scholarly journals Extruded-Calendered Sheets of Fully Recycled PP/Opaque PET Blends: Mechanical and Fracture Behaviour

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2360
Author(s):  
David Loaeza ◽  
Jonathan Cailloux ◽  
Orlando Santana Pérez ◽  
Miguel Sánchez-Soto ◽  
Maria Lluïsa Maspoch
Keyword(s):  
Fracture Behaviour ◽  
Raw Materials ◽  
Tensile Tests ◽  
Recycling Rate ◽  
Recycled Plastics ◽  
Microfibrillar Composites ◽  
Microfibrillar Structure ◽  
Work Of Fracture ◽  
O Phase

This work presents the experimental results of the mechanical and fracture behaviour of three polymeric blends prepared from two recycled plastics, namely polypropylene and opaque poly (ethylene terephthalate), where the second one acted as a reinforcement phase. The raw materials were two commercial degrees of recycled post-consumer waste, i.e., rPP and rPET-O. Sheets were manufactured by a semi-industrial extrusion-calendering process. The mechanical and fracture behaviours of manufactured sheets were analyzed via tensile tests and the essential work of fracture approach. SEM micrographics of cryofractured sheets revelated the development of in situ rPP/rPET-O microfibrillar composites when 30 wt.% of rPET-O was added. It was observed that the yield stress was not affected with the addition of rPET-O. However, the microfibrillar structure increased the Young’s modulus by more than a third compared with rPP, fulfilling the longitudinal value predicted by the additive rule of mixtures. Regarding the EWF analysis, the resistance to crack initiation was highly influenced by the resistance to its propagation owing to morphology-related instabilities during tearing. To analyze the initiation stage, a partition energy method was successfully applied by splitting the total work of fracture into two specific energetic contributions, namely initiation and propagation. The results revelated that the specific essential initiation-related work of fracture was mainly affected by rPET-O phase. Remarkably, its value was significantly improved by a factor of three with the microfibrillar structure of rPET-O phase. The results allowed the exploration of the potential ability of manufacturing in situ MFCs without a “precursor” morphology, providing an economical way to promote the recycling rate of PET-O, as this material is being discarded from current recycling processes.

scholarly journals Facile Preparation of Mesoporous MCM-48 Containing Silver Nanoparticles with Fly Ash as Raw Materials for CO Catalytic Oxidation

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 841
Author(s):  
Dong Tian ◽  
Yonghong Chen ◽  
Xiaoyong Lu ◽  
Yihan Ling ◽  
Bin Lin
Keyword(s):  
Silver Nanoparticles ◽  
Fly Ash ◽  
Co Oxidation ◽  
Surface Composition ◽  
Raw Materials ◽  
Silica Source ◽  
Co Conversion ◽  
Co Catalytic Oxidation ◽  
Adsorption Desorption

An environmentally friendly method was proposed to prepare mesoporous Mobil Composition of Matter No.48 (MCM-48) using fly ash as the silica source. Silver nanoparticles were infiltrated on MCM-48 facilely by an in situ post-reduction method and evaluated as an effective catalyst for CO oxidation. The as-prepared MCM-48 and Ag/MCM-48 nanoparticles were characterized by XRD, N2 adsorption/desorption, and TEM. Investigations by means of XPS for Ag/MCM-48 were performed in order to illuminate the surface composition of the samples. Studies revealed the strong influence of the loading of Ag nanoparticles on catalysts in the oxidation of CO. CO conversion values for Ag/MCM-48 of 10% and 100% were achieved at temperatures of 220 °C and 270 °C, respectively, indicating that the Ag-decorated MCM-48 catalyst is extremely active for CO oxidation.

scholarly journals Fe3O4@C Nanoparticles Synthesized by In Situ Solid-Phase Method for Removal of Methylene Blue

Nanomaterials ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 330
Author(s):  
Hengli Xiang ◽  
Genkuan Ren ◽  
Yanjun Zhong ◽  
Dehua Xu ◽  
Zhiye Zhang ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Solid Phase ◽  
Raw Materials ◽  
Phase Method ◽  
Maximum Adsorption Capacity ◽  
High Catalytic Activity ◽  
Solid Phase Reaction ◽  
Phase Reaction ◽  
High Concentrations

