scholarly journals Design and Validation of a Reduced Switching Components Step-Up Multilevel Inverter (RSCS-MLI)

Processes ◽  
2021 ◽  
Vol 9 (11) ◽  
pp. 1948
Author(s):  
Mohammad Wasiq ◽  
Adil Sarwar ◽  
Zeeshan Sarwer ◽  
Mohd Tariq ◽  
Shafiq Ahmad ◽  
...  
Keyword(s):  
Power Loss ◽  
Output Voltage ◽  
Hardware Implementation ◽  
Harmonic Distortion ◽  
Multilevel Inverter ◽  
Level Control ◽  
Loss Analysis ◽  
Simulation Results ◽  
Insight Into ◽  
Load Conditions

A reduced switching components step-up multilevel inverter (RSCS-MLI) is presented in the paper. The basic circuit of the proposed MLI can produce 11 levels in the output voltage with a reduced number of switching components. The other features of the proposed circuit include a low value of voltage stresses and the inherent generation of the voltage levels pertaining to the negative half without the requirement of an H-bridge. Fundamental frequency switching technique, also known as Nearest Level Control (NLC) technique, is implemented in the proposed topology for generating the switching signals. The experimental total harmonic distortion (THD) in the output voltage comes out to be 9.4% for modulation index equal to 1. Based on different parameters, a comparative study has been shown in the paper, which makes the claim of the proposed MLI stronger. An experimental setup is prepared to carry out the hardware implementation of the proposed structure and monitor its performance under dynamic load conditions, which is also used to verify the simulation results. Power loss analysis, carried out by using PLECS software, helps us to gain insight into different losses occurring while operating the inverter. The different results are explained and analyzed in the paper.

scholarly journals Non-conventional Cascade Multilevel Inverter with Lower Number of Switches by Using Multilevel PWM

2021 ◽  
Vol 17 (1) ◽  
pp. 1-13
Author(s):  
Adala Abdali ◽  
Ali Abdulabbas ◽  
Habeeb Nekad
Keyword(s):  
High Voltage ◽  
High Power ◽  
Power Loss ◽  
Output Voltage ◽  
Lower Number ◽  
Multilevel Inverter ◽  
Three Phase ◽  
Multi Level ◽  
Simulation Results ◽  
Circuit Configuration

The multilevel inverter is attracting the specialist in medium and high voltage applications, among its types, the cascade H bridge Multi-Level Inverter (MLI), commonly used for high power and high voltage applications. The main advantage of the conventional cascade (MLI) is generated a large number of output voltage levels but it demands a large number of components that produce complexity in the control circuit, and high cost. Along these lines, this paper presents a brief about the non-conventional cascade multilevel topologies that can produce a high number of output voltage levels with the least components. The non-conventional cascade (MLI) in this paper was built to reduce the number of switches, simplify the circuit configuration, uncomplicated control, and minimize the system cost. Besides, it reduces THD and increases efficiency. Two topologies of non-conventional cascade MLI three phase, the Nine level and Seventeen level are presented. The PWM technique is used to control the switches. The simulation results show a better performance for both topologies. THD, the power loss and the efficiency of the two topologies are calculated and drawn to the different values of the Modulation index (ma).

Comparison of Switching Angle Arrangement Techniques in Single-Phase Boost Multilevel Inverter for Low-THD Operation

2015 ◽  
Vol 793 ◽  
pp. 167-171
Author(s):  
Mohd Aizuddin Yusof ◽  
Yee Chyan Tan ◽  
M. Othman ◽  
S.S. Lee ◽  
M.A. Roslan ◽  
...  
Keyword(s):  
Output Voltage ◽  
Single Phase ◽  
Harmonic Distortion ◽  
Multilevel Inverter ◽  
Solar Photovoltaic ◽  
Voltage Waveform ◽  
Voltage Level ◽  
Software Simulation ◽  
Multilevel Inverters ◽  
Simulation Results

