scholarly journals Effects of Gamma Radiation on the Sterility Assurance, Antibacterial Ability, and Biocompatibility of Impregnated Hydrogel Macrosphere Protein and Drug Release

Polymers ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 938
Author(s):  
Po-Sung Fu ◽  
Jen-Chyan Wang ◽  
Pei-Ling Lai ◽  
Shih-Ming Liu ◽  
Ya-Shun Chen ◽  
...  
Keyword(s):  
Drug Release ◽  
Water Absorption ◽  
In Vitro Release ◽  
Physicochemical Characteristics ◽  
High Rate ◽  
Γ Irradiation ◽  
Antibacterial Ability ◽  
Before And After ◽  
In Situ Hydrogel

Devices and medicines used in the medical field must be sterile. Gamma (γ)-irradiation is commonly used for sterilization because its high rate of penetration ensures uniform sterilization. To confirm that hydrogel macrosphere carriers inherit excellent liquid absorption with no cytotoxicity after γ-irradiation sterilization, investigating whether the physiochemical properties of hydrogel macrospheres differ before and after sterilization is essential. The present study evaluated the influence of the recommended 25-kGy γ-irradiation dose on the physicochemical characteristics and in vitro release of bovine serum albumin and vancomycin (an antibiotic medication) from alginate/gelatin with a w/w ratio of 1/4 crosslinking gel macrospheres. Gel macrosphere properties before and after sterilization were compared according to optical and scanning electron microscopy, infrared spectroscopy analysis, the amino residual crosslinking index, water absorption, degradation, sterility assurance, in vitro drug release, antibacterial ability, and cytotoxicity. The crosslinking index was almost unchanged; however, the γ-irradiation caused in situ hydrogel debonding and recrosslinking, which led to a decrease in the water absorption and increase in the degradation rate of the macrospheres after immersion. The release of gel macrospheres carrying vancomycin did not significantly affect antibacterial ability or biocompatibility after γ-irradiation. Accordingly, we conclude that γ-irradiation is suitable for macrospherical formulation.

scholarly journals Enhanced Treatment Effects of Tilmicosin Against Staphylococcus aureus Cow Mastitis by Self-Assembly Sodium Alginate-Chitosan Nanogel

Pharmaceutics ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 524 ◽  
Author(s):  
Kaixiang Zhou ◽  
Xiaofang Wang ◽  
Dongmei Chen ◽  
Yuanyuan Yuan ◽  
Shuge Wang ◽  
...  
Keyword(s):  
Staphylococcus Aureus ◽  
Self Assembly ◽  
In Vitro Release ◽  
Physicochemical Characteristics ◽  
The Novel ◽  
In Situ Hydrogel ◽  
Treatment Dosage ◽  
Normal Dosage

The Staphylococcus aureus (S. aureus) cow mastitis causes great losses to the cow industry. In order to improve the treatment effect of tilmicosin against cow mastitis, the combination of solid lipid nanoparticle (SLN) technology with in situ hydrogel technology was used to prepare the self-assembly tilmicosin nanogel (TIL-nanogel). The physicochemical characteristics, in vitro release, antibacterial activity and in vivo treatment efficacy of TIL-SLNs and TIL-nanogel were studied, respectively. The results showed the loading capacity (LC), encapsulation efficiency (EE), size, zeta potential and poly dispersion index (PDI) of TIL-nanogel were 23.33 ± 0.77%, 67.89 ± 3.01%, 431.57 ± 12.87 nm, 8.3 ± 0.06 mv and, 0.424 ± 0.032, respectively. The TIL-nanogel showed stronger sustained release in vitro than TIL-SLNs and commercial injection. The cure rate of half dosage and normal dosage of TIL-nanogel was 58.3% and 75.0%, which was higher than that of commercial injection (50.0%) at normal dosage. The results suggest that the treatment dosage of tilmicosin for cow mastitis could be reduced by TIL-nanogel. The novel TIL-nanogel will be beneficial by decreasing the usage of tilmicosin and the treatment costs of cow mastitis.

scholarly journals Doxycycline and Monocaprin In Situ Hydrogel: Effect on Stability, Mucoadhesion and Texture Analysis and In Vitro Release