Fe3O4@C nanoparticles were prepared by an in situ, solid-phase reaction, without any precursor, using FeSO4, FeS2, and PVP K30 as raw materials. The nanoparticles were utilized to decolorize high concentrations methylene blue (MB). The results indicated that the maximum adsorption capacity of the Fe3O4@C nanoparticles was 18.52 mg/g, and that the adsorption process was exothermic. Additionally, by employing H2O2 as the initiator of a Fenton-like reaction, the removal efficiency of 100 mg/L MB reached ~99% with Fe3O4@C nanoparticles, while that of MB was only ~34% using pure Fe3O4 nanoparticles. The mechanism of H2O2 activated on the Fe3O4@C nanoparticles and the possible degradation pathways of MB are discussed. The Fe3O4@C nanoparticles retained high catalytic activity after five usage cycles. This work describes a facile method for producing Fe3O4@C nanoparticles with excellent catalytic reactivity, and therefore, represents a promising approach for the industrial production of Fe3O4@C nanoparticles for the treatment of high concentrations of dyes in wastewater.

scholarly journals Effect of Sintering Temperature on Microstructure and Mechanical Properties of Hot-Pressed Fe/FeAl2O4 Composite

Crystals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 422
Author(s):  
Kuai Zhang ◽  
Yungang Li ◽  
Hongyan Yan ◽  
Chuang Wang ◽  
Hui Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Bending Strength ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Hot Press ◽  
Microstructure And Mechanical Properties ◽  
Powder Particles ◽  
Hot Press Sintering ◽  
Sintering Method

An Fe/FeAl2O4 composite was prepared with Fe-Fe2O3-Al2O3 powder by a hot press sintering method. The mass ratio was 6:1:2, sintering pressure was 30 MPa, and holding time was 120 min. The raw materials for the powder particles were respectively 1 µm (Fe), 0.5 µm (Fe2O3), and 1 µm (Al2O3) in diameter. The effect of sintering temperature on the microstructure and mechanical properties of Fe/FeAl2O4 composite was studied. The results showed that Fe/FeAl2O4 composite was formed by in situ reaction at 1300 °C–1500 °C. With the increased sintering temperature, the microstructure and mechanical properties of the Fe/FeAl2O4 composite showed a change law that initially became better and then became worse. The best microstructure and optimal mechanical properties were obtained at 1400 °C. At this temperature, the grain size of Fe and FeAl2O4 phases in Fe/FeAl2O4 composite was uniform, the relative density was 96.7%, and the Vickers hardness and bending strength were 1.88 GPa and 280.0 MPa, respectively. The wettability between Fe and FeAl2O4 was enhanced with increased sintering temperature. And then the densification process was accelerated. Finally, the microstructure and mechanical properties of the Fe/FeAl2O4 composite were improved.

In Situ Preparation and Mechanical Properties of (ZrB2+ZrC)/Zr3[Al(Si)]4C6 Composites

2014 ◽  
Vol 602-603 ◽  
pp. 438-442
Author(s):  
Lei Yu ◽  
Jian Yang ◽  
Tai Qiu
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Bending Strength ◽  
Coefficient Of Thermal Expansion ◽  
Raw Materials ◽  
Linear Increase ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Uniform Microstructure

Fully dense (ZrB2+ZrC)/Zr3[Al (Si)]4C6 composites with ZrB2 content varying from 0 to 15 vol.% and fixed ZrC content of 10 vol.% were successfully prepared by in situ hot-pressing in Ar atmosphere using ZrH2, Al, Si, C and B4C as raw materials. With the increase of ZrB2 content, both the bending strength and fracture toughness of the composites increase and then decrease. The synergistic action of ZrB2 and ZrC as reinforcements shows significant strengthening and toughing effect to the Zr3[Al (Si)]4C6 matrix. The composite with 10 vol.% ZrB2 shows the optimal mechanical properties: 516 MPa for bending strength and 6.52 MPa·m1/2 for fracture toughness. With the increase of ZrB2 content, the Vickers hardness of the composites shows a near-linear increase from 15.3 GPa to 16.7 GPa. The strengthening and toughening effect can be ascribed to the unique mechanical properties of ZrB2 and ZrC reinforcements, the differences in coefficient of thermal expansion and modulus between them and Zr3[Al (Si)]4C6 matrix, fine grain strengthening and uniform microstructure derived by the in situ synthesis reaction.