Multilevel inverters are one of the preferred inverter choices for solar photovoltaic (PV) applications. While these inverters are capable of producing AC staircase output voltage waveform, the total harmonic distortion (THD) of the output voltage waveform can become worse if the switching angle of each voltage level is not carefully chosen. In this paper, four switching angle arrangement techniques are presented and the switching angles generated by these techniques are applied to a new single-phase boost multilevel (SPBM) inverter. The performance of 3-, 5-, 7-, 9-and 11-level SPBM inverter having four different sets of switching angles derived using the aforementioned techniques have been evaluated and compared using PSIM software. Simulation results show that one of the techniques is able to produce an output voltage waveform with the lowest THD, whilst the other generates an output voltage waveform with the highest fundamental voltage component.

scholarly journals A Single Source Switched-Capacitor 13-Level Inverter with Triple Voltage Boosting and Reduced Component Count

Electronics ◽  
2021 ◽  
Vol 10 (19) ◽  
pp. 2321
Author(s):  
Mohammad Tayyab ◽  
Adil Sarwar ◽  
Irfan Khan ◽  
Mohd Tariq ◽  
Md Reyaz Hussan ◽  
...  
Keyword(s):  
Comparative Analysis ◽  
Output Voltage ◽  
Multilevel Inverter ◽  
Switched Capacitor ◽  
Single Source ◽  
Level Control ◽  
Voltage Waveform ◽  
Voltage Level ◽  
Fundamental Cycle ◽  
Simulation Results

A new triple voltage boosting switched-capacitor multilevel inverter (SCMLI) is presented in this paper. It can produce 13-level output voltage waveform by utilizing 12 switches, three diodes, three capacitors, and one DC source. The capacitor voltages are self-balanced as all the three capacitors present in the circuit are connected across the DC source to charge it to the desired voltage level for several instants in one fundamental cycle. A detailed comparative analysis is carried to show the advantages of the proposed topology in terms of the number of switches, number of capacitors, number of sources, total standing voltage (TSV), and boosting of the converter with the recently published 13-level topologies. The nearest level control (NLC)-based algorithm is used for generating switching signals for the IGBTs present in the circuit. The TSV of the proposed converter is 22. Experimental results are obtained for different loading conditions by using a laboratory hardware prototype to validate the simulation results. The efficiency of the proposed inverter is 97.2% for a 200 watt load.

scholarly journals Control of Cascaded H-Bridge Multilevel Inverter Based on Optimum Regulation of Switching Angles, and the FPGA Implementation

2019 ◽  
Vol 3 (1) ◽  
Author(s):  
Hatef Firouzkouhi
Keyword(s):  
Output Voltage ◽  
Harmonic Distortion ◽  
Fpga Implementation ◽  
Multilevel Inverter ◽  
Total Harmonic Distortion ◽  
Switching Pattern ◽  
Multi Level ◽  
Simulation Results ◽  
Polynomial Term

A new concept in control of cascaded H-Bridge multi-level inverters is proposed in this paper. According to this concept, switching angles are considered to be independent from the fundamental voltage. A polynomial term is presented to show the relation between switching angles and DC voltages. Based on this concept, Total Harmonic Distortion (THD) calculations are updated and proved to be independent from the fundamental voltage. Thus, once calculated for minimum THD, the switching pattern can be used for any required level of output voltage. To examine the effectiveness of the proposed method, it is applied in control of an eleven level inverter. The simulation results are demonstrated and verified through experiments with a setup controlled by Xilinx SPARTAN3 family FPGA (XC3S400-PQG208).

