scholarly journals Numerical Investigation of a Portable Incinerator: A Parametric Study

Processes ◽  
2020 ◽  
Vol 8 (8) ◽  
pp. 923
Author(s):  
Mohsen Saffari Pour ◽  
Ali Hakkaki-Fard ◽  
Bahar Firoozabadi
Keyword(s):  
Flow Rate ◽  
Fossil Fuels ◽  
Combustion Process ◽  
Critical Parameters ◽  
Mesh Quality ◽  
Hazardous Gases ◽  
Computational Fluid Dynamics Cfd ◽  
Reliable Design ◽  
Cooling Air ◽  
Numerical Approaches

The application of incinerators for the municipal solid waste (MSW) is growing due to the ability of such instruments to produce energy and, more specifically, reduce waste volume. In this paper, a numerical simulation of the combustion process with the help of the computational fluid dynamics (CFD) inside a portable (mobile) incinerator has been proposed. Such work is done to investigate the most critical parameters for a reliable design of a domestic portable incinerator, which is suitable for the Iranian food and waste culture. An old design of a simple incinerator has been used to apply the natural gas (NG), one of the available cheap fossil fuels in Iran. After that, the waste height, place of the primary burner, and the flow rate of the cooling air inside the incinerator, as the main parameters of the design, are investigated. A validation is also performed for the mesh quality test and the occurrence of the chemical reactions near the burner of the incinerator. Results proved that the numerical results have less than 5% error compared to the previous experimental and numerical approaches. In addition, results show that by moving the primary burner into the secondary chamber of the incinerator, the temperature and the heating ability of the incinerator could be affected dramatically. Moreover, it has been found that by increasing the flow rate of the cooling air inside the incinerator to some extent, the combustion process is improved and, on the other hand, by introducing more cooling air, the evacuation of the hazardous gases from the exhaust is also improved.

scholarly journals Fundamentals and Principles of Solid-State Electrochemical Sensors for High Temperature Gas Detection

Catalysts ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 1
Author(s):  
Elena Gorbova ◽  
Fotini Tzorbatzoglou ◽  
Costas Molochas ◽  
Dimitris Chloros ◽  
Anatoly Demin ◽  
...  
Keyword(s):  
Gas Sensors ◽  
Fossil Fuels ◽  
Electrochemical Sensors ◽  
Renewable Energy Sources ◽  
Rapid Development ◽  
Combustion Process ◽  
Environmental Issues ◽  
Oxygen Ion ◽  
Hazardous Gases ◽  
Combustion Processes

The rapid development of science, technology, and engineering in the 21st century has offered a remarkable rise in our living standards. However, at the same time, serious environmental issues have emerged, such as acid rain and the greenhouse effect, which are associated with the ever-increasing need for energy consumption, 85% of which comes from fossil fuels combustion. From this combustion process, except for energy, the main greenhouse gases-carbon dioxide and steam-are produced. Moreover, during industrial processes, many hazardous gases are emitted. For this reason, gas-detecting devices, such as electrochemical gas sensors able to analyze the composition of a target atmosphere in real time, are important for further improving our living quality. Such devices can help address environmental issues and inform us about the presence of dangerous gases. Furthermore, as non-renewable energy sources run out, there is a need for energy saving. By analyzing the composition of combustion emissions of automobiles or industries, combustion processes can be optimized. This review deals with electrochemical gas sensors based on solid oxide electrolytes, which are employed for the detection of hazardous gasses at high temperatures and aggressive environments. The fundamentals, the principle of operation, and the configuration of potentiometric, amperometric, combined (amperometric-potentiometric), and mixed-potential gas sensors are presented. Moreover, the results of previous studies on carbon oxides (COx), nitrogen oxides (NOx), hydrogen (H2), oxygen (O2), ammonia (NH3), and humidity (steam) electrochemical sensors are reported and discussed. Emphasis is given to sensors based on oxygen ion and proton-conducting electrolytes.

