scholarly journals Mechanical Properties of Poly(ethylene-co-methacrylic acid) Reinforced with Carbon Fibers

Polymers ◽  
2021 ◽  
Vol 13 (1) ◽  
pp. 165
Author(s):  
Tatjana Haramina ◽  
Daniel Pugar ◽  
Darko Ivančević ◽  
Ivica Smojver
Keyword(s):  
Mechanical Properties ◽  
Carbon Fibers ◽  
Methacrylic Acid ◽  
Mass Fraction ◽  
Tensile Modulus ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Double Layers ◽  
The Matrix ◽  
Poly Ethylene

The capability of poly(ethylene-co-methacrylic acid) (E/MAA) to self-heal is well known, however, its mechanical properties are weak. In this study, composites with single and double layers of unidirectional (UD) carbon fibers were prepared by compression molding. Even a low mass fraction of fibers substantially improved the polymer. The flexural and tensile properties were tested at 0°, 45° and 90° fibers direction and compared to those of the matrix. The mechanical properties in the 0° direction proved superior. Flexural properties depended on the reinforcement distance from the stress neutral plane. The tensile modulus in the 0° direction was 13 times greater despite only a 2.5% mass fraction of fibers. However, both tensile modulus and strength were observed to degrade in the 90° direction. Dynamic mechanical analysis showed the dependence of both structure and properties on the thermal history of E/MAA. Tensile tests after ballistic impact showed that the modulus of the self-healed E/MAA was not affected, yet the strength, yield point, and particularly the elongation at break were reduced. A composite with higher fiber content could be prepared by mixing milled E/MAA particles in fibers prior to compression.

Wear Resistance and Mechanical Properties of Polymeric Fibers Filled with Inorganic Fillers

2006 ◽  
Vol 977 ◽  
Author(s):  
Toshihira Irisawa ◽  
Masatoshi Shioya ◽  
Haruki Kobayashi ◽  
Junichi Kaneko
Keyword(s):  
Mechanical Properties ◽  
Wear Resistance ◽  
Tensile Modulus ◽  
Nylon 6 ◽  
Polymeric Fibers ◽  
Poly Ethylene Terephthalate ◽  
The Matrix ◽  
Pet Fibers ◽  
Inorganic Fillers ◽  
Poly Ethylene

AbstractThe wear resistance and the mechanical properties of polymer matrix composite fibers filled with inorganic fillers have been investigated in order to find out the way to increase the wear resistance of the fibers without losing tensile modulus and strength. Nylon 6 and poly(ethylene terephthalate) have been used as the matrix polymer and aluminum borate whisker and carbon nanotube have been used as the fillers. The wear resistance of the fibers has been evaluated by observing the fiber cross section after the side of the fiber was worn using a rotating drum covered with abrasive paper. The wear resistance of the nylon 6 and PET fibers was increased by the addition of these fillers without the loss of tensile modulus and strength. The effects of the addition of the fillers on the wear resistance have been compared with the effects of stretching and heat treatment of the fibers.

Nano-HA Preparation and its Effects on Mechanical Properties of nHA/PLLA/PES Composite Biomaterials

2013 ◽  
Vol 668 ◽  
pp. 80-84
Author(s):  
Zhong Cheng Zhou ◽  
Xiong Jun Shen ◽  
Xin Fan ◽  
Qiu Mei Wu ◽  
Hai Lin Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Modulus ◽  
Tensile Tests ◽  
Content Increase ◽  
Short Axis ◽  
Melt Blending ◽  
Sem Images ◽  
Poly Ethylene ◽  
20 Nm ◽  
Hydroxyapatite Crystals

Nanocrystals hydroxyapatite (nHA) was synthesized and modified chemically, and nanocrystals hydroxyapatite / poly(L-lactide)/poly(ethylene succinate)(nHA/PLLA/PES) composite was prepared by melt-blending using nHA, PLLA and PES as reactants in a stainless steel chamber. The obtained nHA was of high purity and high crystallinity as well, its mean sizes measured from TEM observations were 65±35nm (long axis) and 40±10nm (short axis), and are close to the endosteal needle hydroxyapatite crystals size ((15 ~ 20) nm×60 nm) in the human body. The mechanical properties of nHA/ PLLA/PES blends were determined by bending and tensile tests and the effects of nHA content on the mechanical properties of nHA/PLLA/PES blends were investigated. The blending modulus and tensile modulus increase with the nHA (0,5,10,15and 20 wt.%) content increase, while blending strength increases up to HA mass fraction of 10% and after that decreases. SEM images revealed that the surface changed from rough to smooth with increasing nHA content, especially with nHA content higher than 20%, which implied the failure mechanism of the material changes from ductile to brittle.