Hardware Implementation of Cascaded Hybrid Multilevel Inverter with Reduced Number of Switches

2016 ◽  
Vol 3 (2) ◽  
pp. 314
Author(s):  
Chinnapettai Ramalingam Balamurugan ◽  
S.P. Natarajan ◽  
T.S. Anandhi ◽  
R. Bensaraj
Keyword(s):  
Phase Shift ◽  
Pulse Width ◽  
Output Voltage ◽  
Degrees Of Freedom ◽  
Hardware Implementation ◽  
Pulse Width Modulation ◽  
Multilevel Inverter ◽  
Variable Frequency ◽  
Multi Level ◽  
Simulation Results

<p class="JESTECAbstract">This paper presents the comparison of various multicarrier Pulse Width Modulation (PWM) techniques for the Cascaded Hybrid Multi Level Inverter (CHBMLI). Due to switch combination redundancies, there are certain degrees of freedom to generate the five level AC output voltage. This paper presents the use of Control Freedom Degree (CFD) combination. The effectiveness of the PWM strategies developed using CFD are demonstrated by simulation and experimentation.  The simulation results indicate that the chosen five level inverter triggered by the developed Phase Disposition(PD), Phase Opposition and Disposition(POD), Alternate Phase Opposition and Disposition (APOD), Carrier Overlapping (CO), Phase Shift (PS) and Variable Frequency (VF)<strong> </strong>PWM strategies developed are implemented in real time using FPGA. The simulation and experimental outputs closely match with each other validating the strategies presented.</p>

Hardware Implementation of Solar Based Boost to SEPIC Converter Fed Nine Level Inverter System

2016 ◽  
Vol 7 (4) ◽  
pp. 1031
Author(s):  
D. Jasmine ◽  
M. Gopinath
Keyword(s):  
High Power ◽  
Hardware Implementation ◽  
Harmonic Distortion ◽  
Multilevel Inverter ◽  
Experimental Results ◽  
Pv System ◽  
Multi Level ◽  
Simulation Results ◽  
Fft Analysis

Multi level inverters are widely used in high power applications because of low harmonic distortion. This paper deals with the simulation and implementation of PV based boost to SEPIC converter with multilevel inverter. The output of PV system is stepped up using boost to sepic converter and it is converted into AC using a multilevel inverter. The simulation and experimental results with the R load is presented in this paper. The FFT analysis is done and the THD values are compared. Boost to SEPIC converter is proposed to step up the voltage to the required value. The experimental results are compared with the simulation results. The results indicate that nine level inverter system has better performance than seven level inverter system.

Performance Analysis of a Half Bridge Cell Based Asymmetrical Multilevel Inverter Topology with Minimum Components

2020 ◽  
Vol 13 (4) ◽  
pp. 531-545
Author(s):  
Abeera D. Roy ◽  
Chandrahasan Umayal
Keyword(s):  
Output Voltage ◽  
Harmonic Distortion ◽  
Multilevel Inverter ◽  
Simulation Environment ◽  
Level Control ◽  
Voltage Waveform ◽  
Multilevel Inverters ◽  
Different Types ◽  
Performance Abilities ◽  
Inverter Topology

Background: In Multilevel Inverters (MLI) as the number of level increases, there is a proportionate increase in the count of the semiconductor devices that are employed. Methods: This paper deals with an asymmetrical cascaded H-bridge inverter topology with half bridge cells to produce seven level output voltage waveform. Nearest Level Control (NLM) technique is used to produce the switching pulses. The operating principle of the proposed MLI and its performance abilities is verified through MATLAB/Simulink and a prototype is developed to provide the experimental results. Results: Total Harmonic Distortion (THD) is computed for proposed MLI for different types of loads in simulation environment as well as in the developed hardware prototype. Comparison between the proposed MLI and recent topologies demonstrates the advantageous features. Conclusion: The simulation and hardware results confirm the suitability of the proposed seven level MLI as the total component count, and the requirement of DC sources reduces considerably.