SCIENTIFIC AND ENGINEERING PRINCIPLES OF EFFICIENT FUEL USE AND ENVIRONMENTALLY FRIENDLY GAS COMBUSTION IN STOVE PLATES. PART 1. MODERN STATE-OF-THE-ART AND DIRECTIONS FOR IMPROVEMENT THE GAS BURNING IN DOMESTIC GAS COOKERS

2017 ◽  
pp. 3-18 ◽  
Author(s):  
B.S. Soroka ◽  
V.V. Horupa
Keyword(s):  
Natural Gas ◽  
Flow Rate ◽  
Gas Flow ◽  
Renewable Energy Sources ◽  
Combustion Process ◽  
Orifice Diameter ◽  
Firing Process ◽  
Gas Flow Rate ◽  
Gas Combustion ◽  
Gas Stoves

Natural gas NG consumption in industry and energy of Ukraine, in recent years falls down as a result of the crisis in the country’s economy, to a certain extent due to the introduction of renewable energy sources along with alternative technologies, while in the utility sector the consumption of fuel gas flow rate enhancing because of an increase the number of consumers. The natural gas is mostly using by domestic purpose for heating of premises and for cooking. These items of the gas utilization in Ukraine are already exceeding the NG consumption in industry. Cooking is proceeding directly in the living quarters, those usually do not meet the requirements of the Ukrainian norms DBN for the ventilation procedures. NG use in household gas stoves is of great importance from the standpoint of controlling the emissions of harmful components of combustion products along with maintenance the satisfactory energy efficiency characteristics of NG using. The main environment pollutants when burning the natural gas in gas stoves are including the nitrogen oxides NOx (to a greater extent — highly toxic NO2 component), carbon oxide CO, formaldehyde CH2O as well as hydrocarbons (unburned UHC and polyaromatic PAH). An overview of environmental documents to control CO and NOx emissions in comparison with the proper norms by USA, EU, Russian Federation, Australia and China, has been completed. The modern designs of the burners for gas stoves are considered along with defining the main characteristics: heat power, the natural gas flow rate, diameter of gas orifice, diameter and spacing the firing openings and other parameters. The modern physical and chemical principles of gas combustion by means of atmospheric ejection burners of gas cookers have been analyzed from the standpoints of combustion process stabilization and of ensuring the stability of flares. Among the factors of the firing process destabilization within the framework of analysis above mentioned, the following forms of unstable combustion/flame unstabilities have been considered: flashback, blow out or flame lifting, and the appearance of flame yellow tips. Bibl. 37, Fig. 11, Tab. 7.

Extraction and Determination of Physico-chemical Properties of Oil from Watermelon Seeds (Citrullus lanatus L) to Use in Internal Combustion Engines

2017 ◽  
Vol 68 (11) ◽  
pp. 2676-2681
Author(s):  
Mihaela Gabriela Dumitru ◽  
Dragos Tutunea
Keyword(s):  
Fatty Acid ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Citrullus Lanatus ◽  
Combustion Process ◽  
Chemical Properties ◽  
Physico Chemical ◽  
Mean Diameter ◽  
Geometrical Mean ◽  
Reduction Of Nox

The purpose of this work was to investigate the physicochemical properties of watermelon seeds and oil and to find out if this oil is suitable and compatible with diesel engines. The results showed that the watermelon seeds had the maximum length (9.08 mm), width (5.71mm), thickness (2.0 mm), arithmetic mean diameter (5.59 mm), geometrical mean diameter (4.69 mm), sphericity (51.6%), surface area (69.07), volume 0.17 cm3 and moisture content 5.4%. The oil was liquid at room temperature, with a density and refractive index of 0.945 and 1.4731 respectively acidity value (1.9 mgNaOH/g), free fatty acid (0.95 mgNaOH), iodine value (120 mgI2/100g), saponification value (180 mgKOH/g), antiradical activity (46%), peroxide value (7.5 mEqO2/Kg), induction period (6.2 h), fatty acid: palmitic acid (13.1%), stearic acid (9.5 %), oleic acid (15.2 %) and linoleic acid (61.3%). Straight non food vegetable oils can offer a solution to fossil fuels by a cleaner burning with minimal adaptation of the engine. A single cylinder air cooled diesel engine Ruggerini RY 50 was used to measure emissions of various blends of watermelon oil (WO) and diesel fuel (WO10D90, WO20D80, WO30D70 and WO75D25). The physic-chemical properties of the oil influence the combustion process and emissions leading to the reduction of NOX and the increase in CO, CO2 and HC.

