scholarly journals Spark Plasma Sintering of Cobalt Powders in Conjunction with High Energy Mechanical Treatment and Nanomodification

Processes ◽  
2020 ◽  
Vol 8 (5) ◽  
pp. 627
Author(s):  
Van Minh Nguyen ◽  
Rita Khanna ◽  
Yuri Konyukhov ◽  
Tien Hiep Nguyen ◽  
Igor Burmistrov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Spark Plasma Sintering ◽  
Bending Strength ◽  
High Energy ◽  
Fine Grained ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Microstructure Density ◽  
High Degree ◽  
Grain Boundary Movement

Spark plasma sintering (SPS) investigations were carried out on three sets of Co specimens: untreated, high energy mechanically (HEMT) pre-treated, and nanomodified powders. The microstructure, density, and mechanical properties of sintered pellets were investigated as a function of various pre-treatments and sintering temperatures (700–1000 °C). Fine-grained sinters were obtained for pre-treated Co powders; nano-additives tended to inhibit grain growth by reinforcing particles at grain boundaries and limiting grain-boundary movement. High degree of compaction was also achieved with relative densities of sintered Co pellets ranging between 95.2% and 99.6%. A direct co-relation was observed between the mechanical properties and densities of sintered Co pellets. For a comparable sinter quality, sintering temperatures for pre-treated powders were lower by 100 °C as compared to untreated powders. Highest values of bending strength (1997 MPa), microhardness (305 MPa), and relative density (99.6%) were observed for nanomodified HEMT and SPS processed Co pellets, sintered at 700 °C.

scholarly journals Mechanical Milling-Assisted Spark Plasma Sintering of Fine-Grained W-Ni-Mn Alloy

Materials ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1323 ◽  
Author(s):  
Yanlin Pan ◽  
Daoping Xiang ◽  
Ning Wang ◽  
Hui Li ◽  
Zhishuai Fan
Keyword(s):  
Spark Plasma Sintering ◽  
Mechanical Milling ◽  
Bending Strength ◽  
Sintering Temperature ◽  
Interface Fracture ◽  
Composite Powders ◽  
Fine Grained ◽  
Plasma Sintering ◽  
Binding Phase ◽  
Spark Plasma

Fine-grained W-6Ni-4Mn alloys were fabricated by spark plasma sintering (SPS) using mechanical milling W, Ni and Mn composite powders. The relative density of W-6Ni-4Mn alloy increases from 71.56% to 99.60% when it is sintered at a low temperature range of 1000–1200 °C for 3 min. The spark plasma sintering process of the alloy can be divided into three stages, which clarify the densification process of powder compacts. As the sintering temperature increases, the average W grain size increases but remains at less than 7 µm and the distribution of the binding phase is uniform. Transmission electron microscopy (TEM) observation reveals that the W-6Ni-4Mn alloy consists of the tungsten phase and the γ-(Ni, Mn, W) binding phase. As the sintering temperature increases, the Rockwell hardness and bending strength of alloys initially increases and then decreases. The optimum comprehensive hardness and bending strength of the alloy are obtained at 1150 °C. The main fracture mode of the alloys is W/W interface fracture.

Enhanced Mechanical Properties of SiCw/ SiCp-Reinforced Mg Composites Fabricated by Spark Plasma Sintering

2021 ◽  
Vol 878 ◽  
pp. 83-88
Author(s):  
Hideaki Tsukamoto ◽  
Chang Sun
Keyword(s):  
Mechanical Properties ◽  
Melting Point ◽  
Spark Plasma Sintering ◽  
Bending Strength ◽  
Oxide Layers ◽  
Plasma Sintering ◽  
Spark Plasma

This study aims to fabricate SiC whisker (w)/ particle (p)-reinforced magnesium (Mg) composites with enhanced mechanical properties using spark plasma sintering (SPS) methods. It has been confirmed that dispersing state of SiCw can be improved by addition of SiCp. However, due to presence of voids and cracks between the oxide layers, surrounding SiCw/p, and Mg matrix in the composites, SiCw with SiCp cannot contribute to enhance the bending strength of Mg matrix. This issue can be tackled by adding low melting point metals such as Sn into the composites to fill the defects in the composites.

Enhancing Mechanical Properties of Various Sintered Pellets with Nano-Additives

2021 ◽  
Vol 410 ◽  
pp. 62-67
Author(s):  
Tien Hiep Nguyen ◽  
Yury V. Konyukhov ◽  
Van Minh Nguyen
Keyword(s):  
Mechanical Properties ◽  
Spark Plasma Sintering ◽  
Bending Strength ◽  
Size Range ◽  
Pressureless Sintering ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Nano Additives ◽  
Free Spaces ◽  
The Impact

The impact of Fe, Co, Ni nano-additives on the density, microhardness and bending strength was investigated for several sintered pellets. Fe, Co, Ni nanopowders (NP) were prepared in the size range 67-94 nm using chemical metallurgy techniques. These powders (0.5 wt. %) were dispersed into three sets of micron powders: Co (+0.5 wt. % Co NP); Fe (+0.5 wt. % Fe NP); Fe+0.5wt. % C (+0.5 wt. % Co and 0.5 wt. % Ni NP). Mixtures were further mixed and processed using a magnetic mill and a turbulent mixer. Sintering was carried out using spark plasma sintering (SPS) as well as pressureless sintering (PS). The densities of sintered pellets were found to increase by 2.5-3% (SPS) and 3-5% (PS) in the presence of nano-additives; corresponding increases in microhardness and bending strength were determined to be 7.9-11.1% and 17.9-38.7%, respectively. These results are discussed in terms enhanced packing due to interparticle sliding and the filling of free spaces with the nanodisperse phase.

Fabrication of TiAl Intermetallic by Spark Plasma Sintering

2007 ◽  
Vol 336-338 ◽  
pp. 1050-1052 ◽  
Author(s):  
Hai Tao Wu ◽  
Yun Long Yue ◽  
Wei Bing Wu ◽  
Hai Yan Yin
Keyword(s):  
Mechanical Properties ◽  
Intermetallic Compounds ◽  
Spark Plasma Sintering ◽  
Bending Strength ◽  
Sintering Temperature ◽  
Three Point Bending ◽  
The Poor ◽  
High Relative Density ◽  
Plasma Sintering ◽  
Spark Plasma

The γ-TiAl intermetallic compounds were produced at the temperature ranging from 850°C to 1050°C by the Spark Plasma Sintering (SPS) process. The effects of sintering temperature and holding time on the mechanical properties of γ-TiAl intermetallic compounds were investigated. The γ-TiAl intermetallic compounds sintered at 1050°C for 10 min showed a high relative density more than 98%, and had the best three-point bending strength of 643MPa, fracture toughness of 12 MPa·m1/2 and microhardness of 560MPa. The microstructural observations indicated typical characteristics of intergranular fracture, which meant the poor ductility of γ-TiAl intermetallic compounds.

Sign in / Sign up

Export Citation Format

Share Document