scholarly journals Influence of Treated Distillate Aromatic Extract (TDAE) Content and Addition Time on Rubber-Filler Interactions in Silica Filled SBR/BR Blends

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 698
Author(s):  
Selin Sökmen ◽  
Katja Oßwald ◽  
Katrin Reincke ◽  
Sybill Ilisch
Keyword(s):  
Mechanical Properties ◽  
Oil Content ◽  
Tensile Modulus ◽  
Mechanical Analysis ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Binary Blends ◽  
Rubber Layer ◽  
Processing Aids ◽  
Rubber Filler

High compatibility and good rubber–filler interactions are required in order to obtain high quality products. Rubber–filler and filler–filler interactions can be influenced by various material factors, such as the presence of processing aids. Although different processing aids, especially the plasticizers, and their effects on compatibility have been investigated in the literature, their influence on rubber–filler interactions in highly active filler reinforced mixtures is not explicit and has not been investigated in depth. For this purpose, the influence of treated distillate aromatic extract (TDAE) oil content and its addition time on interactions between silica and rubber chains were investigated in this study. Rubber–filler and filler–filler interactions of uncured and cured silica-filled SBR/BR blends were characterized by using rubber layer L concept and dynamic mechanical analysis, whereas mechanical properties were studied by tensile test and Shore A hardness. Five parts per hundred rubber (phr) TDAE addition at 0, 1.5, and 3 min of mixing were characterized to investigate the influence of TDAE addition time on rubber–filler interactions. It was observed that addition time of TDAE can influence the development of bounded rubber structure and the interfacial interactions, especially at short time of mixing, less than 5 min. Oil addition with silica at 1.5 min of mixing resulted in fast rubber layer development and a small reduction in storage shear modulus of uncured blends. The influence of oil content on rubber–filler and filler–filler interactions were investigated for the binary blends without oil, with 5 and 20 phr TDAE content. The addition of 5 phr oil resulted in a slight increase in rubber layer and 0.05 MPa reduction in Payne effect of uncured blends. The storage tensile modulus of vulcanizates at small strains decreased from 13.97 to 8.28 MPa after oil addition. Twenty parts per hundred rubber (phr) oil addition to binary blends caused rubber layer L to decrease from 0.45 to 0.42. The storage tensile modulus of the vulcanizates and its reduction with higher amplitudes were incontrovertibly high among the vulcanizates with lower oil content, which were 13.57 and 4.49 MPa, respectively. When any consequential change in mechanical properties of styrene–butadiene rubber (SBR)/butadiene rubber (BR) blends could not be observed at different TDAE addition time, increasing amount of oil in blends enhanced elongation at break, and decreased Shore A hardness and tensile strength.

scholarly journals Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1242
Author(s):  
Olga Mysiukiewicz ◽  
Paulina Kosmela ◽  
Mateusz Barczewski ◽  
Aleksander Hejna
Keyword(s):  
Mechanical Properties ◽  
Melt Flow Index ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Flow Index ◽  
Scanning Calorimetry ◽  
Metal Composites ◽  
Pre Treatment ◽  
The Impact ◽  
Properties Of Composites

Investigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry), thermal (differential scanning calorimetry), as well as static (tensile tests, hardness, rebound resilience) and dynamic (dynamical mechanical analysis) mechanical properties of composites were investigated. The incorporation of 1 and 2 wt% of aluminum filler resulted in small enhancements of mechanical properties, while loadings of 5 and 10 wt% provided materials with a similar performance to neat HDPE. Such results were supported by the lack of disturbances in the rheological behavior of composites. The presented results indicate that a significant content of aluminum filler may be introduced into the HDPE matrix without additional pre-treatment and does not cause the deterioration of composites’ performance, which should be considered beneficial when engineering PE/metal composites.