scholarly journals Dependence of the Flue Gas Flow on the Setting of the Separation Baffle in the Flue Gas Tract

2021 ◽  
Vol 11 (7) ◽  
pp. 2961
Author(s):  
Nikola Čajová Kantová ◽  
Alexander Čaja ◽  
Marek Patsch ◽  
Michal Holubčík ◽  
Peter Ďurčanský
Keyword(s):  
Particulate Matter ◽  
Flue Gas ◽  
Gas Flow ◽  
Negative Impact ◽  
Combustion Process ◽  
Cfd Simulations ◽  
Piv Measurements ◽  
Computational Fluid Dynamics Cfd ◽  
Particle Imaging ◽  
Combustion Of Solid Fuels

With the combustion of solid fuels, emissions such as particulate matter are also formed, which have a negative impact on human health. Reducing their amount in the air can be achieved by optimizing the combustion process as well as the flue gas flow. This article aims to optimize the flue gas tract using separation baffles. This design can make it possible to capture particulate matter by using three baffles and prevent it from escaping into the air in the flue gas. The geometric parameters of the first baffle were changed twice more. The dependence of the flue gas flow on the baffles was first observed by computational fluid dynamics (CFD) simulations and subsequently verified by the particle imaging velocimetry (PIV) method. Based on the CFD results, the most effective is setting 1 with the same boundary conditions as those during experimental PIV measurements. Setting 2 can capture 1.8% less particles and setting 3 can capture 0.6% less particles than setting 1. Based on the stoichiometric calculations, it would be possible to capture up to 62.3% of the particles in setting 1. The velocities comparison obtained from CFD and PIV confirmed the supposed character of the turbulent flow with vortexes appearing in the flue gas tract, despite some inaccuracies.

Effect of pre-swirl nozzle closure modes on unsteady flow and heat transfer characteristics in a pre-swirl system of aero-engine

2021 ◽  
pp. 095441002110191
Author(s):  
Gaowen Liu ◽  
Zhao Lei ◽  
Aqiang Lin ◽  
Qing Feng ◽  
Yan Chen
Keyword(s):  
Heat Transfer ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Temperature Drop ◽  
Thermodynamic Characteristics ◽  
Circumferential Direction ◽  
Temperature Changes ◽  
Air Supply ◽  
Cooling Air

The pre-swirl system is of great importance for temperature drop and cooling air supply. This study aims to investigate the influencing mechanism of heat transfer, nonuniform thermodynamic characteristics, and cooling air supply sensitivity in a pre-swirl system by the application of the flow control method of the pre-swirl nozzle. A novel test rig was proposed to actively control the supplied cooling air mass flow rate by three adjustable pre-swirl nozzles. Then, the transient problem of the pre-swirl system was numerically conducted by comparison with 60°, 120°, and 180° rotating disk cavity cases, which were verified with the experiment results. Results show that the partial nozzle closure will aggravate the fluctuation of air supply mass flow rate and temperature. When three parts of nozzles are closed evenly at 120° in the circumferential direction, the maximum value of the nonuniformity coefficient of air supply mass flow rate changes to 3.1% and that of temperature changes to 0.25%. When six parts of nozzles are closed evenly at 60° in the circumferential direction, the maximum nonuniformity coefficient of air supply mass flow rate changes to 1.4% and that of temperature changes to 0.20%. However, different partial nozzle closure modes have little effect on the average air supply parameters. Closing 14.3% of the nozzle area will reduce the air supply mass flow rate by 9.9% and the average air supply temperature by about 1 K.

