scholarly journals Study on the Corrosion Resistance of Graphene Oxide-Based Epoxy Zinc-Rich Coatings

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1657
Author(s):  
Yong Tian ◽  
Zhenxiao Bi ◽  
Gan Cui
Keyword(s):  
Corrosion Resistance ◽  
Graphene Oxide ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Open Circuit ◽  
Shielding Effect ◽  
Multiwall Carbon Nanotube ◽  
Pure Zinc ◽  
Modified Graphene Oxide ◽  
Multiwall Carbon

In order to improve the corrosion resistance of zinc-rich epoxy coatings and reduce the amount of zinc used, first, graphene oxide (GO) was modified by sulfonated multiwall carbon nanotubes (SMWCNTs) to obtain the modified graphene oxide (SM-GO). The samples were characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and Raman spectroscopy. Then, four kinds of coatings were prepared, namely pure zinc-rich coating (0-ZRC), graphene oxide-based zinc-rich coating (GO-ZRC), sulfonated multiwall carbon nanotube-based zinc-rich coating (SM-ZRC) and SM-GO-based zinc-rich coating (SG-ZRC). The corrosion resistance of the above coatings was studied by open circuit potential (OCP), electrochemical impedance spectroscopy (EIS), a salt spray test, 3D confocal microscope, and electron scanning electron microscope (SEM). The results indicate that GO is successfully non-covalently modified by SMWCNTs, of which the interlayer spacing increases and dispersion is improved. The order of the corrosion resistance is GO-ZRC > SG-ZRC > SM-ZRC > 0-ZRC. The addition of GO, SMWCNTs, and SM-GO increases the shielding effect and increases the electrical connection between Zn particles and metal substrates, which improves the corrosion resistance. However, SMWCNTs and SM-GO also strengthen the galvanic corrosion, which decreases the corrosion resistance to some extent.

scholarly journals Hydrophobic Modification of Graphene Oxide and Its Effect on the Corrosion Resistance of Silicone-Modified Epoxy Resin

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 89
Author(s):  
Wei Yuan ◽  
Qian Hu ◽  
Jiao Zhang ◽  
Feng Huang ◽  
Jing Liu
Keyword(s):  
Contact Angle ◽  
Corrosion Resistance ◽  
Graphene Oxide ◽  
Physical Properties ◽  
Epoxy Resin ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
X Ray ◽  
Modified Graphene Oxide ◽  
Modified Epoxy

This study modified graphene oxide (GO) with hydrophilic octadecylamine (ODA) via covalent bonding to improve its dispersion in silicone-modified epoxy resin (SMER) coatings. The structural and physical properties of ODA-GO were characterized by field-emission scanning electron microscopy (FE-SEM), X-ray diffraction analysis (XRD), Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and contact angle tests. The ODA-GO composite materials were added to SMER coatings by physical mixing. FE-SEM, water absorption, and contact angle tests were used to evaluate the physical properties of the ODA-GO/SMER coatings, while salt spray, electrochemical impedance spectroscopy (EIS), and scanning Kelvin probe (SKP) methods were used to test the anticorrosive performance of ODA-GO/SMER composite coatings on Q235 steel substrates. It was found that ODA was successfully grafted onto the surfaces of GO. The resulting ODA-GO material exhibited good hydrophobicity and dispersion in SMER coatings. The anticorrosive properties of the ODA-GO/SMER coatings were significantly improved due to the increased interfacial adhesion between the nanosheets and SMER, lengthening of the corrosive solution diffusion path, and increased cathodic peeling resistance. The 1 wt.% ODA-GO/SMER coating provided the best corrosion resistance than SMER coatings with other amounts of ODA-GO (including no addition). After immersion in 3.5 wt.% NaCl solution for 28 days, the low-frequency end impedance value of the 1 wt.% ODA-GO/SMER coating remained high, at 6.2 × 108 Ω·cm2.