Gels ◽  
2019 ◽  
Vol 5 (4) ◽  
pp. 47 ◽  
Author(s):  
Venu Gopal Reddy Patlolla ◽  
William Peter Holbrook ◽  
Sveinbjorn Gizurarson ◽  
Thordis Kristmundsdottir
Keyword(s):  
Drug Release ◽  
In Vitro Release ◽  
Fickian Diffusion ◽  
Release Time ◽  
Release Mechanism ◽  
Oral Diseases ◽  
Zero Order Kinetics ◽  
In Situ Hydrogel

The aim of this study was to develop a stable aqueous formulation containing a combination of doxycycline and monocaprin in clinically relevant concentrations. Increase in expression of Matrix metalloproteinases (MMPs) and microbial role in oral diseases is well established and the combination of above active ingredients could be potentially beneficial in treatment of oral mucosal conditions. The hydrogels containing different concentrations of doxycycline and monocaprin in the presence and absence of stabilizing excipients were developed and their stabilities were studied at 4 °C for up to 1 year. The drug–drug interaction was evaluated using Fourier-transform infrared spectroscopy (FTIR). The addition of monocaprin on doxycycline in situ hydrogel’s mucoadhesiveness, texture properties and drug release mechanism was studied. The addition of monocaprin negatively affected the doxycycline stability and was concentration dependent, whereas monocaprin was stable up to 1 year. Doxycycline did not interfere with the anti-Candidal activity of monocaprin. Furthermore, the presence of monocaprin significantly affected the formulation hardness, compressibility and adhesiveness. Monocaprin and doxycycline release followed zero order kinetics and the release mechanism was, by anomalous (non-Fickian) diffusion. The addition of monocaprin increased the drug release time and altered the release mechanism. It is possible to stabilize doxycycline in the presence of monocaprin up to 1 year at 4 °C.

scholarly journals Evaluation of physicochemical properties and in-vitro release profile of glipizide-matrix patch

2010 ◽  
Vol 46 (2) ◽  
pp. 213-218 ◽  
Author(s):  
Kajal Ghosal ◽  
Rajan Rajabalaya ◽  
Anindya Kishore Maiti ◽  
Bikramaditya Chowdhury ◽  
Arunabha Nanda
Keyword(s):  
Drug Release ◽  
Physicochemical Properties ◽  
Water Absorption ◽  
In Vitro Release ◽  
Fixed Amount ◽  
Weight Variation ◽  
Matrix Patches ◽  
Vitro Release ◽  
Matrix Patch

OBJECTIVES: The aim of the present investigation was to form matrix patches with ethyl cellulose (EC) as the base polymer, polyvinyl pyrrolidone (PVP) as the copolymer, plasticizer with dibutyl phthalate (DBP) or acetyl tributyl citrate (ATBC) and the drug glipizide (gz) by the solvent casting method. Physicochemical properties of the patches and in vitro drug release were determined in a modified Keshary-chien diffusion cell to optimize the patch formulations with the help of experimental data and figures for further studies. TECHNIQUES: EC and PVP of different proportions with different weight percentages of either DBP or ATBC and a fixed amount of glipizide were taken for matrix patch formations. The dried patches were used for measuring their drug contents as well as their thicknesses, tensile strengths, moisture contents and water absorption amounts in percentage. In vitro release amounts at different intervals were measured by UV-spectrophotometer. RESULTS: Drug contents varied from 96 - 99%. Thickness and tensile strength varied due to weight variation of the ingredients in the matrix patches. Moisture content and water absorption in wt % were greater for the patches containing higher amount of PVP due to its hydrophilic nature. Variations in drug release were observed among various formulations. It was found that all of the releases followed diffusion controlled zero order kinetics. Two DBP patches yielded better and more adequate release. CONCLUSIONS: The two formulations with DBP were the preferred choice for making matrix patches for further studies.

scholarly journals Preparation and Evaluation of Sustained Release Matrix Tablets of Tolterodine Tartrate Using Guggul Resin

2018 ◽  
Vol 21 (1) ◽  
pp. 24-34
Author(s):  
K Latha ◽  
T Chinni Kranthi ◽  
Naseeb Basha Shaik
Keyword(s):  
Drug Release ◽  
Sustained Release ◽  
In Vitro Release ◽  
Physicochemical Characteristics ◽  
Matrix Tablets ◽  
Natural Polymers ◽  
Duration Of Action ◽  
Tolterodine Tartrate ◽  
Vitro Release