scholarly journals Simulation of Thermal Effects on the Flow Field in a Pilot-Scale Kiln

2021 ◽  
Author(s):  
I. A. Sofia Larsson ◽  
Anna-Lena Ljung ◽  
B. Daniel Marjavaara
Keyword(s):  
Flow Field ◽  
Coal Combustion ◽  
Thermal Effects ◽  
Iron Ore ◽  
Combustion Process ◽  
Pilot Scale ◽  
Mixing Properties ◽  
Process Gas ◽  
Mixing Rates ◽  
Computational Fluid Dynamics Cfd

AbstractThe flow field and coal combustion process in a pilot-scale iron ore pelletizing kiln is simulated using a computational fluid dynamics (CFD) model. The objective of the work is to investigate how the thermal effects from the flame affect the flow field. As expected, the combustion process with the resulting temperature rise and volume expansion leads to an increase of the velocity in the kiln. Apart from that, the overall flow field looks similar regardless of whether combustion is present or not. The flow field though affects the combustion process by controlling the mixing rates of fuel and air, governing the flame propagation. This shows the importance of correctly predicting the flow field in this type of kiln, with a large amount of process gas circulating, in order to optimize the combustion process. The results also justify the use of down-scaled, geometrically similar, water models to investigate kiln aerodynamics in general and mixing properties in particular. Even if the heat release from the flame is neglected, valuable conclusions regarding the flow field can still be drawn.

Modeling of Compressor Drum Cavities With Radial Inflow

2016 ◽  
Author(s):  
D. Amirante ◽  
Z. Sun ◽  
J. W. Chew ◽  
N. J. Hills ◽  
N. R. Atkins
Keyword(s):  
Thermal Stratification ◽  
Turbulence Modeling ◽  
Navier Stokes ◽  
Inflow Rate ◽  
Cfd Models ◽  
Flow And Heat Transfer ◽  
Rotating Discs ◽  
Computational Fluid Dynamics Cfd ◽  
Inlet Conditions ◽  
Cooling Air

Reynolds-Averaged Navier-Stokes (RANS) computations have been conducted to investigate the flow and heat transfer between two co-rotating discs with an axial throughflow of cooling air and a radial bleed introduced from the shroud. The computational fluid dynamics (CFD) models have been coupled with a thermal model of the test rig, and the predicted metal temperature compared with the thermocouple data. CFD solutions are shown to vary from a buoyancy driven regime to a forced convection regime, depending on the radial inflow rate prescribed at the shroud. At a high radial inflow rate, the computations show an excellent agreement with the measured temperatures through a transient rig condition. At a low radial inflow rate, the cavity flow is destabilized by the thermal stratification. Good qualitative agreement with the measurements is shown, although a significant over-prediction of disc temperatures is observed. This is associated with under prediction of the penetration of the axial throughflow into the cavity. The mismatch could be the result of strong sensitivity to the prescribed inlet conditions, in addition to possible shortcomings in the turbulence modeling.

Effect of Active Modulation of Through-Casing Coolant Injection on Turbine Efficiency

2017 ◽  
Author(s):  
Brian M. T. Tang ◽  
Marko Bacic ◽  
Peter T. Ireland
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Total Pressure ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Turbine Efficiency ◽  
Coolant Injection ◽  
Cooling Air

