scholarly journals Microfabrication with Very Low-Average Power of Green Light to Produce PDMS Microchips

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 607
Author(s):  
Lucero M. Hernandez-Cedillo ◽  
Francisco G. Vázquez-Cuevas ◽  
Rafael Quintero-Torres ◽  
Jose L. Aragón ◽  
Miguel Angel Ocampo Mortera ◽  
...  
Keyword(s):  
Low Cost ◽  
Average Power ◽  
Green Light ◽  
Microfluidic Devices ◽  
Processing Parameters ◽  
Coating Film ◽  
Two Dimensional ◽  
Dimethyl Siloxane ◽  
Visible Laser ◽  
High Absorption

In this article, we show an alternative low-cost fabrication method to obtain poly(dimethyl siloxane) (PDMS) microfluidic devices. The proposed method allows the inscription of micron resolution channels on polystyrene (PS) surfaces, used as a mold for the wanted microchip’s production, by applying a high absorption coating film on the PS surface to ablate it with a focused low-power visible laser. The method allows for obtaining micro-resolution channels at powers between 2 and 10 mW and can realize any two-dimensional polymeric devices. The effect of the main processing parameters on the channel’s geometry is presented.

scholarly journals Microfabrication With Very Low-Average Power of Green Light to Produce PDMS Microchips

2020 ◽  
Author(s):  
Lucero M. Hernandez -Cedillo ◽  
Francisco G. Vázquez-Cuevas ◽  
Rafael Quintero-Torres ◽  
Jose L. Aragón ◽  
Miguel Angel Ocampo Mortera ◽  
...  
Keyword(s):  
Low Cost ◽  
Average Power ◽  
Green Light ◽  
Microfluidic Devices ◽  
Processing Parameters ◽  
Coating Film ◽  
Two Dimensional ◽  
Dimethyl Siloxane ◽  
Visible Laser ◽  
High Absorption

In this letter, we show an alternative low-cost fabrication method to obtain poly(dimethyl siloxane) (PDMS) microfluidic devices. The proposed method allows the inscription of micron resolution channels on polystyrene (PS) surfaces, used as a mold for the wanted microchip’s production, by applying a high absorption coating film on the PS surface to ablate it with a focused low-power visible laser. The method allows obtaining micro resolution channels at powers between 2 and 10mW and can realize any two-dimensional polymeric devices. The effect of the main processing parameters on the channel’s geometry is presented.

Performance Analysis of Visible Light Communication Based on 16-QAM Companded OFDM Using Laser Diode

2020 ◽  
Vol 41 (2) ◽  
pp. 153-158
Author(s):  
Mangone Fall ◽  
Xiang Gao ◽  
Rui Deng ◽  
Zhangdui Zhong
Keyword(s):  
Laser Diode ◽  
Orthogonal Frequency Division Multiplexing ◽  
High Speed ◽  
Cumulative Distribution Function ◽  
Low Cost ◽  
Average Power ◽  
Visible Light Communication ◽  
Cumulative Distribution ◽  
Ofdm Signal ◽  
Visible Laser

AbstractIn this paper, a 16-QAM orthogonal frequency division multiplexing (OFDM) with companding technique is proposed and experimentally demonstrated in a high-speed visible laser light communication setup with low-cost 450 nm blue-light laser diode. Companding technique is used to reduce the high peak-to-average power ratio (PAPR) of the OFDM signal. The experimental results show a successfully achieved 2.5 Gb/s under 5 m free space transmission and a PAPR reduction of about 3.2 dB at a fixed complementary cumulative distribution function of 10–3 when compared with the regular one without any technique.

Ti3C2-MXene/Bismuth Ferrite Nanohybrids for Efficient Degradation of Organic Dye and Colorless Pollutant

2019 ◽  
Author(s):  
Ayesha Tariq ◽  
M. Abdullah Iqbal ◽  
S. Irfan Ali ◽  
Muhammad Z. Iqbal ◽  
Deji Akinwande ◽  
...  
Keyword(s):  
Surface Area ◽  
Low Cost ◽  
Bismuth Ferrite ◽  
Organic Dye ◽  
Two Dimensional ◽  
Electron Hole ◽  
Photocatalytic Application ◽  
Electron Hole Pair ◽  
Pair Generation ◽  
Photocatalytic Applications

