scholarly journals Crystallization Behavior and Electrical Properties of Nanoparticle-Reinforced Poly(lactic Acid)-Based Films

Polymers ◽  
2022 ◽  
Vol 14 (1) ◽  
pp. 177
Author(s):  
Mei-Xian Li ◽  
Yu Ren ◽  
Dasom Lee ◽  
Sung-Woong Choi
Keyword(s):  
Electrical Conductivity ◽  
Lactic Acid ◽  
Electrical Properties ◽  
Crystallization Behavior ◽  
Hydrolytic Degradation ◽  
Poly Lactic Acid ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Multiwalled Carbon ◽  
Degradation Behaviors

Graphene oxide (GO) and multiwalled carbon nanotubes with silver particles (MWNT-Ag) of different concentrations were used as nanofillers to prepare poly(lactic acid) (PLA) nanoparticle films through the solvent casting method. In this study, the effects of nanoparticles on the crystallization behavior, relationships between the dispersion and electrical properties, and hydrolytic degradation behaviors were investigated for the PLA/MWNT-Ag and PLA/rGO films. Differential scanning calorimetry was used to evaluate the crystallization behaviors of the PLA/MWNT-Ag and PLA/reduced GO (rGO) films. Electron probe microanalysis was performed to characterize the dispersion of MWNT-Ag, and X-ray diffraction and Raman spectroscopy were used to determine the degree of dispersion of rGO in the PLA matrix. The results showed that nanoparticles enhanced the crystallization kinetics of PLA as well as the hydrolytic degradation rate. From the measurement of electrical properties, the electrical conductivity of PLA/MWNT-Ag 1.0 wt% was much higher than that of the pure PLA and PLA/rGO films, showing that MANT and Ag nanoparticles contribute greatly to enhancing the electrical conductivity of the PLA/MWNT-Ag films.

Crystallization Properties of Nucleated Poly(lactic acid)

2012 ◽  
Vol 549 ◽  
pp. 322-326 ◽  
Author(s):  
Yong Chen ◽  
Qiang Dou
Keyword(s):  
Lactic Acid ◽  
Crystallization Behavior ◽  
Polarized Light ◽  
Nucleating Agent ◽  
Poly Lactic Acid ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Crystallization Properties ◽  
Melting And Crystallization

The effect of a nucleating agent (NT-C) on the crystallization behavior of poly(lactic acid) (PLA) was studied. The melting and crystallization behavior and spherulitic morphology of the nucleated PLA were investigated by means of differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD) and polarized light microscopy (PLM). It is found that the crystallization temperature and crystallinity increase, the spherulitic size decrease for the nucleated PLA. But the crystal structure of the nucleated PLA is not changed.

scholarly journals Relationship between the Stereocomplex Crystallization Behavior and Mechanical Properties of PLLA/PDLA Blends

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1851
Author(s):  
Hye-Seon Park ◽  
Chang-Kook Hong
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Crystallization Behavior ◽  
Mechanical Analysis ◽  
X Ray Diffraction ◽  
Nucleation Agent ◽  
Scanning Calorimetry ◽  
Nucleation Sites ◽  
Wide Range ◽  
Degree Of Crystallization

Poly (l-lactic acid) (PLLA) is a promising biomedical polymer material with a wide range of applications. The diverse enantiomeric forms of PLLA provide great opportunities for thermal and mechanical enhancement through stereocomplex formation. The addition of poly (d-lactic acid) (PDLA) as a nucleation agent and the formation of stereocomplex crystallization (SC) have been proven to be an effective method to improve the crystallization and mechanical properties of the PLLA. In this study, PLLA was blended with different amounts of PDLA through a melt blending process and their properties were calculated. The effect of the PDLA on the crystallization behavior, thermal, and mechanical properties of PLLA were investigated systematically by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction (XRD), polarized optical microscopy (POM), dynamic mechanical analysis (DMA), and tensile test. Based on our findings, SC formed easily when PDLA content was increased, and acts as nucleation sites. Both SC and homo crystals (HC) were observed in the PLLA/PDLA blends. As the content of PDLA increased, the degree of crystallization increased, and the mechanical strength also increased.

scholarly journals Hemp Fibre Reinforced Poly(Lactic Acid) Composites

2007 ◽  
Vol 29-30 ◽  
pp. 337-340 ◽  
Author(s):  
M.A. Sawpan ◽  
K.L. Pickering ◽  
Alan Fernyhough
Keyword(s):  
Lactic Acid ◽  
Degree Of Crystallinity ◽  
Poly Lactic Acid ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Hemp Fibre ◽  
Reinforcing Material ◽  
Fibre Loading ◽  
The Degree Of Crystallinity

