scholarly journals Near-Wall Flow Characteristics of a Centrifugal Impeller with Low Specific Speed

Processes ◽  
2019 ◽  
Vol 7 (8) ◽  
pp. 514 ◽  
Author(s):  
Weidong Cao ◽  
Zhixiang Jia ◽  
Qiqi Zhang
Keyword(s):  
Relative Velocity ◽  
Flow Characteristics ◽  
Suction Side ◽  
Centrifugal Impeller ◽  
Wall Region ◽  
Pressure Side ◽  
Region Flow ◽  
Low Specific Speed ◽  
Specific Speed ◽  
Near Wall

In order to study the near-wall region flow characteristics in a low-specific-speed centrifugal impeller, based on ANSYS-CFX 15.0 software, Reynolds averaged Navier-Stokes (RANS) methods and renormalization group (RNG) k-ɛ turbulence model were used to simulate the whole flow field of a low specific speed centrifugal pump with five blades under different flow rates. Simulation results of external characteristics of the pump were in good agreement with experimental results. Profiles were set on the pressure side and suction side of impeller blades at the distances of 0.5 mm and 2 mm, respectively, to study the distributions of flow characteristics near the wall region of five groups of blades. The results show that the near-wall region flow characteristics of five groups of blades were similar, but the static pressure, relative velocity, cross flow velocity, and turbulent kinetic energy of profiles on the pressure side were quite different to those on the suction sides, and these characteristics also changed with the alternation of flow rate. As the flow rate was 13 m3/h or 20 m3/h, within the radius range of 40 to 50 mm, there was an extent of negative relative velocity of the profiles on the pressure side, and a counter-current happened not on the suction side, but on the pressure side in the low specific speed centrifugal impeller. The flow characteristics of profiles at the distances of 0.5 mm and 2 mm also showed a small difference.

An Experimental Investigation of Flow Characteristics Downstream of Discrete Film Cooling Holes on Turbine Blade Leading Edge

2011 ◽  
Vol 383-390 ◽  
pp. 5553-5560
Author(s):  
Shao Hua Li ◽  
Hong Wei Qu ◽  
Mei Li Wang ◽  
Ting Ting Guo
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Flow Characteristics ◽  
Leading Edge ◽  
Suction Side ◽  
Wall Region ◽  
Pressure Side ◽  
Blowing Ratio ◽  
Curvature Gradient ◽  
Film Cooling Holes

The gas turbine blade was studied on the condition that the mainstream velocity was 10m/s and the Renolds number based on the chord length of the blade was 160000.The Hot-film anemometer was used to measure the two-dimension speed distribution along the downstream of the film cooling holes on the suction side and the pressure side. The conclusions are as follows: When the blowing ratio of the suction side and the pressure side increasing, the the mainstream and the jet injection mixing center raising. Entrainment flow occurs at the position where the blade surface with great curvature gradient, simultaneously the mixing flow has a wicked adhere to the wall. The velocity gradient of the u direction that on the suction side increase obviously, also the level of the wall adherence is better than the pressure side. With the x/d increasing, the velocity u that on the pressure side gradually become irregularly, also the secondary flow emerged near the wall region where the curvature is great. The blowing ratio on the suction side has a little influence on velocity v than that on the pressure side.

scholarly journals Effects of the outlet position of splitter blade on the flow characteristics in low-specific-speed centrifugal pump

2018 ◽  
Vol 10 (7) ◽  
pp. 168781401878952 ◽  
Author(s):  
Jinfeng Zhang ◽  
Guidong Li ◽  
Jieyun Mao ◽  
Shouqi Yuan ◽  
Yefei Qu ◽  
...  
Keyword(s):  
Centrifugal Pump ◽  
Pressure Coefficient ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Suction Side ◽  
Trailing Edge ◽  
Pressure Surface ◽  
Low Specific Speed ◽  
Specific Speed ◽  
Good Agreement

To elucidate the influences of the outlet position of splitter blades on the performance of a low-specific-speed centrifugal pump, two different splitter blade schemes were proposed: one located in the middle of the channel and the other having a deviation angle at the trailing edge of splitter blade toward the suction side of the main blade. Experiments on the model pump with different splitter blade schemes were conducted, and numerical simulations on internal flow characteristics in the impellers were studied by means of the shear stress transport k- ω turbulence model. The results suggest that there is a good agreement between the experimental and numerical results. The splitter blade schemes can effectively optimize the structure of the jet-wake pattern and improve the internal flow states in the impeller channel. In addition, the secondary flow and inlet circulation on the pressure surface of main blade, the flow separation on the suction side of splitter blade, the pressure coefficient distributions on blade surface can achieve an evident amelioration when the trailing edge of splitter blade toward the suction side of the main blade is mounted at an appropriate position.

