scholarly journals Effects of Micro-Tab on the Lift Enhancement of Airfoil S-809 with Trailing-Edge Flap

Processes ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 547
Author(s):  
Jianjun Ye ◽  
Shehab Salem ◽  
Juan Wang ◽  
Yiwen Wang ◽  
Zonggang Du ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Flow Behavior ◽  
Air Flow ◽  
Lift Coefficient ◽  
Pressure Coefficient ◽  
Turbine Blades ◽  
Lower Surface ◽  
Wind Turbine Blades ◽  
Trailing Edge ◽  
Trailing Edge Flap

Recently, the Trailing-Edge Flap with Micro-Tab (TEF with Micro-Tab) has been exploited to enhance the performance of wind turbine blades. Moreover, it can also be used to generate more lift and delay the onset of stall. This study focused mostly on the use of TEF with Micro-Tab in wind turbine blades using NREL’s S-809 as a model airfoil. In particular, the benefits generated by TEF with Micro-Tab may be of great interest in the design of wind turbine blades. In this paper, an attempt was made to evaluate the influence of TEF with Micro-Tab on the performance of NREL’s S-809 airfoils. Firstly, a computational fluid dynamics (CFD) model for the airfoil NREL’s S-809 was established, and validated by comparison with previous studies and wind tunnel experimental data. Secondly, the effects of the flap position (H) and deflection angle (αF) on the flow behaviors were investigated. As a result, the effect of TEF on air-flow behavior was demonstrated by augmenting the pressure coefficient at the lower surface of the airfoil at flap position 80% chord length (C) and αF = 7.5°. Thirdly, the influence of TEF with Micro-Tab on the flow behaviors of the airfoil NREL’s S-809 was studied and discussed. Different Micro-Tab positions and constant TEF were examined. Finally, the effects of TEF with Micro-Tab on the aerodynamic characteristics of the S-809 with TEF were compared. The results showed that an increase in the maximum lift coefficient by 25% and a delay in the air-flow stall were accomplished due to opposite sign vortices, which was better than the standard airfoil and S-809 with TEF. Therefore, it was deduced that the benefits of TEF with Micro-Tab were apparent, especially at the lower surface of the airfoil. This particularly suggests that the developed model could be used as a new trend to modify the designs of wind turbine blades.

scholarly journals Bionic Design of Wind Turbine Blade Based on Long-Eared Owl’s Airfoil

2017 ◽  
Vol 2017 ◽  
pp. 1-10 ◽  
Author(s):  
Weijun Tian ◽  
Zhen Yang ◽  
Qi Zhang ◽  
Jiyue Wang ◽  
Ming Li ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Lift Coefficient ◽  
Turbine Blades ◽  
Lower Surface ◽  
Aerodynamic Characteristics ◽  
Wind Turbine Blade ◽  
Wind Turbine Blades ◽  
Bionic Design ◽  
Bionic Blade

The main purpose of this paper is to demonstrate a bionic design for the airfoil of wind turbines inspired by the morphology of Long-eared Owl’s wings. Glauert Model was adopted to design the standard blade and the bionic blade, respectively. Numerical analysis method was utilized to study the aerodynamic characteristics of the airfoils as well as the blades. Results show that the bionic airfoil inspired by the airfoil at the 50% aspect ratio of the Long-eared Owl’s wing gives rise to a superior lift coefficient and stalling performance and thus can be beneficial to improving the performance of the wind turbine blade. Also, the efficiency of the bionic blade in wind turbine blades tests increases by 12% or above (up to 44%) compared to that of the standard blade. The reason lies in the bigger pressure difference between the upper and lower surface which can provide stronger lift.

Active load control for wind turbine blades using trailing edge flap

2013 ◽  
Vol 16 (3) ◽  
pp. 263-278 ◽  
Author(s):  
Jong-Won Lee ◽  
Joong-Kwan Kim ◽  
Jae-Hung Han ◽  
Hyung-Kee Shin
Keyword(s):  
Wind Turbine ◽  
Turbine Blades ◽  
Load Control ◽  
Wind Turbine Blades ◽  
Trailing Edge ◽  
Active Load ◽  
Trailing Edge Flap

scholarly journals Deep dynamic stall and active aerodynamic modification on a S833 airfoil using pitching trailing edge flap

