scholarly journals Increasing the Number of Sea Surface Reflected Signals Received by GNSS-Reflectometry Altimetry Satellite Using the Nadir Antenna Observation Capability Optimization Method

2019 ◽  
Vol 11 (21) ◽  
pp. 2473
Author(s):  
Liu ◽  
Zheng ◽  
Wu ◽  
Kang ◽  
Li ◽  
...  
Keyword(s):  
Spatial Resolution ◽  
Electromagnetic Scattering ◽  
Elevation Angle ◽  
Beam Width ◽  
Optimization Method ◽  
Satellite System ◽  
Sea Surface ◽  
Antenna Gain ◽  
Sea Surface Topography ◽  
Reflected Signal

High spatial resolution Global Navigation Satellite System-Reflectometry (GNSS-R) sea surface altimetry is of great significance for extracting precise information from sea surface topography. The nadir antenna is one of the key payloads for the GNSS-R altimetry satellite to capture and track the sea surface GNSS reflected signal. The observation capability of the nadir antenna directly determines the number of received reflected signals, which, in turn, affects the spatial resolution of the GNSS-R altimetry. The parameters affecting the ability of the nadir antenna to receive the reflected signal mainly include antenna gain, half-power beam width (HPBW), and pointing angle. Thus far, there are rarely studies on the observation capability of GNSS-R satellite nadir antenna. The design of operational satellite antenna does not fully combine the above three parameters to optimize the design of GNSS-R nadir antenna. Therefore, it is necessary to establish a GNSS-R spaceborne nadir antenna observation capability optimization method. This is the key to improving the number of sea surface reflected signals received by the GNSS-R altimeter satellites, thereby increasing the spatial resolution of the altimetry. This paper has carried out the following research on this. Firstly, based on the GNSS-R geometric relationship and signal processing theory, the nadir antenna signal-to-noise ratio model (NASNRM) with the gain and the elevation angle at the specular point (SP) as the main parameters is established. The accuracy of the model was verified using TechDemoSat-1 (TDS-1) observations. Secondly, based on the theory of electromagnetic scattering, considering the influence of HPBW and pointing angle on the antenna footprint size, a specular point filtering algorithm (SPFA) is proposed. Combined with the results obtained by NASNRM, the number of available specular points (SPs) is counted. The results show that as the antenna gain and the nadir-pointing angle increase, the number of SPs can reach a peak and then gradually decrease. Thirdly, combined with NASNRM and SPSA, a nadir antenna observation capability optimization method (NAOCOM) is proposed. The nadir antenna observation capability is characterized through the reflected signal utilization, and the results obtained by the method are used to optimize the combination of nadir antenna parameters. The research shows that when the orbital height of the GNSS-R satellite is 635 km, the optimal combination of nadir antenna parameters is 20.94 dBi for the gain and 32.82 degrees for the nadir-pointing angle, which can increase the observation capability of the TDS-1 satellite nadir antenna by up to 5.38 times.

scholarly journals Improving GNSS-R Sea Surface Altimetry Precision Based on the Novel Dual Circularly Polarized Phased Array Antenna Model

2021 ◽  
Vol 13 (15) ◽  
pp. 2974
Author(s):  
Zhen Cui ◽  
Wei Zheng ◽  
Fan Wu ◽  
Xiaoping Li ◽  
Cheng Zhu ◽  
...  
Keyword(s):  
High Precision ◽  
Spatial Resolution ◽  
Measurement Accuracy ◽  
Phased Array ◽  
High Spatial Resolution ◽  
Beam Width ◽  
Sea Surface ◽  
Antenna Gain ◽  
Phased Array Antenna ◽  
Circularly Polarized

