scholarly journals Editorial for “Remote Sensing from Unmanned Aerial Vehicles”

2018 ◽  
Vol 10 (12) ◽  
pp. 1877 ◽  
Author(s):  
William Emery ◽  
John Schmalzel
Keyword(s):  
Remote Sensing ◽  
Unmanned Aerial Vehicles ◽  
Unmanned Aerial Vehicle ◽  
Aerial Vehicles ◽  
Aerial Vehicle ◽  
Remotely Sense

The recent proliferation of unmanned aerial vehicle (UAV) platforms has greatly increased our ability to remotely sense the Earth’s surface from the air at particularly low altitudes. [...]

scholarly journals A Flow Analysis Using a Water Tunnel of an Innovative Unmanned Aerial Vehicle

2021 ◽  
Vol 11 (13) ◽  
pp. 5772
Author(s):  
Dawid Lis ◽  
Adam Januszko ◽  
Tadeusz Dobrocinski
Keyword(s):  
Unmanned Aerial Vehicles ◽  
Unmanned Aerial Vehicle ◽  
Rapid Development ◽  
Lift Coefficient ◽  
Flow Analysis ◽  
Water Tunnel ◽  
Dual Use ◽  
Aerial Vehicles ◽  
Aerial Vehicle ◽  
Technical Construction

The purpose of this article is to present and discuss the results of a non-standard unnamed aerial vehicle construction with a constant cross-section square-shaped avionic profile. Based on the model’s in-air observed maneuverability, the research of avionic construction behavior was carried out in a water tunnel. The results show the model’s specific lift capabilities in comparison to classical avionic constructions. The characteristic results of the lift coefficient showed that the unmanned aerial vehicle presents favorable features than classic avionic constructions. The model was created with the prospect of using it in the future for dual-use purposes, where unmanned aerial vehicles are currently experiencing very rapid development. When creating the prototype, the focus was on low production cost, as well as convenience in operation. The development of this type of breakthrough avionic solution, which shows extraordinary maneuverability, may contribute to increasing the popularity and, above all, the availability of unmanned aerial vehicles for the largest possible group of recipients because of high avionic properties in relation to the technical construction complexity.

METHODS AND MODELS OF QUALITY MANAGEMENT OF MODULAR DESIGN OF ASSEMBLY PRODUCTION OF UNMANNED AERIAL VEHICLES

2021 ◽  
Author(s):  
E. G. Semenova ◽  
◽  
M. I. Bakustina ◽  
Keyword(s):  
Quality Control ◽  
Quality Management ◽  
Unmanned Aerial Vehicles ◽  
Unmanned Aerial Vehicle ◽  
Modular Design ◽  
Aerial Vehicles ◽  
Modern Methods ◽  
Aerial Vehicle ◽  
The Creation ◽  
Assembly Production

The article is devoted to the creation of a method for preparing an unmanned aerial vehicle for implementation as a finished packaged product. To achieve the goal, modern methods of standardization and quality control are used.

Modeling and control of a quadrotor tail-sitter unmanned aerial vehicles

2021 ◽  
pp. 095965182110504
Author(s):  
Hongbo Xin ◽  
Yujie Wang ◽  
Xianzhong Gao ◽  
Qingyang Chen ◽  
Bingjie Zhu ◽  
...  
Keyword(s):  
Control System ◽  
Unmanned Aerial Vehicles ◽  
Unmanned Aerial Vehicle ◽  
Euler Angle ◽  
Level Flight ◽  
Aerial Vehicles ◽  
Flight Mode ◽  
Aerial Vehicle ◽  
Hover Flight ◽  
And Control

