scholarly journals Sulfonated Polysulfone/TiO2(B) Nanowires Composite Membranes as Polymer Electrolytes in Fuel Cells

Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 2030
Author(s):  
Maria Jose Martinez-Morlanes ◽  
Carmen de la Torre-Gamarra ◽  
María Teresa Pérez-Prior ◽  
Sara Lara-Benito ◽  
Carmen del Rio ◽  
...  
Keyword(s):  
Fuel Cells ◽  
Composite Membranes ◽  
Proton Exchange ◽  
Maximum Temperature ◽  
X Ray Diffraction ◽  
Promising Candidate ◽  
Experimental Conditions ◽  
X Ray ◽  
Sulfonated Polysulfone ◽  
Conducting Membranes

New proton conducting membranes based on sulfonated polysulfone (sPSU) reinforced with TiO2(B) nanowires (1, 2, 5 and 10 wt.%) were synthesized and characterized. TiO2(B) nanowires were synthesized by means of a hydrothermal method by mixing TiO2 precursor in aqueous solution of NaOH as solvent. The presence of the TiO2(B) nanowires into the polymer were confirmed by means of Field Emission Scanning Electron Microscopy, Fourier transform infrared and X-ray diffraction. The thermal study showed an increase of almost 20 °C in the maximum temperature of sPSU backbone decomposition due to the presence of 10 wt.% TiO2(B) nanowires. Water uptake also is improved with the presence of hydrophilic TiO2(B) nanowires. Proton conductivity of sPSU with 10 wt.% TiO2(B) nanowires was 21 mS cm−1 (at 85 °C and 100% RH). Under these experimental conditions the power density was 350 mW cm−2 similar to the value obtained for Nafion 117. Considering all these obtained results, the composite membrane doped with 10 wt.% TiO2(B) nanowires is a promising candidate as proton exchange electrolyte in fuel cells (PEMFCs), especially those operating at high temperatures.

scholarly journals Synthesis and Characterization of Novel Green Hybrid Nanocomposites for Application as Proton Exchange Membranes in Direct Borohydride Fuel Cells

Energies ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1180 ◽  
Author(s):  
Marwa H. Gouda ◽  
Noha A. Elessawy ◽  
Diogo M.F. Santos
Keyword(s):  
Electron Microscopy ◽  
Fuel Cells ◽  
Low Cost ◽  
Composite Membranes ◽  
Proton Exchange ◽  
Hybrid Nanocomposites ◽  
Poly Vinyl Alcohol ◽  
Nanocomposite Membranes ◽  
X Ray ◽  
Direct Borohydride Fuel Cells

Organic–inorganic nanocomposite membranes for potential application in direct borohydride fuel cells (DBFCs) are formulated from sulfonated poly(vinyl alcohol) (SPVA) with the incorporation of (PO4-TiO2) and (SO4-TiO2) nanotubes as doping agents. The functionalization of PVA to SPVA was done by using a 4-sulfophthalic acid as an ionic crosslinker and sulfonating agent. Morphological and structural characterization by transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), energy-dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD) confirmed the successful synthesis of the doping agents and their incorporation into the polymer. The influence of PO4-TiO2 and SO4-TiO2 doping and their content on the physicochemical properties of the nanocomposite membranes was evaluated. Swelling degree and water uptake gradually reduced to 7% and 13%, respectively, with increasing doping agent concentration. Ion exchange capacity and ionic conductivity of the membrane with 3 wt.% doping agents were raised 5 and 7 times, respectively, compared to the undoped one. The thermal and oxidative stability and tensile strength also increased with the doping content. Furthermore, lower borohydride permeability (0.32 × 10−6 cm2 s−1) was measured for the membranes with higher amount of inorganic doping agents when compared to the undoped membrane (0.71 × 10−5 cm2 s−1) and Nafion®117 (0.40 × 10−6 cm2 s−1). These results pave the way for a green, simple and low-cost approach for the development of composite membranes for practical DBFCs.

scholarly journals Zeolite NaP1 Functionalization for the Sorption of Metal Complexes with Biodegradable N-(1,2-dicarboxyethyl)-D,L-aspartic Acid