Effects of short blades on performance and inner flow characteristics of a low-specific-speed centrifugal pump

2017 ◽  
Vol 231 (4) ◽  
pp. 290-302 ◽  
Author(s):  
Can Kang ◽  
Ning Mao ◽  
Chen Pan ◽  
Yang Zhu ◽  
Bing Li
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuations ◽  
Flow Characteristics ◽  
Low Flow ◽  
Back Surface ◽  
Flow Rates ◽  
Pump Operation ◽  
Low Specific Speed ◽  
Specific Speed

A low-specific-speed centrifugal pump equipped with long and short blades is studied. Emphasis is placed on the pump performance and inner flow characteristics at low flow rates. Each short blade is intentionally shifted towards the back surface of the neighboring long blade, and the outlet parts of the short blades are uniformly shortened. Unsteady numerical simulation is conducted to disclose inner flow patterns associated with the modified design. Thereby, a comparison is enabled between the two schemes featured by different short blades. Both practical operation data and numerical results support that the deviation and cutting of the short blades can eliminate the positive slope of pump head curve at low flow rates. Therefore, the modification of short blades improves the pump operation stability. Due to the shortening of the outlet parts of the short blades, velocity distributions between impeller outlet and radial diffuser inlet exhibit explicitly altered circumferential flow periodicity. Pressure fluctuations in the radial diffuser are complex in terms of diversified periodicity and amplitudes. Flow rate influences pressure fluctuations in the radial diffuser considerably. As flow rate decreases, the regularity of the orbit of hydraulic loads exerted upon the impeller collapses while hydraulic loads exerted upon the short blades remain circumferentially periodic.

Experimental Study on Film Cooling Flow Characteristics of Turbine Stator Blade at Different Setting Angles

2012 ◽  
Vol 614-615 ◽  
pp. 592-595
Author(s):  
Ling Zhang ◽  
Hai Rui Dong ◽  
Guo Liang Wen
Keyword(s):  
Film Cooling ◽  
Effective Means ◽  
Turbine Blades ◽  
Flow Characteristics ◽  
Suction Side ◽  
Pressure Side ◽  
Blowing Ratio ◽  
Turbine Stator ◽  
Setting Angle ◽  
Stator Blade

The technology of film cooling is one of the most effective means of protecting the turbine blades. In this paper, flow structures of the turbine stator blade with six hole-rows at different blowing ratio（M=0.5, 1.0 and 1.5）and setting angles（β=40°, 50°, 60°, 70°, 80° and 90°） was measured by PIV in piston flow type of low-speed wind tunnel laboratory. Velocity was analyzed. Results show that: velocity gradient of suction side was much higher than pressure side and increased with setting angle reduction; Adherence of film is influenced by setting angle and blowing ratio, when M=1.0 and β=70° anchorage dependent is best and suction side is greater than pressure side.

Numerical Study on Heat Transfer and Flow Characteristics in Double Turning Areas Ribbed Serpentine Channel With Lateral Outflow

2019 ◽  
Author(s):  
Bo-lun Zhang ◽  
Hui-ren Zhu ◽  
Tao Guo ◽  
Chun-yi Yao ◽  
Zhong-yi Fu
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Numerical Study ◽  
Pressure Coefficient ◽  
Flow Characteristics ◽  
Suction Side ◽  
Pressure Side ◽  
Maximum Increase ◽  
Serpentine Channel ◽  
Ratio Condition