This paper presents a computational investigation into the impact of cooling air injected through the stationary over-tip turbine casing on overall turbine efficiency. The high work axial flow turbine is representative of the high pressure turbine of a civil aviation turbofan engine. The effect of active modulation of the cooling air is assessed, as well as that of the injection locations. The influence of the through-casing coolant injection on the turbine blade over-tip leakage flow and the associated secondary flow features are examined. Transient (unsteady) sliding mesh simulations of a one turbine stage rotor-stator domain are performed using periodic boundary conditions. Cooling air configurations with a constant total pressure air supply, constant mass flow rate and actively controlled total pressure supply are assessed for a single geometric arrangement of cooling holes. The effects of both the mass flow rate of cooling air and the location of its injection relative to the turbine rotor blade are examined. The results show that all of the assessed cooling configurations provided a benefit to turbine row efficiency of between 0.2 and 0.4 percentage points. The passive and constant mass flow rate configurations reduced the over-tip leakage flow, but did so in an inefficient manner, with decreasing efficiency observed with increasing injection mass flow rate beyond 0.6% of the mainstream flow, despite the over-tip leakage mass flow rate continuing to reduce. By contrast, the active total pressure controlled injection provided a more efficient manner of controlling this leakage flow, as it permitted a redistribution of cooling air, allowing it to be applied in the regions close to the suction side of the blade tip which more directly reduced over-tip leakage flow rates and hence improved efficiency. Cooling air injected close to the pressure side of the rotor blade was less effective at controlling the leakage flow, and was associated with increased aerodynamic loss in the passage vortex.

Heat Transfer and Pressure Drop in a Converging Pedestal Array With Exit Area Variation

2018 ◽  
Author(s):  
L. W. Soma ◽  
F. E. Ames ◽  
S. Acharya
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Rate ◽  
Film Cooling ◽  
Reynolds Numbers ◽  
Flow Path ◽  
Internal Cooling ◽  
Channel Measurements ◽  
Trailing Edge ◽  
Cooling Air

The trailing edge of a vane is one of the most difficult areas to cool due to a narrowing flow path, high external heat transfer rates, and deteriorating external film cooling protection. Converging pedestal arrays are often used as a means to provide internal cooling in this region. The thermally induced stresses in the trailing edge region of these converging arrays have been known to cause failure in the pedestals of conventional solidity arrays. The present paper documents the heat transfer and pressure drop through two high solidity converging rounded diamond pedestal arrays. These arrays have a 45 percent pedestal solidity. One array which was tested has nine rows of pedestals with an exit area in the last row consistent with the convergence. The other array has eight rows with an expanded exit in the last row to enable a higher cooling air flow rate. The expanded exit of the eight row array allows a 30% increase in the coolant flow rate compared with the nine row array for the same pressure drop. Heat transfer levels correlate well based on local Reynolds numbers but fall slightly below non converging arrays. The pressure drop across the array naturally increases toward the trailing edge with the convergence of the flow passage. A portion of the cooling air pressure drop can be attributed to acceleration while a portion can be attributed to flow path losses. Detailed array static pressure measurements provide a means to develop a correlation for the prediction of pressure drop across the cooling channel. Measurements have been acquired over Reynolds numbers based on exit flow conditions and the characteristic pedestal length scale ranging from 5000 to over 70,000.

scholarly journals Effect of hydraulic and geometric factors upon leakage flow rate in pressurized pipes

RBRH ◽  
2021 ◽  
Vol 26 ◽  
Author(s):  
Mayara Francisca da Silva ◽  
Fábio Veríssimo Gonçalves ◽  
Johannes Gérson Janzen
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Rate ◽  
Leakage Flow ◽  
Cfd Simulations ◽  
Mean Velocity ◽  
Leakage Flow Rate ◽  
Geometric Factors ◽  
Leakage Area ◽  
Computational Fluid Dynamics Cfd

ABSTRACT Computational Fluid Dynamics (CFD) simulations of a leakage in a pressurized pipe were undertaken to determine the empirical effects of hydraulic and geometric factors on the leakage flow rate. The results showed that pressure, leakage area and leakage form, influenced the leakage flow rate significantly, while pipe thickness and mean velocity did not influence the leakage flow rate. With relation to the interactions, the effect of pressure upon leakage flow rate depends on leakage area, being stronger for great leakage areas; the effects of leakage area and pressure on leakage flow rate is more pronounced for longitudinal leakages than for circular leakages. Finally, our results suggest that the equations that predict leakage flow rate in pressurized pipes may need a revision.

Sign in / Sign up

Export Citation Format

Share Document