scholarly journals Strippable Polymeric Nanocomposites Comprising “Green” Chelates, for the Removal of Heavy Metals and Radionuclides

Polymers ◽  
2021 ◽  
Vol 13 (23) ◽  
pp. 4194
Author(s):  
Gabriela Toader ◽  
Daniela Pulpea ◽  
Traian Rotariu ◽  
Aurel Diacon ◽  
Edina Rusen ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Complexing Agents ◽  
Mechanical And Thermal Properties ◽  
Polymeric Nanocomposites ◽  
Retention Capacity ◽  
Metal Retention ◽  
Removal Of Heavy Metals ◽  
Iminodisuccinic Acid ◽  
Minimal Environmental Impact

The issue of heavy metal and radionuclide contamination is still causing a great deal of concern worldwide for environmental protection and industrial sites remediation. Various techniques have been developed for surface decontamination aiming for high decontamination factors (DF) and minimal environmental impact, but strippable polymeric nanocomposite coatings are some of the best candidates in this area. In this study, novel strippable coatings for heavy metal and radionuclides decontamination were developed based on the film-forming ability of polyvinyl alcohol, with the remarkable metal retention capacity of bentonite nanoclay, together with the chelating ability of sodium alginate and with “new-generation” “green” complexing agents: iminodisuccinic acid (IDS) and 2-phosphonobutane-1,2,4-tricarboxylic acid (PBTC). These environmentally friendly water-based decontamination solutions are capable of generating strippable polymeric films with optimized mechanical and thermal properties while exhibiting high decontamination efficiency (DF ≈ 95–98% for heavy metals tested on glass surface and DF ≈ 91–97% for radionuclides 241Am, 90Sr-Y and 137Cs on metal, painted metal, plastic, and glass surfaces).

Applications of Bentonite to Soil Decontamination

2018 ◽  
Vol 69 (7) ◽  
pp. 1695-1698
Author(s):  
Marin Rusanescu ◽  
Carmen Otilia Rusanescu ◽  
Gheorghe Voicu ◽  
Mihaela Begea
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Laboratory Experiments ◽  
Experimental Studies ◽  
Heavy Metal Concentration ◽  
Polluted Soil ◽  
Raw Material ◽  
Soil Decontamination ◽  
Metal Retention ◽  
Removal Of Heavy Metals

A calcium bentonite from Orasu Nou deposit (Satu Mare Romania) was used as raw material. We have conducted laboratory experiments to determine the influence of bentonite on the degree of heavy metal retention. It has been observed that the rate of retention increases as the heavy metal concentration decreases. Experimental studies have been carried out on metal retention ( Zn) in bentonite. In this paper, we realized laboratory experiments for determining the influence of metal (Zn) on the growth and development of two types of plants (Pelargonium domesticum and Kalanchoe) and the effect of bentonite on the absorption of pollutants. These flowers were planted in unpolluted soil, in heavy metal polluted soil and in heavy metal polluted soil to which bentonite was added to observe the positive effect of bentonite. It has been noticed that the flowers planted in unpolluted soil and polluted with heavy metals to which bentonite has been added, the flowers have flourished, the leaves are still green and the plants whose soils have been polluted with heavy metals began to dry after 6 days, three weeks have yellowish leaves and flowers have dried. Experiments have demonstrated the essential role of bentonite for the removal of heavy metals polluted soil.

scholarly journals Adsorption of heavy metal by natural clayey soil

2015 ◽  
Vol 3 (1) ◽  
Author(s):  
Wawan Budianta
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Soil Sample ◽  
Waste Disposal ◽  
Clayey Soil ◽  
Batch Experiment ◽  
Concentrated Solutions ◽  
Retention Capacity ◽  
Metal Retention ◽  
Soil Batch

This study focused on the capability of Clayey soil to retain and release heavy metals. Batch experiment for sample of clayey soil was conducted with several concentrated solutions of heavy metals. The results show that the clayey soil sample may have a relatively high heavy metal retention capacity. This is particularly positive in the context of municipal waste disposal (landfills) in Indonesia Keywords: Adsorption, heavy metal, clayey soil, batch experiment

scholarly journals Eco-Friendly β-cyclodextrin and Linecaps Polymers for the Removal of Heavy Metals