The present study is based on preparation of sustained release matrix tablets of tolterodine tartrate (for overactive bladder treatment) using guggul resin. Tolterodine tartrate is a highly soluble drug, to increase the duration of action the release of the drug has to be sustained. Natural resin is used as a polymer to sustain the release of drug, which was isolated from guggul gum by petroleum ether. Natural polymers are economical, biodegradable and can be chemically modified. Different ratios of drug and guggul resin were tried in the formulation of sustained release matrix tablets of tolterodine tartrate. Wet granulation technique was adopted for preparation of tolterodine tartrate granules, showed good flow properties and compressibility. The fabricated tablets were evaluated for various physicochemical characteristics and in vitro release studies like hardness, thickness, weight variation, friability, drug content and content uniformity were found to be within the limits. The drug release of optimized formulation (F6) was fitted to various kinetic models and the R2 value is 0.988 and the n value of drug release is 0.787. Therefore, the drug release follows zero order with non-fickian diffusion. The mechanism of drug release involves erosion and diffusion. Stability studies were performed for the optimized formulation as per ICH guidelines climatic zone III and were found to be stable with insignificant changes in physicochemical characteristics and in vitro release studies.Bangladesh Pharmaceutical Journal 21(1): 24-34, 2018

Formulation and In vitro Release Characterization of Metoprolol Succinate Extended Release Tablets

2012 ◽  
Vol 4 (4) ◽  
pp. 1537-1543
Author(s):  
Sakthikumar T ◽  
Rajendran N N ◽  
Natarajan R
Keyword(s):  
Drug Release ◽  
Extended Release ◽  
In Vitro Release ◽  
Methyl Cellulose ◽  
Wet Granulation ◽  
Direct Compression ◽  
Metoprolol Succinate ◽  
Extended Release Formulations ◽  
Vitro Release

The present study was aimed to develop an extended release tablet of metoprolol Succinate for the treatment of hypertension.  Four extended release formulations F1-F4 were developed using varying proportions of hydroxylpropyl-methylcellulose K100M, sodium carboxy methyl cellulose and Eudragit L30 D55 by wet granulation. Five extended release formulations F5-F9 containing HPMC K100M and HPMC 5 cps in varying concentration were developed by direct compression. The physicochemical and in vitro release characteristics of all the formulations were investigated and compared. Two formulations, F7 and F8 have shown not more 25% drug release  in 1st h, 20%-40% drug release at 4th hour, 40%-60% drug release at 8th hour and not less than 80% at 20th hour and the release pattern conform with USP specification for 24 hours extended release formulation. It can be conclusively stated that optimum concentration of HPMC K100M (58%-65%) by direct compression method can yield an extended release of metoprolol succinate for 24 hours.

Design, Synthesis and Studies on Novel Polymeric Prodrugs of Erlotinib for Colon Drug Delivery

2020 ◽  
Vol 20 ◽  
Author(s):  
Sahil Kumar ◽  
Bandna Sharma ◽  
Tilak R. Bhardwaj ◽  
Rajesh K. Singh
Keyword(s):  
Drug Delivery ◽  
Colon Cancer ◽  
Drug Release ◽  
Anticancer Agents ◽  
Release Kinetics ◽  
In Vitro Release ◽  
Specific Treatment ◽  
Drug Conjugates ◽  
Polymer Drug Conjugates

