scholarly journals Natural Convection and Entropy Generation of MgO/Water Nanofluids in the Enclosure under a Magnetic Field and Radiation Effects

Processes ◽  
2021 ◽  
Vol 9 (8) ◽  
pp. 1277
Author(s):  
Yacine Khetib ◽  
Ahmad Aziz Alahmadi ◽  
Ali Alzaed ◽  
Ahamd Tahmasebi ◽  
Mohsen Sharifpur ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Entropy Generation ◽  
Radiation Effects ◽  
Volume Fraction ◽  
Numerical Study ◽  
Three Dimensional ◽  
Convection Heat Transfer ◽  
The Other ◽  
Square Enclosure

The authors of the present paper sought to conduct a numerical study on the convection heat transfer, along with the radiation and entropy generation (EGE) of a nanofluids (NFs) in a two and three-dimensional square enclosure, by using the FVM. The enclosure contained a high-temperature blade in the form of a vertical elliptical quadrant in the lower corner of the enclosure. The right edge of the enclosure was kept at low temperature, while the other edges were insulated. The enclosure was subjected to a magnetic field (MGF) and could be adjusted to different angles. In this research, two laboratory relationships dependent on temperature and volume fraction were used to simulate thermal conductivity and viscosity. The variables of this problem were Ra, Ha, RAP, nanoparticle (NP) volume fraction, blade aspect ratio, enclosure angles, and MGF. Evaluating the effects of these variables on heat transfer rate (HTR), EGE, and Be revealed that increasing the Ra and reducing the Ha could increase the HTR and EGE. On the other hand, adding radiation HTR to the enclosure increased the overall HTR. Moreover, an augmentation of the volume fraction of magnesium oxide NPs led to an increased amount of HTR and EGE. Furthermore, any changes to the MGF and the enclosure angle imposed various effects on the HTR. The results indicated that an augmentation of the size of the blade increased and then decreased the HTR and the generated entropy. Finally, increasing the blade always increased the Be.

scholarly journals Three-dimensional numerical study of mixed convection within a ventilated cavity (Shape ‘ L ‘) crossed by a nanofluid under the effect of a magnetic field

2020 ◽  
Vol 307 ◽  
pp. 01027
Author(s):  
S. KHERROUBI ◽  
K. RAGUI ◽  
N. LABSI ◽  
Y.K. BENKAHLA ◽  
A. BOUTRA
Keyword(s):  
Magnetic Field ◽  
Mixed Convection ◽  
Volume Fraction ◽  
Numerical Study ◽  
Vertical Wall ◽  
Three Dimensional ◽  
Convection Heat Transfer ◽  
Left Wall ◽  
Ventilated Cavity ◽  
The Right

The present work is dedicated to the three-dimensional numerical study of mixed convection heat transfer, taking place within a ventilated cavity (of shape L) crossed by Cu-water nanofluid. The enclosure is subjected to the action of a magnetic field. The ventilation is assured by two openings of the same size. The cold flow enters by an opening practiced at the top of the left wall, and exits by another opening practiced at the bottom of the right vertical wall. All the cavity walls are maintained at the same temperature, superior to that of the entering flow, except the side walls which are considered as adiabatic. The control parameters are: the Reynolds number and the Hartmann number as well as the nanoparticles volume fraction.

scholarly journals Numerical Simulation of the Natural Convection with Presence of the Nanofluids in Cubical Cavity

2020 ◽  
Vol 2020 ◽  
pp. 1-17
Author(s):  
Mohamed Sannad ◽  
Abourida Btissam ◽  
Belarche Lahoucine
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Volume Fraction ◽  
Numerical Study ◽  
Three Dimensional ◽  
Convection Heat Transfer ◽  
Flow And Heat Transfer ◽  
Heating Section ◽  
The Right

This article consists of a numerical study of natural convection heat transfer in three-dimensional cavity filled with nanofluids. This configuration is heated by a partition maintained at a hot constant and uniform temperature TH. The right and left vertical walls are kept at a cold temperature TC while the rest is adiabatic. The fluid flow and heat transfer in the cavity are studied for different sets of the governing parameters, namely, the nanofluid type, the Rayleigh number Ra = 103, 104, 105, and 106, and the volume fraction Ф varying between Ф = 0 and 0.1. The obtained results show a positive effect of the volume fraction and the Rayleigh number on the heat transfer improvement. The analysis of the results related to the heat transfer shows that the copper-based nanofluid guarantees the best thermal transfer. In addition, the increase of the heating section size and Ra leads to an increased amount of heat. Similarly, increasing the volume fraction improves the intensification of the flow and increases the heat exchange.