Polymers ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 1658 ◽  
Author(s):  
Rubin Pedrazzo ◽  
Smarra ◽  
Caldera ◽  
Musso ◽  
Dhakar ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Sea Water ◽  
Carboxyl Groups ◽  
Sodium Ions ◽  
Retention Capacity ◽  
Environment Friendly ◽  
Heavy Metal Cations ◽  
Removal Of Heavy Metals ◽  
Pea Starch

Environment-friendly nanosponges, having a high content of carboxyl groups, were synthesized by crosslinking β-cyclodextrin and linecaps, a highly soluble pea starch derivative, with citric acid in water. Additionally, pyromellitic nanosponges were prepared by reacting β-cyclodextrin and linecaps with pyromellitic dianhydride in dimethyl sulfoxide and used in comparison with the citric nanosponges. After ion-exchange of the carboxyl groups H+ with sodium ions, the ability of the nanosponges to sequester heavy metal cations was investigated. At a metal concentration of 500 ppm, the pyromellitate nanosponges exhibited a higher retention capacity than the citrate nanosponges. At lower metal concentrations (≤50 ppm) both the citrate and the pyromellitate nanosponges showed high retention capacities (up to 94% of the total amount of metal), while, in the presence of interfering sea water salts, the citrate nanosponges were able to selectively adsorb a significantly higher amount of heavy metals than the pyromellitate nanosponges, almost double in the case of Cu2+.

scholarly journals A systematic study for removal of heavy metals from aqueous media using Sorghum bicolor: an efficient biosorbent

2018 ◽  
Vol 77 (10) ◽  
pp. 2355-2368 ◽  
Author(s):  
Khalida Naseem ◽  
Zahoor H. Farooqi ◽  
Muhammad Z. Ur Rehman ◽  
Muhammad A. Ur Rehman ◽  
Robina Begum ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Metal Ions ◽  
Heavy Metal Ions ◽  
Aqueous Media ◽  
Review Article ◽  
Isotherm Models ◽  
Adsorption Efficiency ◽  
Adsorption Isotherm Models ◽  
Removal Of Heavy Metals

Abstract This review is based on the adsorption characteristics of sorghum (Sorghum bicolor) for removal of heavy metals from aqueous media. Different parameters like pH, temperature of the medium, sorghum concentration, sorghum particle size, contact time, stirring speed and heavy metal concentration control the adsorption efficiency of sorghum biomass for heavy metal ions. Sorghum biomass showed maximum efficiency for removal of heavy metal ions in the pH range of 5 to 6. It is an agricultural waste and is regarded as the cheapest biosorbent, having high adsorption capacity for heavy metals as compared to other reported adsorbents, for the treatment of heavy metal polluted wastewater. Adsorption of heavy metal ions onto sorghum biomass follows pseudo second order kinetics. Best fitted adsorption isotherm models for removal of heavy metal ions on sorghum biomass are Langmuir and Freundlich adsorption isotherm models. Thermodynamic aspects of heavy metal ions adsorption onto sorghum biomass have also been elaborated in this review article. How adsorption efficiency of sorghum biomass can be improved by different physical and chemical treatments in future has also been elaborated. This review article will be highly useful for researchers working in the field of water treatment via biosorption processing. The quantitative demonstrated efficiency of sorghum biomass for various heavy metal ions has also been highlighted in different sections of this review article.

scholarly journals Treatment of Poultry Wastewater Using Shells from African Cherry Seeds, Egg and Crab

2020 ◽  
pp. 16-30
Author(s):  
Abimbola O. Aleshinloye ◽  
Kemayou Ngangsso ◽  
Feyisara B. Adaramola ◽  
Adebayo Onigbinde
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Microwave Plasma ◽  
Low Cost ◽  
Chloride Content ◽  
Agricultural Wastes ◽  
Wastewater Sample ◽  
Animal Source ◽  
Removal Of Heavy Metals ◽  
Poultry Wastewater