The tail-sitter unmanned aerial vehicles have the advantages of multi-rotors and fixed-wing aircrafts, such as vertical takeoff and landing, long endurance and high-speed cruise. These make the tail-sitter unmanned aerial vehicle capable for special tasks in complex environments. In this article, we present the modeling and the control system design for a quadrotor tail-sitter unmanned aerial vehicle whose main structure consists of a traditional quadrotor with four wings fixed on the four rotor arms. The key point of the control system is the transition process between hover flight mode and level flight mode. However, the normal Euler angle representation cannot tackle both of the hover and level flight modes because of the singularity when pitch angle tends to [Formula: see text]. The dual-Euler method using two Euler-angle representations in two body-fixed coordinate frames is presented to couple with this problem, which gives continuous attitude representation throughout the whole flight envelope. The control system is divided into hover and level controllers to adapt to the two different flight modes. The nonlinear dynamic inverse method is employed to realize fuselage rotation and attitude stabilization. In guidance control, the vector field method is used in level flight guidance logic, and the quadrotor guidance method is used in hover flight mode. The framework of the whole system is established by MATLAB and Simulink, and the effectiveness of the guidance and control algorithms are verified by simulation. Finally, the flight test of the prototype shows the feasibility of the whole system.

Trend Analysis of Unmanned Aerial Vehicles (UAVs) Research Published in the HFES Proceedings

2018 ◽  
Vol 62 (1) ◽  
pp. 1067-1071
Author(s):  
Salim A. Mouloua ◽  
James Ferraro ◽  
Mustapha Mouloua ◽  
P.A. Hancock
Keyword(s):  
Human Factors ◽  
Unmanned Aerial Vehicles ◽  
Unmanned Aerial Vehicle ◽  
Supervisory Control ◽  
Research Trends ◽  
Government Agencies ◽  
The Past ◽  
Human Factors And Ergonomics ◽  
Aerial Vehicles ◽  
Aerial Vehicle

The present study was designed to examine the research trends in the literature focusing on Human Factors issues relevant to Unmanned Aerial Vehicle (UAV) systems. As these UAV technologies continue to proliferate with increasing autonomy and supervisory control requirements, it is crucial to evaluate the current and emerging research trends across the generations. This paper reviews the research trends of 228 papers matching our search criteria. The search retained only relevant and complete papers published over the past thirty years (1988-2017) in the Proceedings of the Human Factors and Ergonomics Society. Results were tabulated, graphed, and discussed based on research categories, topic areas, authors’ affiliation, and sources of funding. Results showed a substantial increase in the number of articles in the last two decades, with most papers driven by academic institutions and military and government agencies.

scholarly journals Design and Fabrication of Voice Controlled Unmanned Aerial Vehicle

2016 ◽  
Vol 5 (3) ◽  
pp. 205
Author(s):  
S. Sakthi Anand ◽  
R. Mathiyazaghan
Keyword(s):  
Control System ◽  
Unmanned Aerial Vehicles ◽  
Unmanned Aerial Vehicle ◽  
Voice Recognition ◽  
Search And Rescue ◽  
Voice Input ◽  
Recognition Process ◽  
Aerial Vehicles ◽  
Aerial Vehicle ◽  
The Voice

<p class="Default">Unmanned Aerial Vehicles have gained well known attention in recent years for a numerous applications such as military, civilian surveillance operations as well as search and rescue missions. The UAVs are not controlled by professional pilots and users have less aviation experience. Therefore it seems to be purposeful to simplify the process of aircraft controlling. The objective is to design, fabricate and implement an unmanned aerial vehicle which is controlled by means of voice recognition. In the proposed system, voice commands are given to the quadcopter to control it autonomously. This system is navigated by the voice input. The control system responds to the voice input by voice recognition process and corresponding algorithms make the motors to run at specified speeds which controls the direction of the quadcopter.</p>

Optimized artificial potential field algorithm to multi-unmanned aerial vehicle coordinated trajectory planning and collision avoidance in three-dimensional environment

2019 ◽  
Vol 233 (16) ◽  
pp. 6032-6043 ◽  
Author(s):  
Jun Tang ◽  
Jiayi Sun ◽  
Cong Lu ◽  
Songyang Lao
Keyword(s):  
Unmanned Aerial Vehicles ◽  
Collision Avoidance ◽  
Unmanned Aerial Vehicle ◽  
Trajectory Planning ◽  
Potential Field ◽  
Three Dimensional ◽  
Artificial Potential Field ◽  
Aerial Vehicles ◽  
Aerial Vehicle ◽  
Vehicle Trajectory