Hydrothermal Surface Treatments with Cerium and Glycol Molecules on the AA 2024-T3 Clad Alloy

2016 ◽  
Vol 710 ◽  
pp. 216-221 ◽  
Author(s):  
Wagner Izaltino Alves Dos Santos ◽  
Isolda Costa ◽  
Célia Regina Tomachuk
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Electrochemical Techniques ◽  
Open Circuit ◽  
Self Healing ◽  
X Ray ◽  
Aa 2024 ◽  
New Treatment ◽  
New Treatments

New treatments for replacement of chromate require lower toxicity and corrosion protection. This study aims to investigate the influence of the combination of a Ce conversion coating (CCCe) with glycol molecules on the corrosion resistance of the AA2024-T3 clad (AA1230). The corrosion resistance of surface treated and untreated samples was evaluated by electrochemical techniques (electrochemical impedance spectroscopy, polarization tests and open circuit potential). These tests were complemented by salt spray tests to accelerate the corrosive effects of weathering. The surfaces were analyzed after corrosion tests by scanning electron microscopy with X-ray energy dispersive detector (SEM - EDX). The results of the CCCe samples in combination with glycol were compared with that of the surface with chromate layer and the results showed that the CCCe treatment is a candidate for replacement of chromating with the advantage that it does not generate toxic residues. The self-healing capacity of the new treatment tested was indicated by the increased formation of corrosion products deposition on top of Fe rich intermetallis in the AA1230 clad with time of exposure to the electrolyte.

scholarly journals Comparative Study on the Corrosion Resistance of 6061Al and SiC3D/6061Al Composite in a Chloride Environment

Materials ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 7730
Author(s):  
Liang Yu ◽  
Shuangshuang Hao ◽  
Xiaodong Nong ◽  
Xiuling Cao ◽  
Chen Zhang ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Specific Area ◽  
Open Circuit ◽  
Pressure Casting ◽  
Neutral Salt ◽  
Salt Leaching ◽  
Chloride Environment ◽  
Al Matrix

Interface problems and the destruction of the continuity of the oxide film in the Al matrix usually reduce the corrosion resistance of the material. In this paper, the corrosion resistance of Al matrix composites (AMCs) was improved by introducing the silicon carbide skeletons (SiC3D) obtained with polymer replica technology. SiC3D/6061Al was fabricated by infiltrating molten 6061Al alloy in the oxidized SiC3D using the low-pressure casting method. The corrosion resistance performances of 6061Al and SiC3D/6061Al in NaCl solution were studied by electrochemical, neutral salt spray corrosion (NSS), and salt leaching (SL) tests. Results show corrosion resistance of SiC3D/6061Al is higher than that of 6061Al alloys by open circuit potential (OCP), potentio-dynamic polarization (PDP), and electrochemical impedance spectroscopy (EIS) tests. However, NSS and SL tests show the corrosion resistance of SiC3D/6061Al is lower than that of 6061Al alloy. The reason is a corrosion resistant and anti-oxidation network macrostructure with large interface recombination, few concentrated interfaces, and a small specific area that formed in SiC3D/6061Al. SiC3D cannot damage the continuity of the Al2O3 passivating film, and the network macrostructure greatly improves the corrosion resistance performance.

Corrosion Behaviour of a Laser-MIG hybrid welding-brazing Joint of 6061 Aluminium Alloy to SUS304 Stainless Steel

CORROSION ◽  
10.5006/3866 ◽  
2021 ◽  
Author(s):  
ruilin liu ◽  
Yunqi Liu ◽  
Zheng Lei ◽  
Hui Tang ◽  
Shaoxiong He ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Weld Metal ◽  
Aluminium Alloy ◽  
Electrochemical Impedance ◽  
Corrosion Behaviour ◽  
Salt Spray ◽  
Chemical Properties ◽  
Open Circuit ◽  
Hybrid Welding

Lightweight steel-aluminium structures have broad application prospects because of their lowering weight characteristics, however, the corrosion of welding-brazing joints in steel-aluminium structures is less concerned or studied. In this paper, the corrosion behaviour of the Laser-MIG hybrid welding-brazing joints of steel-aluminium is investigated through the tests and analysis of salt spray, immersion and electrochemistry. The salt spray and immersion tests show that obvious galvanic corrosion occurs at the welded joints, in which the aluminium side is seriously corroded while the steel side is not corroded. The OCP values of the aluminium alloy and the weld metal are similar (approximately -0.48 V), and the stainless steel has a higher OCP value of -0.33 V. The corrosion resistance of the weld metal is lower than aluminium- as well as steel-base materials. The corrosion resistance of the joints is controlled by the aluminium alloy part of the two metals based on the open-circuit potential and EIS analysis. A possible corrosion process schematic for the physical/chemical properties of a welding-brazing joint immersed in a sodium chloride solution is proposed according to electrochemical impedance spectroscopy.