This study investigated the potential of some agricultural wastes viz; African Star apple seed shell (ASS, plant source), crab shell (CS, animal source) and chicken egg shell (ES, animal source) as eco-friendly and low-cost biological materials for the removal of heavy metals from poultry wastewater. TS, TSS and TDS of the wastewater sample were assayed by filtration methods, chloride content by previously reported method and heavy metal contents (Zn, V, Cd, Fe, Ni, Cu, Co, Pb, Cr and Mn); were analyzed using Microwave Plasma Atomic Emission Spectrometer. The results of the solids and chloride contents of the poultry wastewater were TDS (3100 mg/L), TS (3700 mg/L), TSS (6000 mg/L) and chloride (4.7 g/L); all above the EPA permissible limits. Results of the FTIR analysis showed that ASS is an amide polymer while the CS and ES shells are mixtures of amide and carbonate polymers. Also, results of heavy metal analysis before and after adsorption showed that ASS caused removal of Zn, V, Fe, Cu, Co/ Pb and Mn by 48.27, 32.22, 49.64, 91.44, 100 and 82.39% respectively while Cd, Ni and Cr contents increased by 31, 61 and 48.3% respectively. CS showed removal of Fe, Ni/ Co/ Cr, Pb and Mn by 89.64, 100, 3.51 and 95.96% respectively while Zn, V, Cd and Cu contents increased by 1.7, 61.2, 76.1 and 68.1% respectively. Meanwhile, with ES, the contents of Zn, Fe, Ni, Cu, Cr and Mn increased by 31.56, 86.36, 100, 55.5, 45.80 and 90.33% respectively while the contents of V, Cd, Co and Pb decreased by 78.9, 86.7, 42.5 and 46.2% respectively. This study demonstrated the use of ASS, CS and ES as low- cost and eco-friendly agricultural wastes with significant potential for removal of heavy metals from wastewaters.

Heavy metal removal from wastewater and leachate co-treatment sludge by sulfur oxidizing bacteria

2001 ◽  
Vol 44 (10) ◽  
pp. 53-58 ◽  
Author(s):  
L. C. Aralp ◽  
A. Erdincler ◽  
T. T. Onay
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Municipal Wastewater ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Heavy Metal Concentration ◽  
Organic Content ◽  
Removal Of Heavy Metals ◽  
Sulfur Oxidizing ◽  
Sulfur Oxidizing Bacteria

Heavy metal concentration in sludge is one of the major obstacles for the application of sludge on land. There are various methods for the removal of heavy metals in sludge. Using sulfur oxidizing bacteria for microbiological removal of heavy metals from sludges is an outstanding option because of high metal solubilization rates and the low cost. In this study, bioleaching by indigenous sulfur oxidizing bacteria was applied to sludges generated from the co-treatment of municipal wastewater and leachate for the removal of selected heavy metals. Sulfur oxidizing bacteria were acclimated to activated sludge. The effect of the high organic content of leachate on the bioleaching process was investigated in four sets of sludges having different concentrations of leachate. Sludges in Sets A, B, C and D were obtained from co-treatment of wastewater and 3%, 5%, 7% and 10% (v/v) leachate respectively. The highest Cr, Ni and Fe solubilization was obtained from Set A. Sulfur oxidizing bacteria were totally inhibited in Set D that received the highest volume of leachate.

scholarly journals Bioremoval of Different Heavy Metals by the Resistant Fungal StrainAspergillus niger

2018 ◽  
Vol 2018 ◽  
pp. 1-7 ◽  
Author(s):  
Ismael Acosta-Rodríguez ◽  
Juan F. Cárdenas-González ◽  
Adriana S. Rodríguez Pérez ◽  
Juana Tovar Oviedo ◽  
Víctor M. Martínez-Juárez
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Aspergillus Niger ◽  
Fungal Biomass ◽  
Dry Weight ◽  
Removal Capacity ◽  
Removal Of Heavy Metals ◽  
The Ideal

The objective of this work was to study the resistance and removal capacity of heavy metals by the fungusAspergillus niger. We analyzed the resistance to some heavy metals by dry weight and plate: the fungus grew in 2000 ppm of zinc, lead, and mercury, 1200 and 1000 ppm of arsenic (III) and (VI), 800 ppm of fluor and cobalt, and least in cadmium (400 ppm). With respect to their potential of removal of heavy metals, this removal was achieved for zinc (100%), mercury (83.2%), fluor (83%), cobalt (71.4%), fairly silver (48%), and copper (37%). The ideal conditions for the removal of 100 mg/L of the heavy metals were 28°C, pH between 4.0 and 5.5, 100 ppm of heavy metal, and 1 g of fungal biomass.