Aims: In the present study, polymer-drug conjugates were synthesized based on azo-bond cleavage drug delivery approach for targeting erlotinib as anticancer drug specifically to the colon for the proficient treatment of colon cancer. Background: Colon cancer (CC) is the third commonly detected tumor worldwide and it make up about 10 % of all cases of cancers. Most of the chemotherapeutic drugs available for treating colon cancer are not only toxic to cancerous cells but also to the normal healthy cells. Among the various approaches to get rid of the adverse effects of anticancer agents, prodrugs are one of the most imperative approaches. Objective: The objective of the study is to chemically modify the erlotinib drug through azo-bond linkage and suitable spacer which will be finally linked to polymeric backbone to give desired polymer linked prodrug. The azo reductase enzyme present in colon is supposed to cleave the azo-bond specifically and augment the drug release at the colon. Methods: The synthesized conjugates were characterized by IR and 1H-NMR spectroscopy. The cleavage of aromatic azobond resulted in a potential colon-specific liberation of drug from conjugate studied in rat fecal contents. In vitro release profiles of polyphosphazene-linked conjugates of erlotinib have been studied at pH 1.2, pH 6.8 and pH 7.4. The stability study was designed to exhibit that free drug was released proficiently and unmodified from polyphosphazene-erlotinib conjugates having aromatic azo-bond in artificial colon conditions. Results: The synthesized conjugates were demonstrated to be stable in simulated upper gastro-intestinal tract conditions. The drug release kinetics shows that all the polymer-drug conjugates of erlotinib follow zero-order release kinetics which indicates that the drug release from the polymeric backbone is independent of its concentration. Kinetic study of conjugates with slope (n) shows the anomalous type of release with an exponent (n) > 0.89 indicating a super case II type of release. Conclusion: These studies indicate that polyphosphazene linked drug conjugates of erlotinib could be the promising candidates for the site-specific treatment of colon cancer with least detrimental side-effects.

Formulation and Characterization of Glimepiride Nanoparticles for Dissolution Enhancement

2020 ◽  
Vol 10 (5) ◽  
pp. 649-663
Author(s):  
Reena Siwach ◽  
Parijat Pandey ◽  
Harish Dureja
Keyword(s):  
Drug Release ◽  
Dissolution Rate ◽  
Oral Absorption ◽  
In Vitro Release ◽  
Entrapment Efficiency ◽  
Class Ii ◽  
Dissolution Enhancement ◽  
In Vitro Drug Release ◽  
Bcs Class Ii

Background: The rate-limiting step in the oral absorption of BCS class II drugs is dissolution. Their low solubility is one of the major obstacles in the process of drug development. Dissolution rate can be increased by decreasing the particle size to the nano range, eventually leading to increased bioavailability. Objective: : In the present study, glimepiride loaded nanoparticles were prepared to enhance the dissolution rate. The aim of the work was to examine the effect of polymer-drug ratio, solvent-antisolvent ratio and speed of mixing on in vitro release of glimepiride. Methods: Glimepiride is an antidiabetic drug belonging to the BCS class II drugs. The polymeric nanoparticles were formulated according to Box-Behnken Design (BBD) using nanoprecipitation technique. The prepared nanoparticles were evaluated for in vitro drug release, loading capacity, entrapment efficiency, and percentage yield. Result: It was found that NP-8 has maximum in vitro drug release and was selected as an optimized batch. Analysis of Variance (ANOVA) was applied to the in vitro drug release to study the fitness and significance of the model. The batch NP-8 showed 70.34 ± 1.09% in vitro drug release in 0.1 N methanolic HCl and 92.02 ± 1.87% drug release in phosphate buffer pH 7.8. The release data revealed that the nanoparticles followed zero order kinetics. Conclusion: The study revealed that the incorporation of glimepiride into gelucire 50/13 resulted in enhanced dissolution rate.

Preparation, evaluation, and in vitro release of chitosan-alginate tanshinone self-microemulsifying sustained-release microcapsules

2020 ◽  
pp. 1-9
Author(s):  
Yunhong Wang ◽  
Rong Hu ◽  
Yanlei Guo ◽  
Weihan Qin ◽  
Xiaomei Zhang ◽  
...  
Keyword(s):  
Drug Release ◽  
Sustained Release ◽  
Release Rate ◽  
Orthogonal Design ◽  
Drug Loading ◽  
In Vitro Release ◽  
Core Material ◽  
Evaluation Indexes ◽  
Vitro Release

OBJECTIVE: In this study we explore the method to prepare tanshinone self-microemulsifying sustained-release microcapsules using tanshinone self-microemulsion as the core material, and chitosan and alginate as capsule materials. METHODS: The optimal preparation technology of chitosan-alginate tanshinone self-microemulsifying sustained-release microcapsules was determined by using the orthogonal design experiment and single-factor analysis. The drug loading and entrapment rate were used as evaluation indexes to assess the quality of the drug, and the in vitro release rate was used to evaluate the drug release performance. RESULTS: The best technology of chitosan-alginate tanshinone self-microemulsifying sustained-release microcapsules is as follows: the concentration of alginate is 1.5%, the ratio of tanshinone self-microemulsion volume to alginate volume to chitosan mass is 1:1:0.5 (ml: ml: g), and the best concentration of calcium chloride is 2.0%. To prepare the microcapsules using this technology, the drug loading will be 0.046%, the entrapment rate will be 80.23%, and the 24-hour in vitro cumulative release rate will be 97.4%. CONCLUSION: The release of the microcapsules conforms to the Higuchi equation and the first-order drug release model and has a good sustained-release performance.