Numerical Study on Mixed Convection and Entropy Generation of a Nanofluid in a Lid-Driven Square Enclosure

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
R. K. Nayak ◽  
S. Bhattacharyya ◽  
I. Pop
Keyword(s):  
Heat Transfer ◽  
Mixed Convection ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Numerical Study ◽  
Control Volume ◽  
Transport Equations ◽  
Bejan Number ◽  
Square Enclosure ◽  
Wide Range

A numerical investigation of mixed convection due to a copper–water nanofluid in an enclosure is presented. The mixed convection is governed by moving the upper lid of the enclosure and imposing a vertical temperature gradient. The transport equations for fluid and heat are modeled by using the Boussinesq approximation. A modified form of the control volume based SIMPLET algorithm is used for the solution of the transport equations. The fluid flow and heat transfer characteristics are studied for a wide range of Reynolds number and Grashof number so as to have the Richardson number greater or less than 1. The nanoparticle volume fraction is considered up to 20%. Heat flow patterns are analyzed through the energy flux vector. The rate of enhancement in heat transfer due to the addition of nanoparticles is analyzed. The entropy generation and Bejan number are evaluated to demonstrate the thermodynamic optimization of the mixed convection. We have obtained the enhancement rate in heat transfer and entropy generation in nanofluid for a wide range of parameter values.

Numerical Study of Magnetic Field Effects on Buoyancy Driven Convection in a Non-Isothermally Heated Square Enclosure

2011 ◽  
Vol 312-315 ◽  
pp. 536-541
Author(s):  
Ghanbar Ali Sheikhzadeh ◽  
Mohsen Pirmohammadi ◽  
A. Fattahi ◽  
M.A. Mehrabian
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Hartmann Number ◽  
Numerical Study ◽  
Convection Heat Transfer ◽  
Magnetic Field Effects ◽  
Left Wall ◽  
Square Enclosure ◽  
The Right ◽  
Sinusoidal Function

Numerical simulation of natural convection heat transfer in the presence of a magnetic field is analyzed in a non-isothermally heated square enclosure. The left wall is heated and cooled with a sinusoidal heat source and the right wall is cooled isothermally. The horizontal walls of the enclosure are adiabatic. The effects of Rayleigh number (Ra = 104, 105 and 106), Hartmann number (Ha = 0, 25, 50 and 100) and amplitude of sinusoidal function (n = 0.25, 0.5 and 1) on temperature and flow fields are analyzed. It is observed that the rate of heat transfer is decreased with increasing the Hartmann number; it is also decreased when decreasing the amplitude of sinusoidal function.

Numerical Simulation of Heat Transfer in Laminar Natural Convection of Mixed Newtonian-Non-Newtonian and Pure Non-Newtonian Nanofluids in a Square Enclosure

2021 ◽  
pp. 1-44
Author(s):  
Ajay Vallabh ◽  
P.S. Ghoshdastidar
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Base Fluid ◽  
Volume Fraction ◽  
Numerical Study ◽  
Transfer Model ◽  
Nanoparticle Concentration ◽  
Left Wall ◽  
Square Enclosure ◽  
First Case

Abstract This paper presents a steady-state heat transfer model for the natural convection of mixed Newtonian-Non-Newtonian (Alumina-Water) and pure Non-Newtonian (Alumina-0.5 wt% Carboxymethyl Cellulose (CMC)/Water) nanofluids in a square enclosure with adiabatic horizontal walls and isothermal vertical walls, the left wall being hot and the right wall cold. In the first case the nanofluid changes its Newtonian character to Non-Newtonian past 2.78% volume fraction of the nanoparticles. In the second case the base fluid itself is Non-Newtonian and the nanofluid behaves as a pure Non-Newtonian fluid. The power-law viscosity model has been adopted for the non-Newtonian nanofluids. A finite-difference based numerical study with the Stream function-Vorticity-Temperature formulation has been carried out. The homogeneous flow model has been used for modelling the nanofluids. The present results have been extensively validated with earlier works. In Case I the results indicate that Alumina-Water nanofluid shows 4% enhancement in heat transfer at 2.78% nanoparticle concentration. Following that there is a sharp decline in heat transfer with respect to that in base fluid for nanoparticle volume fractions equal to and greater than 3%. In Case II Alumina-CMC/Water nanofluid shows 17% deterioration in heat transfer with respect to that in base fluid at 1.5% nanoparticle concentration. An enhancement in heat transfer is observed for increase in hot wall temperature at a fixed volume fraction of nanoparticles, for both types of nanofluid.

scholarly journals Natural convection in a differentially heated enclosure with triangular roof

1970 ◽  
Vol 39 (1) ◽  
pp. 1-7 ◽  
Author(s):  
Sumon Saha ◽  
Noman Hasan ◽  
Chowdhury Md Feroz
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Fluid Flow ◽  
Natural Convection ◽  
Average Nusselt Number ◽  
Numerical Study ◽  
Convection Heat Transfer ◽  
Element Analysis ◽  
Left Wall ◽  
Square Enclosure