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2518
Author(s):  
Dorota Kołodyńska ◽  
Yongming Ju ◽  
Małgorzata Franus ◽  
Wojciech Franus
Keyword(s):  
Experimental Data ◽  
Aspartic Acid ◽  
Ph Value ◽  
Complexing Agents ◽  
X Ray Diffraction ◽  
Experimental Conditions ◽  
Modified Zeolite ◽  
X Ray ◽  
Slow Release Fertilizers ◽  
Pseudo Second Order

The possibility of application of chitosan-modified zeolite as sorbent for Cu(II), Zn(II), Mn(II), and Fe(III) ions and their mixtures in the presence of N-(1,2-dicarboxyethyl)-D,L-aspartic acid, IDHA) under different experimental conditions were investigated. Chitosan-modified zeolite belongs to the group of biodegradable complexing agents used in fertilizer production. NaP1CS as a carrier forms a barrier to the spontaneous release of the fertilizer into soil. The obtained materials were characterized by Fourier transform infrared spectroscopy (FTIR); surface area determination (ASAP); scanning electron microscopy (SEM-EDS); X-ray fluorescence (XRF); X-ray diffraction (XRD); and carbon, hydrogen, and nitrogen (CHN), as well as thermogravimetric (TGA) methods. The concentrations of Cu(II), Zn(II), Mn(II), and Fe(III) complexes with IDHA varied from 5–20 mg/dm3 for Cu(II), 10–40 mg/dm3 for Fe(III), 20–80 mg/dm3 for Mn(II), and 10–40 mg/dm3 for Zn(II), respectively; pH value (3–6), time (1–120 min), and temperature (293–333 K) on the sorption efficiency were tested. The Langmuir, Freundlich, Dubinin–Radushkevich, and Temkin adsorption models were applied to describe experimental data. The pH 5 proved to be appropriate for adsorption. The pseudo-second order and Langmuir models were consistent with the experimental data. The thermodynamic parameters indicate that adsorption is spontaneous and endothermic. The highest desorption percentage was achieved using the HCl solution, therefore, proving that method can be used to design slow-release fertilizers.

Electrochemical Behavior of Direct Methanol Fuel Cells Based on Acidic Silica - Sulfonated Polysulfone Composite Membranes

2019 ◽  
Vol 41 (1) ◽  
pp. 2003-2009 ◽  
Author(s):  
Vincenzo Baglio ◽  
Francesco Lufrano ◽  
Orazio Di Blasi ◽  
Pietro Staiti ◽  
Vincenzo Antonucci ◽  
...  
Keyword(s):  
Fuel Cells ◽  
Electrochemical Behavior ◽  
Direct Methanol Fuel Cells ◽  
Composite Membranes ◽  
Sulfonated Polysulfone ◽  
Direct Methanol ◽  
Methanol Fuel Cells

Solid-state Thermoelectric Characteristics of NiII, FeII, CoII, and CuII Borohydrides

2021 ◽  
Author(s):  
Isam M. Arafa ◽  
Mazin Y. Shatnawi ◽  
Yousef N. Obeidallah ◽  
Ahmed K. Hijazi ◽  
Yaser A . Yousef
Keyword(s):  
Energy Transport ◽  
Waste Heat ◽  
Mixed Valence ◽  
Small Scale ◽  
X Ray Diffraction ◽  
Promising Candidate ◽  
X Ray ◽  
Cold Pressed ◽  
Thermal Energy Transport ◽  
Body Heat

Abstract Four transition metal borohydrides (MTBHs, MT = Ni, Fe, Co, and Cu) were prepared by sonicating a mixture of the desired MT salt with excess NaBH4 in a nonaqueous DMF/CH3OH media. The process afforded bimetallic (Ni-BH4), trimetallic (Fe-BH4, Co-BH4), and mixed-valence (Cu-H, Cu-BH4) amorphous, ferromagnetic nanoparticles as identified by thermal, ATR-IR, X-Ray diffraction, and magnetic susceptibility techniques. The electrical conductivity (σ) of cold-pressed discs of these MTBHs shows a nonlinear increase while their thermal conductivity (κ) decreases in the temperature range of 303 ≤ T ≤ 373 K. The thermal energy transport occurs through phonon lattice dynamics rather than electronic. The σ/κ ratio shows a nonlinear steep increase from 9.4 to 270 KV-2 in Ni-BH4, while a moderate-weak increase is observed for Fe-BH4, Co-BH4, and Cu-BH4. Accordingly, the corresponding thermoelectric (TE) parameters S, PF, ZT, and η were evaluated. All TE data shows that the bimetallic Ni-BH4 (S, 80 μVK-1; PF, 259 μWm-1K-2; ZT 0.64; η, 2.56%) is a better TE semiconductor than the other three MT-BHs investigated in this study. Our findings show that Ni-BH4 is a promising candidate to exploit low-temperature waste heat from body heat, sunshine, and small domestic devices for small-scale TE applications.