<p>Nanohybrids, made up of Bismuth ferrites/Carbon allotropes, are extensively used in photocatalytic applications nowadays. Our work proposes a nanohybrid system composed of Bismuth ferrite nanoparticles with two-dimensional (2D) MXene sheets namely, the BiFeO<sub>3</sub> (BFO)/Ti<sub>3</sub>C<sub>2</sub> (MXene) nanohybrid for enhanced photocatalytic activity. We have fabricated the BFO/MXene nanohybrid using simple and low cost double solvent solvothermal method. The SEM and TEM images show that the BFO nanoparticles were attached onto the MXene surface and in the inter-layers of two-dimensional (2D) MXene sheets. The photocatalytic application is tested for the visible light irradiation which showed the highest efficiency among all pure-BFO based photocatalysts, i.e. 100% degradation in 42 min for organic dye (Congo Red) and colorless aqueous pollutant (acetophenone) in 150 min, respectively. The present BFO-based hybrid system exhibited the large surface area of 147 m<sup>2</sup>g<sup>-1</sup>measured via Brunauer-Emmett-Teller (BET) sorption-desorption technique, and is found to be largest among BFO and its derivatives. Also, the photoluminescence (PL) spectra indicate large electron-hole pair generation. Fast and efficient degradation of organic molecules is supported by both factors; larger surface area and lower electron-hole recombination rate. The BFO/MXene nanohybrid presented here is a highly efficient photocatalyst compared to other nanostructures based on pure BiFeO<sub>3</sub> which makes it a promising candidate for many future applications.</p>

AMANDA—low-cost production of microfluidic devices

1998 ◽  
Vol 70 (1-2) ◽  
pp. 153-158 ◽  
Author(s):  
W.K. Schomburg ◽  
R. Ahrens ◽  
W. Bacher ◽  
C. Goll ◽  
S. Meinzer ◽  
...  
Keyword(s):  
Low Cost ◽  
Microfluidic Devices

scholarly journals Development of an Additive Manufacturing System for the Deposition of Thermoplastics Impregnated with Carbon Fibers

2019 ◽  
Vol 3 (2) ◽  
pp. 35 ◽  
Author(s):  
Miguel Reis Silva ◽  
António M. Pereira ◽  
Nuno Alves ◽  
Gonçalo Mateus ◽  
Artur Mateus ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Additive Manufacturing ◽  
Carbon Fibers ◽  
Low Cost ◽  
Deposition Process ◽  
Processing Parameters ◽  
Yarn Diameter ◽  
Thermoplastic Matrix ◽  
Anisotropic Mechanical Properties ◽  
Long Carbon Fiber

This work presents an innovative system that allows the oriented deposition of continuous fibers or long fibers, pre-impregnated or not, in a thermoplastic matrix. This system is used in an integrated way with the filamentary fusion additive manufacturing technology and allows a localized and oriented reinforcement of polymer components for advanced engineering applications at a low cost. To demonstrate the capabilities of the developed system, composite components of thermoplastic matrix (polyamide) reinforced with pre-impregnated long carbon fiber (carbon + polyamide), 1 K and 3 K, were processed and their tensile and flexural strength evaluated. It was demonstrated that the tensile strength value depends on the density of carbon fibers present in the composite, and that with the passage of 2 to 4 layers of fibers, an increase in breaking strength was obtained of about 366% and 325% for the 3 K and 1 K yarns, respectively. The increase of the fiber yarn diameter leads to higher values of tensile strength of the composite. The obtained standard deviation reveals that the deposition process gives rise to components with anisotropic mechanical properties and the need to optimize the processing parameters, especially those that lead to an increase in adhesion between deposited layers.

Microwave-induced, thermally assisted solvent bonding for low-cost PMMA microfluidic devices

2009 ◽  
Vol 20 (1) ◽  
pp. 015026 ◽  
Author(s):  
Mona Rahbar ◽  
Sumanpreet Chhina ◽  
Dan Sameoto ◽  
M Parameswaran
Keyword(s):  
Low Cost ◽  
Microfluidic Devices ◽  
Solvent Bonding

Forming of Zeolite/Carbon Composite Substrate Coated with Titania for Photocatalyst Decomposition of Organic Compound

2015 ◽  
Vol 659 ◽  
pp. 304-309
Author(s):  
Khemmakorn Gomonsirisuk ◽  
Thanakorn Wasanapiarnpong
Keyword(s):  
Activated Carbon ◽  
Composite Materials ◽  
Low Cost ◽  
Carbon Composite ◽  
Phenolic Resins ◽  
Soaking Time ◽  
Naa Zeolite ◽  
Composite Substrate ◽  
Zeolite Composite ◽  
High Absorption

Organic contaminated wastes water from petrochemical industries can be removed by adsorbent and photocatalyst. In this work, the degradation rate of phenol have been studied at different ratios of activated carbon/NaA zeolite composite materials coated with TiO2 photocatalyst which are easily to be fabricated into tubular shape by extrusion method. In addition, the foam-inserted composite can be floated on the surface of waste water for the higher phocatalyst activity. While the composite is the low cost adsorbent with high absorption and high ion exchange properties. In order to optimize the efficiency of material, the various ratios of activated carbon/NaA zeolite (3:1, 1:1 and 1:3) and amount of coated TiO2 on the specimen’s surface was studied by UV/Vis spectrophotometer which related to phenol concentration. Moreover the various amount of phenolic resins (10, 20, 30, 40 and 50 wt%) at different reduction firing temperatures (600 and 650 °C) with soaking time of 1, 2 and 3 hours affected to the compressive strength of samples. For the characterization, XRD is used to characterize the phase and SEM is used to provide the morphology of the prepared composite materials.

Sign in / Sign up

Export Citation Format

Share Document