scholarly journals Investigation of Impacts on Printed Circuit Board Laminated Composites Caused by Surface Finish Application

Polymers ◽  
2021 ◽  
Vol 13 (19) ◽  
pp. 3203
Author(s):  
Denis Froš ◽  
Karel Dušek ◽  
Petr Veselý
Keyword(s):  
Bond Strength ◽  
Thermal Shock ◽  
Surface Finish ◽  
Printed Circuit Board ◽  
Thermomechanical Properties ◽  
Circuit Board ◽  
Printed Circuit ◽  
Surface Finishes ◽  
The Impact ◽  
Selection Of

The purpose of this study was to compare the strength of the bond between resin and glass cloth for various composites (laminates) and its dependence on utilized soldering pad surface finishes. Moreover, the impact of surface finish application on the thermomechanical properties of the composites was evaluated. Three different laminates with various thermal endurances were included in the study. Soldering pads were covered with OSP and HASL surface finishes. The strength of the cohesion of the resin upper layer was examined utilizing a newly established method designed for pulling tests. Experiments studying the bond strength were performed at a selection of laminate temperatures. Changes in thermomechanical behavior were observed by thermomechanical and dynamic mechanical analyses. The results confirmed the influence of the type of laminate and used surface finish on bond strength. In particular, permanent polymer degradation caused by thermal shock during HASL application was observed in the least thermally resistant laminate. A response to thermal shock was detected in thermomechanical properties of other laminates as well, but it does not seem to be permanent.

A Comparison of Immersion Gold and Tin Surface Finishes on Sensing Electrodes for PCB Environmental Saltwater Concentration Sensors

2016 ◽  
Vol 2016 (1) ◽  
pp. 000557-000562
Author(s):  
Robert N. Dean ◽  
Frank T. Werner ◽  
Michael J. Bozack
Keyword(s):  
Surface Finish ◽  
Printed Circuit Board ◽  
Chemical Constituents ◽  
Low Cost ◽  
Circuit Board ◽  
Testing Environment ◽  
Printed Circuit ◽  
Sensor Performance ◽  
Sensing Applications ◽  
Surface Finishes

Abstract Printed circuit board (PCB) sensors using low-cost commercial printed circuit board fabrication processes have been demonstrated for environmental sensing applications. One configuration of these sensors uses exposed electrodes to measure saltwater concentration in freshwater/seawater mixtures, through monitoring the resistance between the electrodes when they are immersed in the saltwater/freshwater solution. The lowest cost commercial PCB processes use an immersion Sn HASL surface finish on exposed copper cladding, including the sensing electrodes. This commercial PCB process has been demonstrated to make an effective, low-cost, short-lifetime sensor for saltwater concentration testing. The Sn finish, however, may not be optimal for this application. Sn oxidizes, which can interfere with sensor performance. Additionally, Sn and Sn oxides are potentially reactive with chemical constituents in seawater and seawater/freshwater solutions. An immersion Au (ENIG) surface finish is certainly less reactive with the atmosphere and chemicals likely present in the testing environment. However, an immersion Au finish increases the cost of the sensors by 30% to 40%. To investigate if the possible benefits of the more expensive Au surface finish are worth the extra expense, a study was performed where identical PCB sensors were procured from a commercial vendor with their standard low-cost Sn HASL finish and with their standard ENIG surface finish. Both sets of sensors were then evaluated in concentrations of seawater and freshwater, from 0% to 100% seawater concentration, using freshwater samples from a natural freshwater source near the coast where the seawater was obtained. Testing demonstrated an insignificant difference in sensor performance between the Sn HASL and the ENIG coated sensing electrodes. The results of this investigation indicated that for applications where the sensors will not be used for long periods of time, the added expense of an immersion Au surface finish is not worth the added cost.

Numerical Simulation and Experimental Measurement of a Printed Circuit Board Subjected to Drop Test

2009 ◽  
Vol 419-420 ◽  
pp. 37-40
Author(s):  
Shiuh Chuan Her ◽  
Shien Chin Lan ◽  
Chun Yen Liu ◽  
Bo Ren Yao
Keyword(s):  
Finite Element ◽  
Experimental Measurement ◽  
Test Specimen ◽  
Printed Circuit Board ◽  
Drop Impact ◽  
Simulation Technique ◽  
Drop Test ◽  
Circuit Board ◽  
Printed Circuit ◽  
The Impact

Drop test is one of the common methods for determining the reliability of electronic products under actual transportation conditions. The aim of this study is to develop a reliable drop impact simulation technique. The test specimen of a printed circuit board is clamped at two edges on a test fixture and mounted on the drop test machine platform. The drop table is raised at the height of 50mm and dropped with free fall to impinge four half-spheres of Teflon. One accelerometer is mounted on the center of the specimen to measure the impact pulse. The commercial finite element software ANSYS/LS-DYNA is applied to compute the impact acceleration and dynamic strain on the test specimen during the drop impact. The finite element results are compared to the experimental measurement of acceleration with good correlation between simulation and drop testing. With the accurate simulation technique, one is capable of predicting the impact response and characterizing the failure mode prior to real reliability test.