scholarly journals Cefotaxime Loaded Polycaprolactone Based Polymeric Nanoparticles with Antifouling Properties for In-Vitro Drug Release Applications

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2180
Author(s):  
Sana Javaid ◽  
Nasir M. Ahmad ◽  
Azhar Mahmood ◽  
Habib Nasir ◽  
Mudassir Iqbal ◽  
...  
Keyword(s):  
Drug Release ◽  
Polymeric Nanoparticles ◽  
In Vitro Release ◽  
Bacterial Strains ◽  
In Vitro Drug Release ◽  
Antifouling Activity ◽  
Polymeric Drug ◽  
Pure Drug ◽  
Average Size

The objective of the present study was to achieve the successful encapsulation of a therapeutic agent to achieve antifouling functionality regarding biomedical applications. Considering nanotechnology, drug-loaded polycaprolactone (PCL)-based nanoparticles were prepared using a nano-precipitation technique by optimizing various process parameters. The resultant nano-formulations were investigated for in vitro drug release and antifouling applications. The prepared particles were characterized in terms of surface morphology and surface properties. Optimized blank and drug-loaded nanoparticles had an average size of 200 nm and 216 nm, respectively, with associated charges of −16.8 mV and −11.2 mV. Studies of the in vitro release of drug were carried out, which showed sustained release at two different pH, 5.5 and 7.4 Antifouling activity was observed against two bacterial strains, Gram-positive Staphylococcus aureus and Gram-negative Escherichia coli. The zone of inhibition of the optimized polymeric drug-loaded nanoparticle F-25 against both strains were compared with the pure drug. The gradual pH-responsive release of antibiotics from the biodegradable polymeric nanoparticles could significantly increase the efficiency and pharmacokinetics of the drug as compared to the pure drug. The acquired data significantly noted that the resultant nano-encapsulation of antifouling functionality could be a promising candidate for topical drug delivery systems and skin applications.

scholarly journals Comparative Analysis of Morphological and Release Profiles in Ocular Implants of Acetazolamide Prepared by Electrospinning

Pharmaceutics ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 260
Author(s):  
Mariana Morais ◽  
Patrícia Coimbra ◽  
Maria Eugénia Pina
Keyword(s):  
Drug Release ◽  
In Vitro Release ◽  
Morbidity Rate ◽  
Coating Film ◽  
Sustained Drug Release ◽  
Coated Implant ◽  
Poly Ethylene ◽  
Coaxial Fibers ◽  
Release Profiles

The visual impairment that often leads to blindness causes a higher morbidity rate. The goal of this work is to create a novel biodegradable polymeric implant obtained from coaxial fibers containing the dispersed drug—acetazolamide—in order to achieve sustained drug release and increase patient compliance, which is of the highest importance. Firstly, during this work, uncoated implants were produced by electrospinning, and rolled in the shape of small cylinders that were composed of uniaxial and coaxial fibers with immobilized drug inside. The fibers were composed by PCL (poly ε-caprolactone) and Lutrol F127 (poly (oxyethylene-b-oxypropylene-b-oxyethylene)). The prepared implants exhibited a fast rate of drug release, which led to the preparation of new implants incorporating the same formulation but with an additional coating film prepared by solvent casting and comprising PCL and Lutrol F127 or PCL and Luwax EVA 3 ((poly (ethylene-co-vinyl acetate)). Implants were characterized and in vitro release profiles of acetazolamide were obtained in phosphate buffered saline (PBS) at 37 °C. The release profile of the acetazolamide from coated implant containing Luwax EVA 3 is considerably slower than what was observed in case of coated implants containing Lutrol F127, allowing a sustained release and an innovation relatively to other ocular drug delivery systems.

Sign in / Sign up

Export Citation Format

Share Document