Effect of self-assembling WC film upon diamond on adhesion strength with Fe-Co-Ni binder: In situ TEM tensile tests

2022 ◽  
Vol 208 ◽  
pp. 114331
Author(s):  
P.A. Loginov ◽  
A.A. Zaitsev ◽  
D.A. Sidorenko ◽  
E.A. Levashov
Keyword(s):  
Adhesion Strength ◽  
Tensile Tests ◽  
In Situ Tem ◽  
Self Assembling

Development of green nanocomposites reinforced by cellulose nanofibers extracted from paper sludge

2015 ◽  
Vol 29 (06n07) ◽  
pp. 1540025 ◽  
Author(s):  
Hitoshi Takagi ◽  
Antonio N. Nakagaito ◽  
Kazuya Kusaka ◽  
Yuya Muneta
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Mechanical Treatment ◽  
Raw Materials ◽  
Cellulose Nanofibers ◽  
Tensile Tests ◽  
Cellulose Nanofiber ◽  
Paper Sludge ◽  
Reinforcing Effect ◽  
Mechanical And Physical Properties

Cellulose nanofibers have been showing much greater potential to enhance the mechanical and physical properties of polymer-based composite materials. The purpose of this study is to extract the cellulose nanofibers from waste bio-resources; such as waste newspaper and paper sludge. The cellulosic raw materials were treated chemically and physically in order to extract individualized cellulose nanofiber. The combination of acid hydrolysis and following mechanical treatment resulted in the extraction of cellulose nanofibers having diameter of about 40 nm. In order to examine the reinforcing effect of the extracted cellulose nanofibers, fully biodegradable green nanocomposites were fabricated by composing polyvinyl alcohol (PVA) resin with the extracted cellulose nanofibers, and then the tensile tests were conducted. The results showed that the enhancement in mechanical properties was successfully obtained in the cellulose nanofiber/PVA green nanocomposites.

scholarly journals 2P1-C22 In situ Tensile Tests Using Silicon Microchip by TEM Nanomanipulator

2008 ◽  
Vol 2008 (0) ◽  
pp. _2P1-C22_1-_2P1-C22_2
Author(s):  
Masahiro NAKAJIMA ◽  
Taeko ANDO ◽  
Hidekazu ISHIHARA ◽  
Shigeki NAKAO ◽  
Shigeo ARAI ◽  
...  
Keyword(s):  
Tensile Tests ◽  
Silicon Microchip

scholarly journals Live-Scale Testing of Granular Materials Stabilized with Alkali-Activated Waste Glass and Carbide Lime

2021 ◽  
Vol 11 (23) ◽  
pp. 11286
Author(s):  
Marina Paula Secco ◽  
Débora Thaís Mesavilla ◽  
Márcio Felipe Floss ◽  
Nilo Cesar Consoli ◽  
Tiago Miranda ◽  
...  
Keyword(s):  
Portland Cement ◽  
Mechanical Performance ◽  
Raw Materials ◽  
Sodium Hydroxide Solution ◽  
Fine Sand ◽  
Field Application ◽  
Natural Soil ◽  
In Situ Tests ◽  
Alkali Activated

The increasingly strong search for alternative materials to Portland cement has resulted in the development of alkali-activated cements (AAC) that are very effective at using industrial by-products as raw materials, which also contributes to the volume reduction in landfilled waste. Several studies targeting the development of AAC—based on wastes containing silicon and calcium—for chemical stabilization of soils have demonstrated their excellent performance in terms of durability and mechanical performance. However, most of these studies are confined to a laboratory characterization, ignoring the influence and viability of the in situ construction process and, also important, of the in situ curing conditions. The present work investigated the field application of an AAC based on carbide lime and glass wastes to stabilize fine sand acting as a superficial foundation. The assessment was supported on the unconfined compressive strength (UCS) and initial shear modulus (G0) of the developed material, and the field results were compared with those prepared in the laboratory, up to 120 days curing. In situ tests were also developed on the field layers (with diameters of 450 and 900 mm and thickness of 300 mm) after different curing times. To establish a reference, the mentioned precursors were either activated with a sodium hydroxide solution or hydrated with water (given the reactivity of the lime). The results showed that the AAC-based mixtures developed greater strength and stiffness at a faster rate than the water-based mixtures. Specimens cured under controlled laboratory conditions showed better results than the samples collected in the field. The inclusion of the stabilized layers clearly increased the load-bearing capacity of the natural soil, while the different diameters produced different failure mechanisms, similar to those found in Portland cement stabilization.

Sign in / Sign up

Export Citation Format

Share Document