Enhancing the Thermal and Mechanical Characteristics of Polyvinyl Alcohol (PVA)-Hemp Protein Particles (HPP) Composites

2021 ◽  
Vol 36 (2) ◽  
pp. 137-143
Author(s):  
S. A. Awad
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperatures ◽  
Composite Films ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Decomposition Temperature ◽  
Scanning Calorimetry ◽  
Solution Casting Method ◽  
Protein Particles

Abstract This paper aims to describe the thermal, mechanical, and surface properties of a PVA/HPP blend whereby the film was prepared using a solution casting method. The improvements in thermal and mechanical properties of HPP-based PVA composites were investigated. The characterization of pure PVA and PVA composite films included tensile tests, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The results of TGA and DSC indicated that the addition of HPP increased the thermal decomposition temperature of the composites. Mechanical properties are significantly improved in PVA/HPP composites. The thermal stability of the PVA composite increased with the increase of HPP filler content. The tensile strength increased from 15.74 ± 0.72 MPa to 27.54 ± 0.45 MPa and the Young’s modulus increased from 282.51 ± 20.56 MPa to 988.69 ± 42.64 MPa for the 12 wt% HPP doped sample. Dynamic mechanical analysis (DMA) revealed that at elevated temperatures, enhanced mechanical properties because of the presence of HPP was even more noticeable. Morphological observations displayed no signs of agglomeration of HPP fillers even in composites with high HPP loading.

BRIDGING OF CARBON FIBERS IN CF/EPOXY COMPOSITES USING ELECTROSTATICALLY INDUCED CNT ALIGNMENT

2021 ◽  
Author(s):  
DANDAN ZHANG ◽  
XINGKANG SHE ◽  
YIPENG HE ◽  
WESLEY A. CHAPKIN, ◽  
VI T. BREGMAN ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Electric Field ◽  
Carbon Fibers ◽  
Hybrid Composites ◽  
Tensile Modulus ◽  
Tensile Tests ◽  
Polymer Mixture ◽  
Ac Electric Field ◽  
Reinforced Polymer ◽  
Electric Field Direction

Carbon fiber reinforced polymer (CFRP) composites are lightweight materials with superior strength but are expensive due to the increased cost of carbon fibers (CFs). The addition of carbon nanotubes (CNTs) to polymer nanocomposites are becoming an excellent alternative to CF due to their unique combination of electrical, thermal, and mechanical properties. With the application of an electric field across the CNT/polymer mixture before curing, CNTs will not only be aligned along the electric field direction, but also form networks after reaching to a certain degree of alignment. In this study, an alternating current (AC) electric field was applied continuously to CNT/CF/Epoxy hybrid composites before curing. By cutting off the applied voltage when the monitored electric current increased, the degree of networking of CNTs between two CF tows was controlled. The relative electric field strength around the end of conductive carbon fiber tows in the epoxy matrix was modeled using COMSOL Multiphysics. It increased after applying AC electric field parallel to the CF tows, thereby increasing the alignment degree of CNTs and building a network to bridge the CF tows. The preliminary results indicate that the microhardness and tensile modulus between two CF tows are increased due to the networking of CNTs in this area. The fracture surface of the specimens after tensile tests were characterized to reveal more details of the microstructure.

Physico Chemical Characterization of Nanofibrous Poly(Ε-Caprolactone) Electrospun Templates for Cell Adhesion

MRS Advances ◽  
2017 ◽  
Vol 2 (49) ◽  
pp. 2689-2694
Author(s):  
Karla A. Gaspar-Ovalle ◽  
Juan V. Cauich-Rodriguez ◽  
Armando Encinas
Keyword(s):  
Mechanical Properties ◽  
Differential Scanning Calorimetry ◽  
Cell Adhesion ◽  
Tensile Modulus ◽  
Chemical Characterization ◽  
Mechanical Analysis ◽  
Scanning Calorimetry ◽  
Water Contact ◽  
Physico Chemical ◽  
Static Water

ABSTRACTNanofibrous mats of poly ε-caprolactone (PCL) were fabricated by electrospinning. The nanofiber structures were investigated and characterized by scanning electron microscope, differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical analysis, static water-contact-angle analysis and mechanical properties. The results showed that the nanofibrous PCL is an ideal biopolymer for cell adhesion, owing to its biocompatibility, biodegradability, structural stability and mechanical properties. Differential scanning calorimetry results showed that the fibrous structure of PCL does not alter its crystallinity. Studies of the mechanical properties, wettability and degradability showed that the structure of the electrospun PCL improved the tensile modulus, tensile strength, wettability and biodegradability of the nanotemplates. To evaluate the nanofibrous structure of PCL on cell adhesion, osteoblasts cells were seeded on these templates. The results showed that both adhesion and proliferation of the cells is viable on these electrospun PCL membranes. Thus electrospinning is a relatively inexpensive and scalable manufacturing technique for submicron to nanometer diameter fibers, which can be of interest in the commodity industry.

scholarly journals Polymeric Composites Based on Polyurea Matrix Reinforced with Carbon Nanotubes