Performance of the Multicarrier Sinusoidal PWM-Based Multilevel Inverter With Reduced Power Loss and Fault Diagnosis Using Wavelets Transformation

2018 ◽  
pp. 353-397 ◽  
Author(s):  
Durga Prasad Garapati ◽  
Jegathesan V. ◽  
Moorthy Veerasamy
Keyword(s):  
Electromagnetic Interference ◽  
Power Loss ◽  
Output Voltage ◽  
Diagnostic Procedure ◽  
Harmonic Distortion ◽  
Voltage Balancing ◽  
Multilevel Inverters ◽  
Wavelets Transform ◽  
Simulation Results ◽  
High Competence

The performances of multilevel inverters (MLIs) are of high competence when compared to the conventional two-level inverters due to reduced harmonic distortions, lower electromagnetic interference, and higher dc link voltages. However, the increased number of components, complex PWM control, and voltage-balancing problem, component failure in the circuit are some of the disadvantages. The topology preferred in this chapter provides a dc voltage in the shape of a staircase which approximates the rectified shape of a commanded sinusoidal wave to the bridge inverter, which in turn alternates the polarity to produce an AC voltage with lesser total harmonic distortion. This topology requires fewer components and hence it leads to a reduction of overall cost and complexity particularly for higher output voltage levels. The component fault diagnostic procedure is developed using wavelets transform tool. Finally, the experimental prototype is developed and validated with the simulation results for different loading conditions.

scholarly journals The multilevel inverter with clamped-diode

2019 ◽  
Vol 14 (3) ◽  
pp. 1189
Author(s):  
Trong-Thang Nguyen
Keyword(s):  
Numerical Simulation ◽  
Circuit Design ◽  
Output Voltage ◽  
Harmonic Distortion ◽  
Control Circuit ◽  
Multilevel Inverter ◽  
Power Circuit ◽  
Advantages And Disadvantages ◽  
Multi Level ◽  
And Control

<p>In this study, the author analyzes the advantages and disadvantages of multi-level inverter compared to the traditional two-level inverter and then chose the suitable inverter. Specifically, the author analyzes and designs the three-level inverter, including the power circuit design and control circuit design. All designs are verified through the numerical simulation on Matlab. The results show that even though the three-level inverter has a low number of switches (only 12 switches), but the quality is very good: the total harmonic distortion is small; the output voltage always follows the reference voltage.</p>

A new three-phase multilevel DC-link inverter topology with reduced switch count for photovoltaic applications

Circuit World ◽  
2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Anbarasan P. ◽  
Krishnakumar V. ◽  
Ramkumar S. ◽  
Venkatesan S.
Keyword(s):  
Power Loss ◽  
Output Voltage ◽  
Pulse Width Modulation ◽  
Harmonic Distortion ◽  
Photovoltaic Cell ◽  
Content Type ◽  
Energy Applications ◽  
Three Phase ◽  
Photovoltaic Applications ◽  
Inverter Topology

Purpose This paper aims to propose a new MLI topology with reduced number of switches for photovoltaic applications. Multilevel inverters (MLIs) have been found to be prospective for renewable energy applications like photovoltaic cell, as they produce output voltage from numerous separate DC sources or capacitor banks with reduced total harmonic distortion (THD) because of a staircase like waveform. However, they endure from serious setbacks including larger number of capacitors, isolated DC sources, associated gate drivers and increased control difficulty for higher number of voltage levels. Design/methodology/approach This paper proposes a new three-phase multilevel DC-link inverter topology overpowering the previously mentioned problems. The proposed topology is designed for five and seven levels in Matlab/Simulink with gating pulse using multicarrier pulse width modulation. The hardware results are shown for a five-level MLI to witness the viability of the proposed MLI for medium voltage applications. Findings The comparison of the proposed topology with other conventional and other topologies in terms of switch count, DC sources and power loss has been made in this paper. The reduction of switches in proposed topology results in reduced power loss. The simulation and hardware show that the output voltage yields a very close sinusoidal voltage and lesser THD. Originality/value The proposed topology can be extended for any level of output voltage which is helpful for sustainable source application.

Sign in / Sign up

Export Citation Format

Share Document