Antenna is one of the key payloads of the GNSS-R system, and the gain is an important performance parameter. The signal-to-noise ratio (SNR) of the received signal can be improved by increasing the gain of the GNSS-R antenna, therefore the measurement accuracy is improved. However, the antenna gain and its beam width, these two performance parameters, are contradictory. If the gain of the antenna is increased, its beam width will inevitably become narrower. This narrowed beam width will affect the width of the survey strip for the GNSS-R system, which cannot meet the requirement of the high-precision and high-spatial resolution spaceborne GNSS-R sea surface altimetry in the future. In this paper, a novel dual circularly polarized phased array antenna (NDCPPA) is proposed and investigated. First, the GNSS-R satellites currently operating in orbit are all cGNSS-R systems, which use the traditional element antenna (TEA) method for measurement. The antenna used in this method is with low gain, which limits the improvement of sea surface measurement accuracy. In response to this problem, this paper establishes an NDCPPA model of iGNSS-R measurement system based on the theory of coherent signal processing on the sea surface. This model uses the high-gain scanning beam to increase the gain of the iGNSS-R antenna without affecting its coverage area, thereby improving the sea surface altimetry precision. Second, in order to verify the gain improvement effect brought by adopting the NDCPPA model, an NDCPPA model verification prototype for iGNSS-R sea surface altimetry was designed and fabricated, and then measured in a microwave anechoic chamber. The measurement results show that, compared with the TEA method, the antenna gain of our proposed verification prototype is enhanced by 9.5 dB. And the measured and designed value of the gain of the verification prototype matches well. Third, based on the GPS L1 signal, the NDCPPA model is used to analyze the effect of improving the precision of sea surface altimetry. Compared with the TEA method, the proposed model can increase the altimetric precision of the nadir point from 7.27 m to 0.21 m, which effectively improves the performance of the iGNSS-R altimetry. The NDCPPA model proposed in this article can provide the theoretical method basis and the crucial technical support for the future high-precision and high-spatial-resolution GNSS-R sea surface altimetry verification satellite.

scholarly journals Measurement of the Sea Surface Height with Airborne GNSS Reflectometry and Delay Bias Calibration

2021 ◽  
Vol 13 (15) ◽  
pp. 3014
Author(s):  
Feng Wang ◽  
Dongkai Yang ◽  
Guodong Zhang ◽  
Jin Xing ◽  
Bo Zhang ◽  
...  
Keyword(s):  
Wind Speed ◽  
Arrival Time ◽  
Elevation Angle ◽  
Satellite System ◽  
Sea Surface Height ◽  
Antenna Pattern ◽  
Sea Surface ◽  
Observation Method ◽  
Global Navigation Satellite ◽  
The Impact

Sea surface height can be measured with the delay between reflected and direct global navigation satellite system (GNSS) signals. The arrival time of a feature point, such as the waveform peak, the peak of the derivative waveform, and the fraction of the peak waveform is not the true arrival time of the specular signal; there is a bias between them. This paper aims to analyze and calibrate the bias to improve the accuracy of sea surface height measured by using the reflected signals of GPS CA, Galileo E1b and BeiDou B1I. First, the influencing factors of the delay bias, including the elevation angle, receiver height, wind speed, pseudorandom noise (PRN) code of GPS CA, Galileo E1b and BeiDou B1I, and the down-looking antenna pattern are explored based on the Z-V model. The results show that (1) with increasing elevation angle, receiver height, and wind speed, the delay bias tends to decrease; (2) the impact of the PRN code is uncoupled from the elevation angle, receiver height, and wind speed, so the delay biases of Galileo E1b and BeiDou B1I can be derived from that of GPS CA by multiplication by the constants 0.32 and 0.54, respectively; and (3) the influence of the down-looking antenna pattern on the delay bias is lower than 1 m, which is less than that of other factors; hence, the effect of the down-looking antenna pattern is ignored in this paper. Second, an analytical model and a neural network are proposed based on the assumption that the influence of all factors on the delay bias are uncoupled and coupled, respectively, to calibrate the delay bias. The results of the simulation and experiment show that compared to the meter-level bias before the calibration, the calibrated bias decreases the decimeter level. Based on the fact that the specular points of several satellites are visible to the down-looking antenna, the multi-observation method is proposed to calibrate the bias for the case of unknown wind speed, and the same calibration results can be obtained when the proper combination of satellites is selected.

scholarly journals Sea Topography of the Ionian and Adriatic Seas Using Repeated GNSS Measurements

Water ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 812
Author(s):  
Sotiris Lycourghiotis
Keyword(s):  
Satellite System ◽  
Geoid Model ◽  
Sea Surface Topography ◽  
Mean Sea Surface ◽  
The Mean ◽  
A New Technique ◽  
Gnss Measurements ◽  
Global Navigation Satellite ◽  
Constant Slope ◽  
Ionian And Adriatic Seas