A numerical study has been carried out for laminar natural convection heat transfer within a two-dimensional modified square enclosure having a triangular roof. The vertical sidewalls are differentially heated considering a constant flux heat source strip is flush mounted with the left wall. The opposite wall is considered isothermal having a temperature of the surrounding fluid. The rest of the walls are adiabatic. Air is considered as the fluid inside the enclosure. The solution has been carried out on the basis of finite element analysis by a non-linear parametric solver to examine the heat transfer and fluid flow characteristics. Different heights of the triangular roof have been considered for the present analysis. Fluid flow fields and isotherm patterns and the average Nusselt number are presented for the Rayleigh numbers ranging from 103 to 106 in order to show the effects of these governing parameters. The average Nusselt number computed for the case of isoflux heating is also compared with the case of isothermal heating as available in the literature. The outcome of the present investigation shows that the convective phenomenon is greatly influenced by the inclined roof height. Keywords: Natural convection, triangular roof, Rayleigh number, isoflux heating. Doi:10.3329/jme.v39i1.1826 Journal of Mechanical Engineering, vol. ME39, No. 1, June 2008 1-7

Magnetohydrodynamic effects on flow structures and heat transfer over two cylinders wrapped with a porous layer in side

2016 ◽  
Vol 26 (5) ◽  
pp. 1416-1432 ◽  
Author(s):  
Saman Rashidi ◽  
Javad Abolfazli Esfahani ◽  
Mohammad Sadegh Valipour ◽  
Masoud Bovand ◽  
Ioan Pop
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Flow Field ◽  
Porous Layer ◽  
Numerical Study ◽  
Convection Heat Transfer ◽  
Circular Cylinders ◽  
Flow Structures ◽  
Content Type ◽  
The Magnetic Field

Purpose – The analysis of the flow field and heat transfer around a tube row or tube banks wrapped with porous layer have many related engineering applications. Examples include the reactor safety analysis, combustion, compact heat exchangers, solar power collectors, high-performance insulation for buildings and many another applications. The purpose of this paper is to perform a numerical study on flows passing through two circular cylinders in side-by-side arrangement wrapped with a porous layer under the influence of a magnetic field. The authors focus the attention to the effects of magnetic field, Darcy number and pitch ratio on the mechanism of convection heat transfer and flow structures. Design/methodology/approach – The Darcy-Brinkman-Forchheimer model for simulating the flow in porous medium along with the Maxwell equations for providing the coupling between the flow field and the magnetic field have been used. Equations with the relevant boundary conditions are numerically solved using a finite volume approach. In this study, Stuart and Darcy numbers are varied within the range of 0 < N < 3 and 1e-6 < Da < 1e-2, respectively, and Reynolds and Prandtl numbers are equal to Re=100 and Pr=0.71, respectively. Findings – The results show that the drag coefficient decreases for N < 0.6 and increases for N > 0.6. Also, the effect of magnetic field is negligible in the gap between two cylinders because the magnetic field for two cylinders counteracts each other in these regions. Originality/value – To the authors knowledge, in the open literature, flow passing over two circular cylinders in side-by-side arrangement wrapped with a porous layer has been rarely investigated especially under the influence of a magnetic field.

Fluid flow and heat transfer of a stratified system during natural convection – influence of chamfered corners

2019 ◽  
Vol 29 (2) ◽  
pp. 470-486 ◽  
Author(s):  
Alireza Rahimi ◽  
Aravindhan Surendar ◽  
Aygul Z. Ibatova ◽  
Abbas Kasaeipoor ◽  
Emad Hasani Malekshah
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Natural Convection ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Three Dimensional ◽  
Immiscible Fluids ◽  
Content Type ◽  
Flow And Heat Transfer

Purpose This paper aims to investigate the three-dimensional natural convection and entropy generation in the rectangular cuboid cavities included by chamfered triangular partition made by polypropylene. Design/methodology/approach The enclosure is filled by multi-walled carbon nanotubes (MWCNTs)-H2O nanofluid and air as two immiscible fluids. The finite volume approach is used for computation. The fluid flow and heat transfer are considered with combination of local entropy generation due to fluid friction and heat transfer. Moreover, a numerical method is developed based on three-dimensional solution of Navier–Stokes equations. Findings Effects of side ratio of triangular partitions (SR = 0.5, 1 and 2), Rayleigh number (103 < Ra < 105) and solid volume fraction (f = 0.002, 0.004 and 0.01 Vol.%) of nanofluid are investigated on both natural convection characteristic and volumetric entropy generation. The results show that the partitions can be a suitable method to control fluid flow and energy consumption, and three-dimensional solutions renders more accurate results. Originality/value The originality of this work is to study the three-dimensional natural convection and entropy generation of a stratified system.

Sign in / Sign up

Export Citation Format

Share Document