scholarly journals Preparation and Anti-Corrosive Properties of Waterborne Epoxy Composite Coating Containing Graphene Oxide Grafted with Sodium Tripolyphosphate

Coatings ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 307 ◽  
Author(s):  
Na Wang ◽  
Xu Yin ◽  
Jing Zhang ◽  
Huiying Gao ◽  
Xinlin Diao ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Sodium Tripolyphosphate ◽  
Salt Spray ◽  
Salt Spray Test ◽  
Coated Sample ◽  
X Ray ◽  
Waterborne Epoxy

In this paper, graphene oxide (GO) was grafted with sodium tripolyphosphate (STP) to achieve a new anti-corrosive pigment (STG) with homogenous dispersion in waterborne epoxy (EP). The results obtained from Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and X-ray Diffraction (XRD) revealed that STP was successfully combined with GO by chemical bonding. The corrosion resistance of EP, GO/EP and STG/EP coatings on carbon steel substrates was investigated via electrochemical impedance spectroscopy (EIS) and salt spray test. The EIS results showed that the impedance value of coating with 0.7 wt.% STG reached 1.019 × 109 Ω∙cm2, which was considerably higher than that of neat waterborne EP coatings. Salt spray test results revealed once again that STG (0.7 wt.%)/EP coating had superior corrosion resistance. Besides, the STG (0.7 wt.%)/EP coated sample showed the highest adhesion strength between coating and substrate.

scholarly journals Graphene Oxide Decorated with Titanium Nanoparticles to Reinforce the Anti-Corrosion Performance of Epoxy Coating

Coatings ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 129 ◽  
Author(s):  
Heng Yuan ◽  
Fugang Qi ◽  
Nie Zhao ◽  
Pengying Wan ◽  
Biao Zhang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Corrosion Resistance ◽  
Graphene Oxide ◽  
Composite Materials ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Corrosion Mechanism ◽  
X Ray ◽  
Ti Particles

Graphene oxide–titanium (GO-Ti) composite materials were fabricated using GO as a precursor and then anchoring nano titanium (Nano-Ti) particles on GO sheets with the help of a silane coupling agent. Then, the coating samples were prepared by dispersing GO, Nano-Ti particles, and GO-Ti in an epoxy resin at a low weight fraction of 1 wt %. The GO-Ti composites were investigated by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The dispersibility and anti-corrosion mechanism of the coatings were studied by sedimentation experiments, electrochemical impedance spectroscopy (EIS), SEM, and salt spray tests. The mechanical properties of the coatings were analyzed by friction and wear tests. The results showed that the Nano-Ti particles were successfully loaded on the GO surface by chemical bonds, which made GO-Ti composites exhibit better dispersibility in the epoxy than GO. Compared with Nano-Ti particles and GO, the GO-Ti composite exhibited significant advantages in improving the corrosion resistance of epoxy coatings at the same contents, which was attributed to the excellent dispersibility, inherent corrosion resistance, and sheet structure. Among the different proportions of composite materials, the GO-Ti (2:1) material exhibited the best dispersibility and corrosion resistance. In addition, the composite material also greatly improved the wear resistance of the coating.

scholarly journals Corrosion Resistance Test of Electroplated Gold and Palladium Using Fast Electrochemical Analysis

Coatings ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 405
Author(s):  
Walter Giurlani ◽  
Patrick Marcantelli ◽  
Francesco Benelli ◽  
Daniele Bottacci ◽  
Filippo Gambinossi ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Standardized Tests ◽  
Open Circuit Potential ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Corrosion Current ◽  
Electrochemical Analysis ◽  
Open Circuit ◽  
Metal Coatings ◽  
High Impedance

