square Error ◽  
Mean Square Error ◽  
Root Mean Square ◽  
Prediction Interval ◽  
Low Cost ◽  
Sensor Data ◽  
Rural Site ◽  
Mean Square

Abstract. Understanding and improving the quality of data generated from low-cost sensors is a crucial step in using these sensors to fill gaps in air quality measurement and understanding. This paper shows results from a 10-month long campaign that included side-by-side measurements and comparison between EPA-approved reference instruments and low-cost particulate matter sensors in Bartlesville, Oklahoma. At this rural site in the Midwestern United States the instruments typically encountered only low (under 20 µg/m3) concentrations of particulate matter, however higher concentrations (50–400 µg/m3) were observed on three different days during what were likely agricultural burning events. This study focused on methods for understanding and improving data quality for low-cost particulate matter sensors. The data offered insights on how averaging time, choice of reference instrument, and the observation of higher pollutant concentrations can all impact performance indicators (R2 and root mean square error) for an evaluation. The influence of these factors should be considered when comparing one sensor to another or when determining whether a sensor can produce data that fits a specific need. Though R2 and root mean square error remain the dominant metrics in sensor evaluations, an alternative approach using a prediction interval may offer more consistency between evaluations and a more direct interpretation of sensor data following an evaluation. Ongoing quality assurance for sensor data is needed to ensure data continues to meet expectations. Observations of trends in linear regression parameters and sensor bias were used to analyze calibration and other quality assurance techniques.

scholarly journals Evaluation methods for low-cost particulate matter sensors

2021 ◽  
Vol 14 (11) ◽  
pp. 7369-7379
Author(s):  
Jeffrey K. Bean
Keyword(s):  
United States ◽  
Quality Assurance ◽  
Particulate Matter ◽  
Root Mean Square Error ◽  
Mean Square Error ◽  
Root Mean Square ◽  
Low Cost ◽  
Sensor Data ◽  
Rural Site ◽  
Mean Square

Abstract. Understanding and improving the quality of data generated from low-cost sensors represent a crucial step in using these sensors to fill gaps in air quality measurement and understanding. This paper shows results from a 10-month-long campaign that included side-by-side measurements and comparison between reference instruments approved by the United States Environmental Protection Agency (EPA) and low-cost particulate matter sensors in Bartlesville, Oklahoma. At this rural site in the Midwestern United States the instruments typically encountered only low (under 20 µg m−3) concentrations of particulate matter; however, higher concentrations (50–400 µg m−3) were observed on 3 different days during what were likely agricultural burning events. This study focused on methods for understanding and improving data quality for low-cost particulate matter sensors. The data offered insights on how averaging time, choice of reference instrument, and the observation of higher pollutant concentrations can all impact performance indicators (R2 and root mean square error) for an evaluation. The influence of these factors should be considered when comparing one sensor to another or when determining whether a sensor can produce data that fit a specific need. Though R2 and root mean square error remain the dominant metrics in sensor evaluations, an alternative approach using a prediction interval may offer more consistency between evaluations and a more direct interpretation of sensor data following an evaluation. Ongoing quality assurance for sensor data is needed to ensure that data continue to meet expectations. Observations of trends in linear regression parameters and sensor bias were used to analyze calibration and other quality assurance techniques.

scholarly journals Estimation of Apple Flowering Frost Loss for Fruit Yield Based on Gridded Meteorological and Remote Sensing Data in Luochuan, Shaanxi Province, China

2021 ◽  
Vol 13 (9) ◽  
pp. 1630
Author(s):  
Yaohui Zhu ◽  
Guijun Yang ◽  
Hao Yang ◽  
Fa Zhao ◽  
Shaoyu Han ◽  
...  
Keyword(s):  
Remote Sensing ◽  
Root Mean Square Error ◽  
Mean Square Error ◽  
Root Mean Square ◽  
Minimum Temperature ◽  
Price Regulation ◽  
Flowering Period ◽  
Mean Square ◽  
Prevention Measures ◽  
Agricultural Insurance

With the increase in the frequency of extreme weather events in recent years, apple growing areas in the Loess Plateau frequently encounter frost during flowering. Accurately assessing the frost loss in orchards during the flowering period is of great significance for optimizing disaster prevention measures, market apple price regulation, agricultural insurance, and government subsidy programs. The previous research on orchard frost disasters is mainly focused on early risk warning. Therefore, to effectively quantify orchard frost loss, this paper proposes a frost loss assessment model constructed using meteorological and remote sensing information and applies this model to the regional-scale assessment of orchard fruit loss after frost. As an example, this article examines a frost event that occurred during the apple flowering period in Luochuan County, Northwestern China, on 17 April 2020. A multivariable linear regression (MLR) model was constructed based on the orchard planting years, the number of flowering days, and the chill accumulation before frost, as well as the minimum temperature and daily temperature difference on the day of frost. Then, the model simulation accuracy was verified using the leave-one-out cross-validation (LOOCV) method, and the coefficient of determination (R2), the root mean square error (RMSE), and the normalized root mean square error (NRMSE) were 0.69, 18.76%, and 18.76%, respectively. Additionally, the extended Fourier amplitude sensitivity test (EFAST) method was used for the sensitivity analysis of the model parameters. The results show that the simulated apple orchard fruit number reduction ratio is highly sensitive to the minimum temperature on the day of frost, and the chill accumulation and planting years before the frost, with sensitivity values of ≥0.74, ≥0.25, and ≥0.15, respectively. This research can not only assist governments in optimizing traditional orchard frost prevention measures and market price regulation but can also provide a reference for agricultural insurance companies to formulate plans for compensation after frost.