The potential of hemp fibre as a reinforcing material for Poly(lactic acid) (PLA) was investigated. Good interaction between hemp fibre and PLA resulted in increases of 100% for Young’s modulus and 30% for tensile strength of composites containing 30 wt% fibre. Different predictive ‘rule of mixtures’ models (e.g. Parallel, Series and Hirsch) were assessed regarding the dependence of tensile properties on fibre loading. Limited agreement with models was observed. Differential scanning calorimetry (DSC) and x-ray diffraction (XRD) studies showed that hemp fibre increased the degree of crystallinity in PLA composites.

scholarly journals Composites Based on Poly(Lactic Acid) (PLA) and SBA-15: Effect of Mesoporous Silica on Thermal Stability and on Isothermal Crystallization from Either Glass or Molten State

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2743
Author(s):  
Tamara M. Díez-Rodríguez ◽  
Enrique Blázquez-Blázquez ◽  
Ernesto Pérez ◽  
María L. Cerrada
Keyword(s):  
Lactic Acid ◽  
Mesoporous Silica ◽  
Isothermal Crystallization ◽  
Physical Aging ◽  
Glassy State ◽  
Poly Lactic Acid ◽  
Molten State ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray

Several composites based on an L-rich poly(lactic acid) (PLA) with different contents of mesoporous Santa Barbara Amorphous (SBA-15) silica were prepared in order to evaluate the effect of the mesoporous silica on the resultant PLA materials by examining morphological aspects, changes in PLA phases and their transitions, and, primarily, the influence on some final properties. Melt extrusion was chosen for the obtainment of the composites, followed by quenching from the melt to prepare films. Completely amorphous samples were then attained, as deduced from X-ray diffraction and differential scanning calorimetry (DSC) analyses. Thermogravimetric analysis (TGA) results demonstrated that the presence of SBA-15 particles in the PLA matrix did not exert any significant influence on the thermal decomposition of these composites. An important nucleation effect of the silica was found in PLA, especially under isothermal crystallization either from the melt or from its glassy state. As expected, isothermal crystallization from the glass was considerably faster than from the molten state, and these high differences were also responsible for a more considerable nucleating role of SBA-15 when crystallizing from the melt. It is remarkable that the PLA under analysis showed very close temperatures for cold crystallization and its subsequent melting. Moreover, the type of developed polymorphs did not accomplish the common rules previously described in the literature. Thus, all the isothermal experiments led to exclusive formation of the α modification, and the observation of the α’ crystals required the annealing for long times at temperatures below 80 °C, as ascertained by both DSC and X-ray diffraction experiments. Finally, microhardness (MH) measurements indicated a competition between the PLA physical aging and the silica reinforcement effect in the as-processed amorphous films. Physical aging in the neat PLA was much more important than in the PLA matrix that constituted the composites. Accordingly, the MH trend with SBA-15 content was strongly dependent on aging times.

Isothermal Crystallization Behavior and Kinetics of Poly (lactic acid) Filled with a Novel Nucleating Agent

2014 ◽  
Vol 887-888 ◽  
pp. 716-722
Author(s):  
Nai Xu ◽  
Xing Hui Wang ◽  
Li Sha Pan ◽  
Su Juan Pang ◽  
Xuan Chen ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Isothermal Crystallization ◽  
Crystallization Behavior ◽  
Nucleating Agent ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry ◽  
Nucleation Effect ◽  
Amide Derivatives ◽  
Aromatic Amide ◽  
Kinetics Of

The crystallization behavior and crystalline structure of poly (lactic acid) (PLA) filled with a novel nucleating agent (TMC328), which is a kind of aromatic amide derivatives, were investigated using differential scanning calorimetry (DSC) and wide angle X-ray (XRD). In isothermal crystallization from the melt, the present of TMC328 remarkably affected the isothermal crystalline behaviors of PLA. PLA/0.5% TMC328 sample exhibited very short crystallization half-times at 90-130 °C. Furthermore, the Avrami theory was used to describe the isothermal crystallization kinetics of PLA/TMC328 samples. It is confirmed that TMC328 showed a significant heterogeneous nucleation effect on the crystallization of PLA matrix. Moreover, XRD measurement indicates that TMC328 is a kind of α-form nucleating agent for PLA.

DSC AND ELECTRICAL CONDUCTIVITY STUDIES ON SUPERIONIC ALL-GLASS PHOSPHATE-BASED COMPOSITES

2011 ◽  
Vol 04 (02) ◽  
pp. 139-142
Author(s):  
JAN L. NOWIŃSKI ◽  
WIOLETA ŚLUBOWSKA ◽  
JERZY E. GARBARCZYK ◽  
MAREK WASIUCIONEK
Keyword(s):  
Electrical Conductivity ◽  
Electrical Properties ◽  
Phosphate Glasses ◽  
Superionic Conductors ◽  
X Ray Diffraction ◽  
Glass Composite ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Dsc Studies

The work investigates electrical properties of all-glass composite Ag +-ion conductors based on silver phosphate glasses. A combination of X-ray diffraction (XRD) and differential scanning calorimetry (DSC) was used for characterization of the samples. The impedance spectroscopy (IS) was applied to determine the electrical conductivity in a wide temperature range (from -140 to +20°C). Results of the DSC studies indicate that all-glass materials prepared from the powdered glasses are bi-phasic. On the other hand their electrical properties resemble homogeneous rather than heterogeneous superionic conductors.