Heavy Metal Removal in the Presence of Colloid-Stabilizing Organic Material and Complexing Agents

1986 ◽  
Vol 18 (1) ◽  
pp. 19-29 ◽  
Author(s):  
I. Licskó ◽  
I. Takács
Keyword(s):  
Heavy Metals ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Colloidal Dispersion ◽  
Laboratory Model ◽  
Complexing Agents ◽  
Stabilizing Agents ◽  
Removal Of Heavy Metals ◽  
Alkaline Conditions ◽  
The Stability

It has been established in laboratory model experiments that the removal of dissolved heavyimetals from wastewaters is rendered more difficult in the presence of colloid-stabilizing agents. This unfavourable effect can be eliminated by the addition of Mg2+ ions and the adjustment to a fairly high pH. By increasing the concentration of Mg2+ ions, the pH necessary for destroying the stability of colloidal dispersion can be lowered. These findings also apply to the combined removal of different heavy metals (Cu, Zn, Cr(III), Ni, Cd). In alkaline conditions, in the presence of ammonium salts, some heavy metals (Cu, Zn, Ni) form high stability amine complexes. A higher pH is necessary for the breakdown of these complexes and the satisfactory removal of heavy metals.

scholarly journals Heavy metal removal from wastewater using various adsorbents: a review

2016 ◽  
Vol 7 (4) ◽  
pp. 387-419 ◽  
Author(s):  
Renu ◽  
Madhu Agarwal ◽  
K. Singh
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Aquatic Ecosystems ◽  
Adsorption Process ◽  
Metal Removal ◽  
Low Cost ◽  
Heavy Metal Removal ◽  
Review Article ◽  
Removal Capacity ◽  
Removal Of Heavy Metals

Heavy metals are discharged into water from various industries. They can be toxic or carcinogenic in nature and can cause severe problems for humans and aquatic ecosystems. Thus, the removal of heavy metals from wastewater is a serious problem. The adsorption process is widely used for the removal of heavy metals from wastewater because of its low cost, availability and eco-friendly nature. Both commercial adsorbents and bioadsorbents are used for the removal of heavy metals from wastewater, with high removal capacity. This review article aims to compile scattered information on the different adsorbents that are used for heavy metal removal and to provide information on the commercially available and natural bioadsorbents used for removal of chromium, cadmium and copper, in particular.

Impact of solution variables on the removal of heavy metals from wastewaters by a recycled iron sorbent

2000 ◽  
Vol 42 (1-2) ◽  
pp. 347-352
Author(s):  
E.H. Smith ◽  
S. Chatterjee
Keyword(s):  
Heavy Metals ◽  
Oxalic Acid ◽  
Metal Speciation ◽  
Surface Finishing ◽  
Complexing Agents ◽  
Lead Removal ◽  
Adsorption Equilibria ◽  
Removal Of Heavy Metals ◽  
Cadmium And Lead ◽  
The Impact

Waste shot-blast fines from surface finishing processes have been demonstrated to be effective for removing heavy metals from solution by adsorption.The technology offers the potential for inexpensive recovery and reuse of a material normally discarded as a solid waste. While metal removals compare favorably with those achieved by commercial sorbents, applications issues such as the impact of background metal-complexing agents require investigation. The presence of oxalic acid, a complexing organic compound, impacted cadmium and lead adsorption in accordance with predictions from metal speciation equilibria; i.e., a small but measurable reduction in lead removal was observed, but cadmium adsorption was relatively unaffected. The effects were repeated in dynamic column experiments, with lead removals reduced by 15 to 20% in the presence of the ligand. Efforts to model adsorption equilibria in the presence of oxalic acid did not fully capture the reduced lead removal, presumably because the model does not consider the complete formation of metal-oxalic acid complexes prior to contact with the sorbent.

Sign in / Sign up

Export Citation Format

Share Document