Comparison of Thresholding and Edge Detection Segmentation Techniques

2013 ◽  
Vol 860-863 ◽  
pp. 2783-2786
Author(s):  
Yu Bing Dong ◽  
Hai Yan Wang ◽  
Ming Jing Li
Keyword(s):  
Image Segmentation ◽  
Root Mean Square Error ◽  
Edge Detection ◽  
Mean Square Error ◽  
Root Mean Square ◽  
Experimental Results ◽  
Mean Square ◽  
Segmentation Method ◽  
Segmentation Algorithms

Edge detection and thresholding segmentation algorithms are presented and tested with variety of grayscale images in different fields. In order to analyze and evaluate the quality of image segmentation, Root Mean Square Error is used. The smaller error value is, the better image segmentation effect is. The experimental results show that a segmentation method is not suitable for all images segmentation.

Quantitative Analysis of Forsythiae fructus by Near Infrared Spectroscopy

2013 ◽  
Vol 807-809 ◽  
pp. 1967-1971
Author(s):  
Yan Bai ◽  
Xiao Yan Duan ◽  
Hai Yan Gong ◽  
Cai Xia Xie ◽  
Zhi Hong Chen ◽  
...  
Keyword(s):  
Infrared Spectroscopy ◽  
Root Mean Square Error ◽  
Mean Square Error ◽  
Root Mean Square ◽  
Near Infrared Spectroscopy ◽  
Near Infrared ◽  
Cross Validation ◽  
Ethanol Extract ◽  
Mean Square ◽  
Validation Set

In this paper, the content of forsythoside A and ethanol-extract were rapidly determinated by near-infrared reflectance spectroscopy (NIRS). 85 samples of Forsythiae Fructus harvested in Luoyang from July to September in 2012 were divided into a calibration set (75 samples) and a validation set (10 samples). In combination with the partical least square (PLS), the quantitative calibration models of forsythoside A and ethanol-extract were established. The correlation coefficient of cross-validation (R2) was 0.98247 and 0.97214 for forsythoside A and ethanol-extract, the root-mean-square error of calibration (RMSEC) was 0.184 and 0.570, the root-mean-square error of cross-validation (RMSECV) was 0.81736 and 0.36656. The validation set were used to evaluate the performance of the models, the root-mean-square error of prediction (RMSEP) was 0.221 and 0.518. The results indicated that it was feasible to determine the content of forsythoside A and ethanol-extract in Forsythiae Fructus by near-infrared spectroscopy.

Analysis of candlenut oil as oil adulterant in three functional oils of soybean oil, sunflower oil and grapeseed oil in quaternary mixture systems using FTIR spectroscopy and chemometrics

Food Research ◽  
2021 ◽  
Vol 5 (2) ◽  
pp. 248-253
Author(s):  
A.B. Riyanta ◽  
S. Riyanto ◽  
E. Lukitaningsih ◽  
A. Rohman
Keyword(s):  
Root Mean Square Error ◽  
Soybean Oil ◽  
Ftir Spectroscopy ◽  
Mean Square Error ◽  
Root Mean Square ◽  
Sunflower Oil ◽  
Ftir Spectra ◽  
Mean Square ◽  
Grapeseed Oil ◽  
Quaternary Mixture

Soybean oil (SBO), sunflower oil (SFO) and grapeseed oil (GPO) contain high levels of unsaturated fats that are good for health and have proximity to candlenut oil. Candlenut oil (CNO) has a lower price and easier to get oil from that seeds than other seed oils, so it is used as adulteration for gains. Therefore, authentication is required to ensure the purity of oils by proper analysis. This research was aimed to highlight the FTIR spectroscopy application with multivariate calibration is a potential analysis for scanning the quaternary mixture of CNO, SBO, SFO and GPO. CNO quantification was performed using multivariate calibrations of principle component (PCR) regression and partial least (PLS) square to predict the model from the optimization FTIR spectra regions. The highest R2 and the lowest values of root mean square error of calibration (RMSEC) and root mean square error of prediction (RMSEP) were used as the basis for selection of multivariate calibrations created using several wavenumbers region of FTIR spectra. Wavenumbers regions of 4000-650 cm-1 from the second derivative FTIR-ATR spectra using PLS was used for quantitative analysis of CNO in quaternary mixture with SBO, SFO and GPO with R2 calibration = 0.9942 and 0.0239% for RMSEC value and 0.0495%. So, it can be concluded the use of FTIR spectra combination with PLS is accurate to detect quaternary mixtures of CNO, SBO, SFO and GPO with the highest R2 values and the lowest RMSEC and RMSEP values.

Sign in / Sign up

Export Citation Format

Share Document