2020 ◽  
pp. 0309524X2093885
Author(s):  
Farid Samara ◽  
David A Johnson
Keyword(s):  
Wind Turbine ◽  
Turbine Blades ◽  
Hysteresis Loops ◽  
Bending Moment ◽  
Dynamic Stall ◽  
Wind Turbine Blades ◽  
Trailing Edge ◽  
Load Fluctuation ◽  
Trailing Edge Flaps ◽  
Trailing Edge Flap

Due to the dynamic nature of the wind resource, wind turbine blades are subjected to significant variation in flow parameters, such as the angle of attack ([Formula: see text]). In some cases, the occurrence of dynamic stall on wind turbine blades causes load fluctuation which leads to material fatigue that tends to decrease the life span of the blades. In this study, the influence of a trailing edge flap on dynamic stall effects is investigated at high [Formula: see text] typical of wind turbines but atypical elsewhere. Pitching of the trailing edge flap was found to have a significant impact on the dynamic stall hysteresis loops responsible for the load fluctuation. Frequency analysis showed that the trailing edge flap was capable of reducing the cyclic fluctuation in the coefficient of lift and root bending moment by at least 26% and 24%, respectively. These results are a significant contribution toward understanding the advantages of using trailing edge flaps and how implementing them will reduce wind turbine blade load fluctuations.

Experimental investigations of flow over NACA airfoils 0021 and 4412 of wind turbine blades with and without Tubercles

2021 ◽  
pp. 0309524X2110071
Author(s):  
Usman Butt ◽  
Shafqat Hussain ◽  
Stephan Schacht ◽  
Uwe Ritschel
Keyword(s):  
Wind Tunnel ◽  
Drag Coefficient ◽  
Wind Turbine ◽  
Critical Region ◽  
Lift Coefficient ◽  
Turbine Blades ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Experimental Investigations ◽  
Wind Turbine Blades

Experimental investigations of wind turbine blades having NACA airfoils 0021 and 4412 with and without tubercles on the leading edge have been performed in a wind tunnel. It was found that the lift coefficient of the airfoil 0021 with tubercles was higher at Re = 1.2×105 and 1.69×105 in post critical region (at higher angle of attach) than airfoils without tubercles but this difference relatively diminished at higher Reynolds numbers and beyond indicating that there is no effect on the lift coefficients of airfoils with tubercles at higher Reynolds numbers whereas drag coefficient remains unchanged. It is noted that at Re = 1.69×105, the lift coefficient of airfoil without tubercles drops from 0.96 to 0.42 as the angle of attack increases from 15° to 20° which is about 56% and the corresponding values of lift coefficient for airfoil with tubercles are 0.86 and 0.7 at respective angles with18% drop.

Analysis of Blunt Trailing Edge Airfoils

2003 ◽  
Author(s):  
K. J. Standish ◽  
C. P. van Dam
Keyword(s):  
Experimental Data ◽  
Wind Turbine ◽  
Turbine Blades ◽  
Navier Stokes ◽  
Computational Techniques ◽  
Wind Turbine Blades ◽  
Trailing Edge ◽  
Blunt Trailing Edge ◽  
Large Wind ◽  
Structural Volume

The adoption of blunt trailing edge airfoils for the inner regions of large wind turbine blades has been proposed. Blunt trailing edge airfoils would not only provide increased structural volume, but have also been found to improve the lift characteristics of airfoils and therefore allow for section shapes with a greater maximum thickness. Limited experimental data makes it difficult for wind turbine designers to consider and conduct tradeoff studies using these section shapes. This lack of experimental data precipitated the present analysis of blunt trailing edge airfoils using computational fluid dynamics. Several computational techniques are applied including a viscous/inviscid interaction method and several Reynolds-averaged Navier-Stokes methods.

Experimental study of a pitching and plunging wing

2018 ◽  
Vol 90 (7) ◽  
pp. 1136-1144 ◽  
Author(s):  
Dimitris Gkiolas ◽  
Demetri Yiasemides ◽  
Demetri Mathioulakis
Keyword(s):  
Experimental Data ◽  
Flow Visualization ◽  
Wind Turbine ◽  
Flow Separation ◽  
Flow Behavior ◽  
Lift Coefficient ◽  
Turbine Blades ◽  
Content Type ◽  
Separation Line ◽  
Wing Chord