Multi-unmanned aerial vehicle trajectory planning is one of the most complex global optimum problems in multi-unmanned aerial vehicle coordinated control. Results of recent research works on trajectory planning reveal persisting theoretical and practical problems. To mitigate them, this paper proposes a novel optimized artificial potential field algorithm for multi-unmanned aerial vehicle operations in a three-dimensional dynamic space. For all purposes, this study considers the unmanned aerial vehicles and obstacles as spheres and cylinders with negative electricity, respectively, while the targets are considered spheres with positive electricity. However, the conventional artificial potential field algorithm is restricted to a single unmanned aerial vehicle trajectory planning in two-dimensional space and usually fails to ensure collision avoidance. To deal with this challenge, we propose a method with a distance factor and jump strategy to resolve common problems such as unreachable targets and ensure that the unmanned aerial vehicle does not collide into the obstacles. The method takes companion unmanned aerial vehicles as the dynamic obstacles to realize collaborative trajectory planning. Besides, the method solves jitter problems using the dynamic step adjustment method and climb strategy. It is validated in quantitative test simulation models and reasonable results are generated for a three-dimensional simulated urban environment.

scholarly journals Active stabilization of unmanned aerial vehicle imaging platform

2020 ◽  
Vol 26 (19-20) ◽  
pp. 1791-1803 ◽  
Author(s):  
Mohit Verma ◽  
Vicente Lafarga ◽  
Mael Baron ◽  
Christophe Collette
Keyword(s):  
Unmanned Aerial Vehicles ◽  
Unmanned Aerial Vehicle ◽  
Vibration Isolation ◽  
Isolation System ◽  
Aerial Vehicles ◽  
Active Stabilization ◽  
Aerial Vehicle ◽  
Active Vibration ◽  
Improved Performance

The advancement in technology has seen a rapid increase in the use of unmanned aerial vehicles for various applications. These unmanned aerial vehicles are often equipped with the imaging platform like a camera. During the unmanned aerial vehicle flight, the camera is subjected to vibrations which hamper the quality of the captured images/videos. The high-frequency vibrations from the unmanned aerial vehicle are transmitted to the camera. Conventionally, passive rubber mounts are used to isolate the camera from the drone vibrations. The passive mounts are able to provide reduction in response near the resonance. However, this comes at the cost of amplification of response at the higher frequency. This article proposes an active vibration isolation system which exhibits improved performance at the higher frequencies than the conventional system. The active isolation system consists of a contact-less voice coil actuator supported by four springs. Experiments are carried out to study the effect of vibrations on the quality of images captured. The characterization of drone vibrations is also carried out by recording the acceleration during different flight modes. The performance of the proposed isolation system is experimentally validated on a real drone camera subjected to the recorded drone acceleration spectrum. The isolation system is found to perform better than the conventional rubber mounts and is able to reduce the vibrations to a factor of one-fourth. It can be effectively used to improve the image acquisition quality of the unmanned aerial vehicles.

scholarly journals Computational optimal launching control for balloon-borne solar-powered unmanned aerial vehicles in near-space

2019 ◽  
Vol 103 (1) ◽  
pp. 003685041987775 ◽  
Author(s):  
Yanpeng Hu ◽  
Yanping Yang ◽  
Xiaoping Ma ◽  
Shu Li
Keyword(s):  
Unmanned Aerial Vehicles ◽  
Unmanned Aerial Vehicle ◽  
Pitch Angle ◽  
Control Variable ◽  
Maximum Speed ◽  
Near Space ◽  
Aerial Vehicles ◽  
Axial Acceleration ◽  
Aerial Vehicle ◽  
Solar Powered