Blending and plasticising effects on the behaviour of poly(lactic acid)/poly(ε-caprolactone)

2018 ◽  
Vol 26 (5-6) ◽  
pp. 337-345 ◽  
Author(s):  
Nesrine Khitas ◽  
Kamira Aouachria ◽  
Mohamed Tahar Benaniba
Keyword(s):  
Thermal Stability ◽  
Lactic Acid ◽  
Nucleating Agent ◽  
Degree Of Crystallinity ◽  
Poly Lactic Acid ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Triethyl Citrate ◽  
Acetyl Tributyl Citrate ◽  
The Degree Of Crystallinity

Polymer blending is one of the most convenient methods to be used to overcome the limitations of some single properties of polymers and to achieve the combinations required for specific applications. Another feasible common practice is the incorporation of additives of low molecular weight such as plasticisers to impart flexibility, improve toughness and lower the glass transition temperature ( Tg). This study focused on the effects of blending and plasticising on the crystallisation behaviour of poly(lactic acid) (PLA)/poly(ε-caprolactone) (PCL). PCL with longer degradation time compared with other polymers was blended with PLA to overcome the limitation of its brittleness and poor thermal stability. Acetyl tributyl citrate (ATBC) and acetyl triethyl citrate (TEC) were used as plasticiser in PLA/PCL blends. The rigid and plasticised blends at various ratios were analysed by differential scanning calorimetry, thermogravimetric analysis and X-ray diffraction. The results revealed a slight increase in the degree of crystallinity and a significant increase in the Tg of PLA due to the addition of PCL. The addition of ATBC has promoted a decrease in thermal stability of the blends. The slight increase in the degree of crystallinity suggested that PCL acted as a nucleating agent. The citrate plasticisers were shown to lower the Tg and have much more enhanced the crystallisation of PLA. Moreover, the rigid and plasticised blends were shown to be partially miscible.

scholarly journals Biodegradable Poly(Lactic Acid)/Multiwalled Carbon Nanotube Nanocomposite Fabrication Using Casting And Hot Press Techniques

2015 ◽  
Vol 60 (2) ◽  
pp. 1557-1559 ◽  
Author(s):  
S.G. Park ◽  
A. Abdal-Hay ◽  
J.K. Lim
Keyword(s):  
Lactic Acid ◽  
Carbon Nanotube ◽  
Multiwalled Carbon Nanotube ◽  
Poly Lactic Acid ◽  
Hot Press ◽  
X Ray Diffraction ◽  
Multiwalled Carbon ◽  
X Ray ◽  
Biodegradable Poly ◽  
Composite Samples

Abstract Biodegradable advanced polymer composites have recently received a large amount of attention. The present study aimed to design poly(lactic acid) multiwalled carbon nanotube nanocomposites (PLA/MWCNTs) using a simple fabrication technique. A PLA sheet was first dissolved in dichloromethane, and MWCNTs were subsequently added at various concentrations (0.5, 1.5 and 5%) while applying shear strain stirring to achieve dispersion of carbon nanotubes (CNTs). These solutions were then molded and a hot press was used to generate sheets free of voids with entrapped solvent. The prepared samples were characterized using field emission scanning electron microscopy (FE-SEM), x-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA). Our data showed composite samples free of defects and voids, indicating that the hot press is capable of generating sufficiently compact polymer matrices. Additionally, TGA and FTIR showed significant bonding interactions between the PLA matrix and the nano-fillers. Collectively, our results suggest that incorporation of CNTs as nano-fillers into biodegradable polymers may have multiple applications in many different sectors.

Crystallization Behavior of Poly(lactic acid) Nucleated by a Hydrazide Compound

2013 ◽  
Vol 710 ◽  
pp. 85-88 ◽  
Author(s):  
Cheng Lang Li ◽  
Qiang Dou
Keyword(s):  
Differential Scanning Calorimetry ◽  
Lactic Acid ◽  
Crystallization Behavior ◽  
Polarized Light ◽  
Nucleating Agent ◽  
Poly Lactic Acid ◽  
Melt Blending ◽  
Scanning Calorimetry ◽  
Internal Mixer ◽  
Melting And Crystallization

A hydrazide compound (N-4) was used as a nucleating agent to induce the crystallization of poly (lactic acid) (PLA). PLA/N-4 samples were prepared by melt blending in an internal mixer. The melting and crystallization behavior and spherulitic morphology of the samples doped with different contents of N-4 were investigated by means of differential scanning calorimetry (DSC) and polarized light microscopy (PLM). It is found that the crystallization temperature and crystallinity increased but the spherulitic size of PLA decreased for the nucleated samples. It is indicated that N-4 is an effective nucleating agent for PLA.

Sign in / Sign up

Export Citation Format

Share Document