scholarly journals Fabrication and Characterization of Al/NiO Energetic Nanomultilayers

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
YiChao Yan ◽  
Wei Shi ◽  
HongChuan Jiang ◽  
Jie Xiong ◽  
WanLi Zhang ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Total Thickness ◽  
X Ray Diffraction ◽  
Dc Magnetron Sputtering ◽  
Metallic Oxide ◽  
Promising Candidate ◽  
X Ray ◽  
Thermal Boundary Conductance ◽  
Fabrication And Characterization

The redox reaction between Al and metallic oxide has its advantage compared with intermetallic reaction and Al/NiO nanomutlilayers are a promising candidate for enhancing the performance of energetic igniter. Al/NiO nanomutlilayers with different modulation periods are prepared on alumina substrate by direct current (DC) magnetron sputtering. The thicknesses of each period are 250 nm, 500 nm, 750 nm, 1000 nm, and 1500 nm, respectively, and the total thickness is 3 μm. The X-ray diffraction (XRD) and scanning electron microscope (SEM) results of the as-deposited Al/NiO nanomutlilayers show that the NiO films are amorphous and the layered structures are clearly distinguished. The X-ray photoelectron spectroscopy (XPS) demonstrates that the thickness of Al2O3increases on the side of Al monolayer after annealing at 450°C. The thermal diffusion time becomes greater significantly as the amount of thermal boundary conductance across the interfaces increases with relatively smaller modulation period. Differential scanning calorimeter (DSC) curve suggests that the energy release per unit mass is below the theoretical heat of the reaction due to the nonstoichiometric ratio between Al and NiO and the presence of impurities.

scholarly journals Theoretical study of the properties of X-ray diffraction moiré fringes. II. Illustration of angularly integrated moiré images

2019 ◽  
Vol 75 (4) ◽  
pp. 610-623
Author(s):  
Jun-ichi Yoshimura
Keyword(s):  
Incident Wave ◽  
Angular Width ◽  
X Ray Diffraction ◽  
Experimental Conditions ◽  
Acta Cryst ◽  
Low Contrast ◽  
X Ray ◽  
Moiré Fringes ◽  
Wide Range ◽  
Fringe Patterns

Using a theory of X-ray diffraction moiré fringes developed in a previous paper, labelled Part I [Yoshimura (2015). Acta Cryst. A71, 368–381], the X-ray moiré images of a silicon bicrystal having a weak curvature strain and an interspacing gap, assumed to be integrated for an incident-wave angular width, are simulation-computed over a wide range of crystal thicknesses and incident-wave angular width, likely under practical experimental conditions. Along with the simulated moiré images, the graphs of characteristic quantities on the moiré images are presented for a full understanding of them. The treated moiré images are all of rotation moiré. Mo Kα1 radiation and the 220 reflection were assumed in the simulation. The results of this simulation show that fringe patterns, which are significantly modified from simple straight fringes of rotation moiré, appear in some ranges of crystal thicknesses and incident-wave angular width, due to a combined effect of Pendellösung oscillation and an added phase difference from the interspacing gap, under the presence of a curvature strain. The moiré fringes which slope to the perpendicular direction to the diffraction vector in spite of the assumed condition of rotation moiré, and fringe patterns where low-contrast bands are produced with a sharp bend of fringes arising along the bands are examples of the modified fringe pattern. This simulation study provides a wide theoretical survey of the type of bicrystal moiré image produced under a particular condition.

Sign in / Sign up

Export Citation Format

Share Document