Noble metal coatings are commonly employed to improve corrosion resistance of metals in the electronic and jewellery industry. The corrosion resistance of electroplated goods is currently determinate with long, destructive and almost subjective interpretation corrosion tests in artificial atmosphere. In this study we present the application of electrochemical analysis to obtain fast and numerical information of the antiaging coating. We performed open circuit potential (OCP) and corrosion current measurement; we employed also the electrochemical impedance spectroscopy (EIS), commonly applied to organic or passivated metal with high-impedance, to find the best option for noble low-impedance coating analysis. For comparison, traditional standardized tests (damp heat ISO 17228, salt spray ISO 9227 and sulphur dioxide ISO 4524) were also performed.

scholarly journals Design and Multidimensional Screening of Flash-PEO Coatings for Mg in Comparison to Commercial Chromium(VI) Conversion Coating

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 337
Author(s):  
Ewa Wierzbicka ◽  
Marta Mohedano ◽  
Endzhe Matykina ◽  
Raul Arrabal
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Protection ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Conversion Coating ◽  
Neutral Salt ◽  
Chromium Vi ◽  
Alkaline Electrolytes ◽  
Az31b Alloy ◽  
Plasma Electrolytic

REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals) regulations demand for an expedient discovery of a Cr(VI)-free alternative corrosion protection for light alloys even though the green alternatives might never be as cheap as current harmful technologies. In the present work, flash- plasma electrolytic oxidation coatings (FPEO) with the process duration < 90 s are developed on AZ31B alloy in varied mixtures of silicate-, phosphate-, aluminate-, and fluoride-based alkaline electrolytes implementing current density and voltage limits. The overall evaluation of the coatings’ anticorrosion performance (electrochemical impedance spectroscopy (EIS), neutral salt spray test (NSST), paintability) shows that from nine optimized FPEO recipes, two (based on phosphate, fluoride, and aluminate or silicate mixtures) are found to be an adequate substitute for commercially used Cr(VI)-based conversion coating (CCC). The FPEO coatings with the best corrosion resistance consume a very low amount of energy (~1 kW h m−2 µm−1). It is also found that the lower the energy consumption of the FPEO process, the better the corrosion resistance of the resultant coating. The superb corrosion protection and a solid environmentally friendly outlook of PEO-based corrosion protection technology may facilitate the economic justification for industrial end-users of the current-consuming process as a replacement of the electroless CCC process.

scholarly journals Sacrificial Dissolution of Zinc Electroplated and Cold Galvanized Coated Steel in Saline and Soil Environments: A Comparison

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 744
Author(s):  
Ameeq Farooq ◽  
Umer Masood Chaudry ◽  
Ahsan Saleem ◽  
Kashif Mairaj Deen ◽  
Kotiba Hamad ◽  
...  
Keyword(s):  
Corrosion Rate ◽  
Electrochemical Impedance ◽  
Saline Soil ◽  
Steel Substrate ◽  
Salt Spray ◽  
Steel Structures ◽  
Open Circuit ◽  
Cyclic Polarization ◽  
Transfer Resistance ◽  
Soil Solutions

To protect steel structures, zinc coatings are mostly used as a sacrificial barrier. This research aims to estimate the dissolution tendency of the electroplated and zinc-rich cold galvanized (ZRCG) coatings of a controlled thickness (35 ± 1 μm) applied via brush and dip coating methods on the mild steel. To assess the corrosion behavior of these coated samples in 3.5% NaCl and 10% NaCl containing soil solutions, open circuit potential (OCP), cyclic polarization (CP), and electrochemical impedance spectroscopy (EIS) tests were performed. The more negative OCP and appreciably large corrosion rate of the electroplated and ZRCG coated samples in 3.5% NaCl solution highlighted the preferential dissolution of Zn coatings. However, in saline soil solution, the relatively positive OCP (>−850 mV vs. Cu/CuSO4) and lower corrosion rate of the electroplated and ZRCG coatings compared to the uncoated steel sample indicated their incapacity to protect the steel substrate. The CP scans of the zinc electroplated samples showed a positive hysteresis loop after 24 h of exposure in 3.5% NaCl and saline soil solutions attributing to the localized dissolution of the coating. Similarly, the appreciable decrease in the charge transfer resistance of the electroplated samples after 24 h of exposure corresponded to their accelerated dissolution. Compared to the localized dissolution of the electroplated and brush-coated samples, the dip-coated ZRCG samples exhibited uniform dissolution during the extended exposure (500 h) salt spray test.

Sign in / Sign up

Export Citation Format

Share Document