Purpose The complex flow behavior over an oscillating aerodynamic body, e.g. a helicopter rotor blade, a rotating wind turbine blade or the wing of a maneuvering airplane involves combinations of pitching and plunging motions. As the parameters of the problem (Re, St and phase difference between these two motions) vary, a quasi-steady analysis fails to provide realistic results for the aerodynamic response of the moving body, whereas this study aims to provide reliable experimental data. Design/methodology/approach In the present study, a pitching and plunging mechanism was designed and built in a subsonic closed-circuit wind tunnel as well as a rectangular aluminum wing of a 2:1 aspect-ratio with a NACA64-418 airfoil, used in wind turbine blades. To measure the pressure distribution along the wing chord, a number of fast responding transducers were embedded into the mid span wing surface. Simultaneous pressure measurements were conducted along the wing chord for the Reynolds number of 0.85 × 106 for both steady and unsteady cases (pitching and plunging). A flow visualization technique was used to detect the flow separation line under steady conditions. Findings Elevated pressure fluctuations coincide with the flow separation line having been detected through surface flow visualization and flattened pressure distributions appear downstream of the flow separation line. Closed hysteresis loops of the lift coefficient versus angle of attack were measured for combined pitching and plunging motions. Practical implications The experimental data can be used for improvement of unsteady fluid mechanics problem solvers. Originality/value In the present study, a new installation was built allowing the aerodynamic study of oscillating wings performing pitching and plunging motions with prescribed frequencies and phase lags between the two motions. The experimental data can be used for improvement of computational fluid dynamics codes in case that the examined aerodynamic body is oscillating.

Wind Tunnel Experimental Study of Wind Turbine Airfoil Aerodynamic Characteristics

2012 ◽  
Vol 260-261 ◽  
pp. 125-129
Author(s):  
Xin Zi Tang ◽  
Xu Zhang ◽  
Rui Tao Peng ◽  
Xiong Wei Liu
Keyword(s):  
Wind Tunnel ◽  
Wind Turbine ◽  
Lift Coefficient ◽  
Turbine Blades ◽  
Aerodynamic Characteristics ◽  
Wind Turbine Blades ◽  
High Lift ◽  
Minimum Drag ◽  
Stall Angle ◽  
High Reynolds

High lift and low drag are desirable for wind turbine blade airfoils. The performance of a high lift airfoil at high Reynolds number (Re) for large wind turbine blades is different from that at low Re number for small wind turbine blades. This paper investigates the performance of a high lift airfoil DU93-W-210 at high Re number in low Re number flows through wind tunnel testing. A series of low speed wind tunnel tests were conducted in a subsonic low turbulence closed return wind tunnel at the Re number from 2×105to 5×105. The results show that the maximum lift, minimum drag and stall angle differ at different Re numbers. Prior to the onset of stall, the lift coefficient increases linearly and the slope of the lift coefficient curve is larger at a higher Re number, the drag coefficient goes up gradually as angle of attack increases for these low Re numbers, meanwhile the stall angle moves from 14° to 12° while the Re number changes from 2×105to 5×105.

scholarly journals Numerical Analysis of Wind Turbine Airfoil Aerodynamic Performance with Leading Edge Bump

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Majid Asli ◽  
Behnam Mashhadi Gholamali ◽  
Abolghasem Mesgarpour Tousi
Keyword(s):  
Wind Turbine ◽  
Control Method ◽  
Flow Behavior ◽  
Renewable Energy Sources ◽  
Lift Coefficient ◽  
Turbine Blades ◽  
Vortex Generator ◽  
Leading Edge ◽  
Suction Side ◽  
Aerodynamic Performance

Aerodynamic performance improvement of wind turbine blade is the key process to improve wind turbine performance in electricity generated and energy conversion in renewable energy sources concept. The flow behavior on wind turbine blades profile and the relevant phenomena like stall can be improved by some modifications. In the present paper, Humpback Whales flippers leading edge protuberances model as a novel passive stall control method was investigated on S809 as a thick airfoil. The airfoil was numerically analyzed by CFD method in Reynolds number of 106and aerodynamic coefficients in static angle of attacks were validated with the experimental data reported by Somers in NREL. Therefore, computational results for modified airfoil with sinusoidal wavy leading edge were presented. The results revealed that, at low angles of attacks before the stall region, lift coefficient decreases slightly rather than baseline model. However, the modified airfoil has a smooth stall trend while baseline airfoil lift coefficient decreases sharply due to the separation which occurred on suction side. According to the flow physics over the airfoils, leading edge bumps act as vortex generator so vortices containing high level of momentum make the flow remain attached to the surface of the airfoil at high angle of attack and prevent it from having a deep stall.

Sign in / Sign up

Export Citation Format

Share Document