The near-space solar-powered unmanned aerial vehicle has broad prospects in application owing to its high altitude long-endurance performance. Launching solar-powered unmanned aerial vehicle into the near-space with balloon-borne approach has advantages over the traditional sliding take-off methods, in that it is able to quickly and safely cross the turbulent zone. In this article, we investigate the control technology of balloon-borne launching for the solar-powered unmanned aerial vehicles. First, the motion of the launching process is divided into longitudinal and lateral-directional motion, with the longitudinal process and its equation addressed in detail. We then analyze the flight state and restriction conditions that the unmanned aerial vehicle should meet during the process. Second, the target variables and constraints are selected to formulate the optimization problem. The control variable parameterization method is applied to find the optimal pitch angle in the releasing-and-pulling process. More explicitly, a three-channel attitude stabilization controller is designed, in which the longitudinal channel takes the optimal pitch angle as the pitch instruction, the transverse channel carries out the zero control of the inclination angle, and the course channel takes the stabilization control, respectively. Numerical simulation results show that our proposed control design is capable of accelerating the solar-powered unmanned aerial vehicles from the vertical state and pulling them up to the horizontal cruising flight state, with the flight angle of attack, the maximum speed, and the maximum axial acceleration in the pulling process all within the designed range.

scholarly journals Ultra-wideband based cooperative relative localization algorithm and experiments for multiple unmanned aerial vehicles in GPS denied environments

2017 ◽  
Vol 9 (3) ◽  
pp. 169-186 ◽  
Author(s):  
Kexin Guo ◽  
Zhirong Qiu ◽  
Wei Meng ◽  
Lihua Xie ◽  
Rodney Teo
Keyword(s):  
Kalman Filter ◽  
Unmanned Aerial Vehicles ◽  
Unmanned Aerial Vehicle ◽  
Extended Kalman Filter ◽  
Ultra Wideband ◽  
Cooperative Localization ◽  
Relative Localization ◽  
Aerial Vehicles ◽  
Aerial Vehicle ◽  
Displacement Measurements

This article puts forward an indirect cooperative relative localization method to estimate the position of unmanned aerial vehicles (UAVs) relative to their neighbors based solely on distance and self-displacement measurements in GPS denied environments. Our method consists of two stages. Initially, assuming no knowledge about its own and neighbors’ states and limited by the environment or task constraints, each unmanned aerial vehicle (UAV) solves an active 2D relative localization problem to obtain an estimate of its initial position relative to a static hovering quadcopter (a.k.a. beacon), which is subsequently refined by the extended Kalman filter to account for the noise in distance and displacement measurements. Starting with the refined initial relative localization guess, the second stage generalizes the extended Kalman filter strategy to the case where all unmanned aerial vehicles (UAV) move simultaneously. In this stage, each unmanned aerial vehicle (UAV) carries out cooperative localization through the inter-unmanned aerial vehicle distance given by ultra-wideband and exchanging the self-displacements of neighboring unmanned aerial vehicles (UAV). Extensive simulations and flight experiments are presented to corroborate the effectiveness of our proposed relative localization initialization strategy and algorithm.

Development on Fault Detection and Diagnosis of Unmanned Aerial Vehicles

2014 ◽  
Vol 494-495 ◽  
pp. 861-864
Author(s):  
Yi Peng Zhang ◽  
Ke Cai Cao
Keyword(s):  
Fault Detection ◽  
Unmanned Aerial Vehicles ◽  
Unmanned Aerial Vehicle ◽  
State Of The Art ◽  
Fault Detection And Diagnosis ◽  
The Past ◽  
Aerial Vehicles ◽  
Aerial Vehicle ◽  
Detection And Diagnosis

The reliability of unmanned aerial vehicles (UAVs) has caught the attention of many researchers in the past decades. This paper presents a review on the development and important issues of state-of-the-art researches in the field of fault detection and diagnosis (FDD) techniques. Faults on an individual unmanned aerial vehicle or a group of unmanned aerial vehicles are considered for providing an overall picture of fault detection and diagnosis approaches.

Sign in / Sign up

Export Citation Format

Share Document