The mean sea surface topography of the Ionian and Adriatic Seas has been determined. This was based on six-months of Global Navigation Satellite System (GNSS) measurements which were performed on the Ionian Queen (a ship). The measurements were analyzed following a double-path methodology based on differential GNSS (D-GNSS) and precise point positioning (PPP) analysis. Numerical filtering techniques, multi-parametric accuracy analysis and a new technique for removing the meteorological tide factors were also used. Results were compared with the EGM96 geoid model. The calculated differences ranged between 0 and 48 cm. The error of the results was estimated to fall within 3.31 cm. The 3D image of the marine topography in the region shows a nearly constant slope of 4 cm/km in the N–S direction. Thus, the effectiveness of the approach “repeated GNSS measurements on the same route of a ship” developed in the context of “GNSS methods on floating means” has been demonstrated. The application of this approach using systematic multi-track recordings on conventional liner ships is very promising, as it may open possibilities for widespread use of the methodology across the world.

scholarly journals On the Impact and Mitigation of Signal Crosstalk in Ground-Based and Low Altitude Airborne GNSS-R

2021 ◽  
Vol 13 (6) ◽  
pp. 1085
Author(s):  
Corentin Lubeigt ◽  
Lorenzo Ortega ◽  
Jordi Vilà-Valls ◽  
Laurent Lestarquit ◽  
Eric Chaumette
Keyword(s):  
Specular Reflection ◽  
Signal Amplitude ◽  
Satellite System ◽  
Mitigation Strategies ◽  
Variance Estimator ◽  
Single Source ◽  
Dual Source ◽  
Reflected Signal ◽  
The Impact ◽  
Signal Crosstalk

Global Navigation Satellite System Reflectometry (GNSS-R) is a powerful way to retrieve information from a reflecting surface by exploiting GNSS as signals of opportunity. In dual antenna conventional GNSS-R architectures, the reflected signal is correlated with a clean replica to obtain the specular reflection point delay and Doppler estimates, which are further processed to obtain the GNSS-R product of interest. An important problem that may appear for low elevation satellites is signal crosstalk, that is the direct line-of-sight signal leaks into the antenna dedicated to the reflected signal. Such crosstalk may degrade the overall system performance if both signals are very close in time, similar to multipath in standard GNSS receivers, the reason why mitigation strategies must be accounted for. In this article: (i) we first provide a geometrical analysis to justify that the estimation performance is only affected for low height receivers; (ii) then, we analyze the impact of crosstalk if not taken into account, by comparing the single source conditional maximum likelihood estimator (CMLE) performance in a dual source context with the corresponding Cramér–Rao bound (CRB); (iii) we discuss dual source estimators as a possible mitigation strategy; and (iv) we investigate the performance of the so-called variance estimator, which is designed to eliminate the coherent signal part, compared to both the CRB and non-coherent dual source estimators. Simulation results are provided for representative GNSS signals to support the discussion. From this analysis, it is found that: (i) for low enough reflected-to-direct signal amplitude ratios (RDR), the crosstalk has no impact on standard single source CMLEs; (ii) for high enough signal-to-noise ratios (SNR), the dual source estimators are efficient irrespective of the RDR, then being a promising solution for any reflected signal scenario; (iii) non-coherent dual source estimators are also efficient at high SNR; and (iv) the variance estimator is efficient as long as the non-coherent part of the signal is dominant.

scholarly journals Target Localization Based on Bistatic T/R Pair Selection in GNSS-Based Multistatic Radar System

2021 ◽  
Vol 13 (4) ◽  
pp. 707
Author(s):  
Yu’e Shao ◽  
Hui Ma ◽  
Shenghua Zhou ◽  
Xue Wang ◽  
Michail Antoniou ◽  
...  
Keyword(s):  
Optimization Methods ◽  
Optimization Method ◽  
Satellite System ◽  
Radar System ◽  
Target Localization ◽  
Computational Load ◽  
Matrix Fusion ◽  
Global Navigation Satellite ◽  
Multistatic Radar ◽  
Combined Algorithm

To cope with the increasingly complex electromagnetic environment, multistatic radar systems, especially the passive multistatic radar, are becoming a trend of future radar development due to their advantages in anti-electronic jam, anti-destruction properties, and no electromagnetic pollution. However, one problem with this multi-source network is that it brings a huge amount of information and leads to considerable computational load. Aiming at the problem, this paper introduces the idea of selecting external illuminators in the multistatic passive radar system. Its essence is to optimize the configuration of multistatic T/R pairs. Based on this, this paper respectively proposes two multi-source optimization algorithms from the perspective of resolution unit and resolution capability, the Covariance Matrix Fusion Method and Convex Hull Optimization Method, and then uses a Global Navigation Satellite System (GNSS) as an external illuminator to verify the algorithms. The experimental results show that the two optimization methods significantly improve the accuracy of multistatic positioning, and obtain a more reasonable use of system resources. To evaluate the algorithm performance under large number of transmitting/receiving stations, further simulation was conducted, in which a combination of the two algorithms were applied and the combined algorithm has shown its effectiveness in minimize the computational load and retain the target localization precision at the same time.