Abstract The double turning areas ribbed serpentine channel with lateral outflow is an important structure for designing the internal systems of turbine blade. The current work similarly simplifies the internal channel of the real blade. The Nusselt number and pressure coefficient distribution of the double turning areas ribbed serpentine channel with different outflow ratios are numerically researched under static and rotating conditions. The Realizable k-ε turbulence model with enhanced wall treatment is used in the numerical simulation. The inlet Reynolds number is 11000. The rotation numbers vary from 0 to 0.09. Three outflow ratios are 27%/0%/73%, 27%/49%/24% and 27%/73%/0%, respectively. The rotation radius (R) is 46.4d. The result shows that the Nusselt number distribution of the passage 3 under 27%/49%/24% outflow ratio condition is similar to that under 27%/73%/0% outflow ratio condition. There is a large low Nusselt number area in the passage 3 under Dr = 27%/0%/73% condition. The averaged area Nusselt number ratios on the suction side of the passage 1, passage 2 and passage 3 are higher than that on the pressure side under nonrotating condition. Rotation enhances heat transfer on the suction side of the passage 2, and has a positive effect on pressure side heat transfer of passage 1 and passage 3. The averaged area Nusselt number ratio of passage 3 under 27%/73%/0% outflow ratio condition is higher than that under other outflow ratio conditions. With the rotation number increasing, the pressure coefficient of the complete ribbed serpentine channel gradually increases, and the maximum increase is in the first turning area.

Investigation of the Wake Effect From the Centrifugal Splitter Impeller Blade to the Vaned Diffuser

2012 ◽  
Author(s):  
Xuechen Li ◽  
Guang Xi ◽  
Jiang Hua ◽  
Wuqi Gong
Keyword(s):  
Flow Characteristics ◽  
Suction Side ◽  
Wake Flow ◽  
Centrifugal Impeller ◽  
Wake Effect ◽  
Impeller Blade ◽  
Vaned Diffuser ◽  
Side Pressure ◽  
Unsteady Wake ◽  
Impeller Outlet

In this paper, the unsteady wake effect from an unshrouded centrifugal impeller with splitter blades was numerically and experimentally investigated. The numerical simulated detail flow characteristics of two stations, respectively placed at the impeller outlet and the diffuser inlet, were compared with the measured data. The “jet-wake” flow pattern was observed at the exit of the impeller. And the investigation showed that the wake effect of the splitter was weaker that of the main blade. But both the main blade and the splitter blade wake could affect the diffuser performance at a range of whole-chord length and they provoked the pressure side profile pressure fluctuating intensely from 10% chord to 50% chord, while the suction side pressure varying rapidly at the range from 60% chord to 80% chord.

D41 Design and internal flow characteristics of low specific speed diagonal flow fan

2007 ◽  
Vol 2007.60 (0) ◽  
pp. 143-144
Author(s):  
Kousuke NISHIDA ◽  
Kenji KANEKO ◽  
Yoichi KINOUE ◽  
Norimasa SHIOMI
Keyword(s):  
Flow Characteristics ◽  
Internal Flow ◽  
Low Specific Speed ◽  
Specific Speed

Study of gaseous velocity slip in nano-channel using molecular dynamics simulation

2014 ◽  
Vol 24 (6) ◽  
pp. 1338-1347 ◽  
Author(s):  
Fubing Bao ◽  
Zhihong Mao ◽  
Limin Qiu
Keyword(s):  
Molecular Dynamics ◽  
Gas Flow ◽  
Interaction Strength ◽  
Flow Characteristics ◽  
Velocity Slip ◽  
Dynamics Simulation ◽  
Wall Region ◽  
Content Type ◽  
Slip Phenomenon ◽  
Near Wall

Purpose – The purpose of this paper is to investigate the gas flow characteristics in near wall region and the velocity slip phenomenon on the wall in nano-channels based on the molecular dynamics simulation. Design/methodology/approach – An external gravity force was employed to drive the flow. The density and velocity profiles across the channel, and the velocity slip on the wall were studied, considering different gas temperatures and gas-solid interaction strengths. Findings – The simulation results demonstrate that a single layer of gas molecules is adsorbed on wall surface. The density of adsorption layer increases with the decrease of gas temperature and with increase of interaction strength. The near wall region extents several molecular diameters away from the wall. The density profile is flatter at higher temperature and the velocity profile has the traditional parabolic shape. The velocity slip on the wall increases with the increase of temperature and with decrease of interaction strength linearly. The average velocity decreases with the increase of gas-solid interaction strength. Originality/value – This research presents gas flow characteristics in near wall region and the velocity slip phenomenon on the wall in nano-channels. Some interesting results in nano-scale channels are obtained.

Sign in / Sign up

Export Citation Format

Share Document