Research on Liberation Mechanism of the Impact Crushing Waste Printed Circuit Board

2010 ◽  
Vol 113-116 ◽  
pp. 730-734 ◽  
Author(s):  
Chen Long Duan ◽  
Yue Min Zhao ◽  
Jing Feng He ◽  
Nian Xin Zhou
Keyword(s):  
Printed Circuit Boards ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Distribution Model ◽  
Evaluation Indexes ◽  
Printed Circuit ◽  
Waste Printed Circuit Boards ◽  
Waste Printed Circuit Board ◽  
Impact Crushing ◽  
The Impact

The reutilization of waste Printed Circuit Boards (PCB) is a focused topic in the field of environment protection and resource recycling, and the crushing is the crucial process for recycling waste PCB. A hamper impacting crusher was used to achieve metals crushing liberation from non-metals, the liberation mechanism of PCB can be explained by dispersion liberation accompanied disengaging liberation. The Rosin-Rammler distribution model of crushed PCB particle was put forward. The evaluation indexes show that Rosin-Rammler function can accurately describe size distribution of PCB particles because the convergence property R2 is 0.99694 and fitting error E is 4.80658. The selective crushing is appearance with metals concentrated in coarser fraction and non-metals in finer size during comminution processing. The impact crushing is an effective method to metals liberation of PCB particles.

Failure Analysis of Halogen-Free Printed Circuit Board Assembly Under Board-Level Drop Test

2012 ◽  
Vol 134 (1) ◽  
Author(s):  
Hung-Jen Chang ◽  
Chau-Jie Zhan ◽  
Tao-Chih Chang ◽  
Jung-Hua Chou
Keyword(s):  
Printed Circuit Board ◽  
Drop Test ◽  
Circuit Board ◽  
Printed Circuit Board Assembly ◽  
Printed Circuit ◽  
Plastic Ball ◽  
Circuit Board Assembly ◽  
Halogen Free ◽  
Board Level ◽  
The Impact

In this study, a lead-free dummy plastic ball grid array component with daisy-chains and Sn4.0Ag0.5Cu Pb-free solder balls was assembled on an halogen-free high density interconnection printed circuit board (PCB) by using Sn1.0Ag0.5Cu solder paste on the Cu pad surfaces of either organic solderable preservative (OSP) or electroless nickel immersion gold (ENIG). The assembly was tested for the effect of the formation extent of Ag3Sn intermetallic compound. Afterward a board-level pulse-controlled drop test was conducted on the as-reflowed assemblies according to the JESD22-B110 and JESD22-B111 standards, the impact performance of various surface finished halogen-free printed circuit board assembly was evaluated. The test results showed that most of the fractures occurred around the pad on the test board first. Then cracks propagated across the outer build-up layer. Finally, the inner copper trace was fractured due to the propagated cracks, resulting in the failure of the PCB side. Interfacial stresses numerically obtained by the transient stress responses supported the test observation as the simulated initial crack position was the same as that observed.

Nonlinear Response of a Printed Circuit Board in Shock

2009 ◽  
Author(s):  
M. Vujosevic ◽  
P. Raghavan ◽  
G. Ramanathan ◽  
W. Hezeltine ◽  
K. Blue
Keyword(s):  
Printed Circuit Board ◽  
Transfer Functions ◽  
Numerical Approach ◽  
Circuit Board ◽  
Special Importance ◽  
Strain Measurements ◽  
Printed Circuit ◽  
Numerical Finite Element ◽  
Nonlinear Deformations ◽  
The Impact

This work focuses on deformation mechanisms taking place in a Printed Circuit Board (PCB) exposed to high impact shock. A combined experimental, theoretical, and numerical approach has been applied to address both the nature of the observed deformation and its modeling and test metrology implications. Experimental evidence overwhelmingly indicates that a PCB in both test and system applications undergoes nonlinear deformations. Geometric nonlinearity of board response is attributed to the elevated in-plane (membrane) stresses that develop when a drop height and/or inertia forces are significant. The impact of these stresses on deformations (board strain) was quantified using a specially designed test. Membrane stresses were also accounted for in a numerical (Finite Element Method) model developed and carefully validated in the course of this study. The model shows a very good agreement with test data. The nonlinearity of PCB deformation in shock, i.e. the fact that both bending moments and in-plane forces are present in the board has important implications on test metrology development and on correlation between the measured board strain and stresses in interconnects of surface mounted components. Of special importance is the impact that nonlinearity can have on development of transfer functions between strain measurements on system boards and strain measurements on test boards, which is also addressed in the paper.

Sign in / Sign up

Export Citation Format

Share Document