Near Field Electromagnetic Scattering Model Studying for Coarse Sea Surface

2013 ◽  
Vol 756-759 ◽  
pp. 4586-4590
Author(s):  
Jun Gu ◽  
Kun Cai ◽  
Zi Chang Liang
Keyword(s):  
Electromagnetic Scattering ◽  
Near Field ◽  
Horn Antenna ◽  
Measured Data ◽  
Sea Surface ◽  
Scattering Coefficient ◽  
Distributed Model ◽  
Echo Signal ◽  
Scattering Model ◽  
Rough Sea

The simulated PM-spectrum fractal sea surfaces and the 3-D near-field distributed model of horn antenna are built, the near-field formulas of KA method are deduced. The near-field scattering coefficient and the Doppler echo signal of rough sea surfaces are calculated, the agreement with measured data proved the correctness and validity of the near-field scattering model.

Performance Assessment of GNSS-R Polarimetric Observations for Sea Level Monitoring

2021 ◽  
Author(s):  
Mahmoud Rajabi ◽  
Mstafa Hoseini ◽  
Hossein Nahavandchi ◽  
Maximilian Semmling ◽  
Markus Ramatschi ◽  
...  
Keyword(s):  
Time Series ◽  
Circular Polarization ◽  
Sea Level ◽  
Tide Gauge ◽  
Satellite System ◽  
Sea Surface ◽  
Analysis Tool ◽  
Lower Accuracy ◽  
Coastal Sea ◽  
Global Navigation Satellite

<p>Determination and monitoring of the mean sea level especially in the coastal areas are essential, environmentally, and as a vertical datum. Ground-based Global Navigation Satellite System Reflectometry (GNSS-R) is an innovative way which is becoming a reliable alternative for coastal sea-level altimetry. Comparing to traditional tide gauges, GNSS-R can offer different parameters of sea surface, one of which is the sea level. The measurements derived from this technique can cover wider areas of the sea surface in contrast to point-wise observations of a tide gauge.  </p><p>We use long-term ground-based GNSS-R observations to estimate sea level. The dataset includes one-year data from January to December 2016. The data was collected by a coastal GNSS-R experiment at the Onsala space observatory in Sweden. The experiment utilizes three antennas with different polarization designs and orientations. The setup has one up-looking, and two sea-looking antennas at about 3 meters above the sea surface level. The up-looking antenna is Right-Handed Circular Polarization (RHCP). The sea-looking antennas with RHCP and Left-Handed Circular Polarization (LHCP) are used for capturing sea reflected Global Positioning System (GPS) signals. A dedicated reflectometry receiver (GORS type) provides In-phase and Quadrature (I/Q) correlation sums for each antenna based on the captured interferometric signal. The generated time series of I/Q samples from different satellites are analyzed using the Least Squares Harmonic Estimation (LSHE) method. This method is a multivariate analysis tool which can flexibly retrieve the frequencies of a time series regardless of possible gaps or unevenly spaced sampling. The interferometric frequency, which is related to the reflection geometry and sea level, is obtained by LSHE with a temporal resolution of 15 minutes. The sea level is calculated based on this frequency in six modes from the three antennas in GPS L1 and L2 signals.</p><p>Our investigation shows that the sea-looking antennas perform better compared to the up-looking antenna. The highest accuracy is achieved using the sea-looking LHCP antenna and GPS L1 signal. The annual Root Mean Square Error (RMSE) of 15-min GNSS-R water level time series compared to tide gauge observations is 3.7 (L1) and 5.2 (L2) cm for sea-looking LHCP, 5.8 (L1) and 9.1 (L2) cm for sea-looking RHCP, 6.2 (L1) and 8.5 (L2) cm for up-looking RHCP. It is worth noting that the GPS IIR block satellites show lower accuracy due to the lack of L2C code. Therefore, the L2 observations from this block are eliminated.</p>

Sign in / Sign up

Export Citation Format

Share Document