2017 ◽  
Vol 54 (1) ◽  
pp. 41-44 ◽  
Author(s):  
Maria Adina Vulcan ◽  
Celina Damian ◽  
Paul Octavian Stanescu ◽  
Eugeniu Vasile ◽  
Razvan Petre ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Thermal Stability ◽  
Scanning Electron Microscopy ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Scanning Electron

This paper deals with the synthesis of polyurea and its use as polymer matrix for nanocomposites reinforced with multi-walled carbon nanotubes (MWCNT). Two types of materials were obtained during this research, the first cathegory uses the polyurea as matrix and the second one uses a mixture between epoxy resin and polyurea. The nanocomposites were characterized by Thermogravimetric Analysis (TGA), Dynamic Mechanical Analysis (DMA), Scanning Electron Microscopy (SEM) and Tensile Tests .The elastomeric features of nanocomposites were highlighted by the results which showed low value of Tg. Also higher thermal stability with ~40oC compared with commercial products (M20) were observed, but lower mechanical properties compared to neat polyurea.

scholarly journals The effect of isothermal crystallization on mechanical properties of poly(ethylene 2,5-furandicarboxylate)

e-Polymers ◽  
2021 ◽  
Vol 22 (1) ◽  
pp. 1-11
Author(s):  
Wei Zhang ◽  
Qingyin Wang ◽  
Gongying Wang ◽  
Shaoying Liu
Keyword(s):  
Mechanical Properties ◽  
Intrinsic Viscosity ◽  
Crystallization Temperature ◽  
Isothermal Crystallization ◽  
Tensile Modulus ◽  
Optical Microscope ◽  
Crystallization Time ◽  
Scanning Calorimetry ◽  
Crystallization Properties ◽  
Poly Ethylene

Abstract The effects of isothermal crystallization temperature/time on mechanical properties of bio-based polyester poly(ethylene 2,5-furandicarboxylate) (PEF) were investigated. The intrinsic viscosity, crystallization properties, thermal properties, and microstructure of PEF were characterized using ubbelohde viscometer, X-ray diffraction, polarizing optical microscope, differential scanning calorimetry, and scanning electron microscopy. The PEF sample isothermal crystallized at various temperatures for various times was denoted as PEF-T-t. The results showed that the isothermal crystallization temperature affected the mechanical properties of PEF-T-30 by simultaneously affecting its crystallization properties and intrinsic viscosity. The isothermal crystallization time only affected the crystallization properties of PEF-110-t. The crystallinity of PEF-110-40 was 17.1%. With small crystal size, poor regularity, and α′-crystal, PEF-110-40 can absorb the energy generated in the tensile process to the maximum extent. Therefore, the best mechanical properties can be obtained for PEF-110-40 with the tensile strength of 43.55 MPa, the tensile modulus of 1,296 MPa, and the elongation at a break of 13.36%.

The Structure and Mechanical Properties of Plastically Consolidated Al-Ni Alloy

2016 ◽  
Vol 682 ◽  
pp. 245-251 ◽  
Author(s):  
Grzegorz Włoch ◽  
Tomasz Skrzekut ◽  
Jakub Sobota ◽  
Antoni Woźnicki ◽  
Justyna Cisoń
Keyword(s):  
Mechanical Properties ◽  
Vickers Hardness ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Intermetallic Phases ◽  
Scanning Calorimetry ◽  
Porosity Formation ◽  
X Ray ◽  
Ni Alloy ◽  
Thermal Stability Of

Mixed and preliminarily consolidated powders of aluminium and nickel (90 mass % Al and 10 mass % Ni) were hot extruded. As results the rod, 8 mm in diameter, was obtained. As-extruded material was subjected to the microstructural investigations using scanning electron microscopy (SEM/EDS) and X-ray analysis (XRD). The differential scanning calorimetry (DSC) and thermo-mechanical analysis (TMA) were also performed. The mechanical properties of as extruded material were determined by the tensile test and Vickers hardness measurements. In order to evaluate the thermal stability of PM alloy, samples were annealed at the temperature of 475 and 550 °C. After annealing Vickers hardness measurements and tensile tests were carried out. The plastic consolidation of powders during extrusion was found to be very effective, because no pores or voids were observed in the examined material. The detailed microstructural investigations and XRD analyses did not reveal the presence of the intermetallic phases in the as-extruded material. During annealing, the Al3Ni intermetallic compound was formed as the result of chemical reaction between the alloy components. The hardness of the alloy after annealing at the temperature of 475°C was found to be comparable to the hardness in as-extruded state. Annealing of the material at the temperature of 550°C results in hardness decreasing by about 50%, as the consequence of porosity formation and Al3Ni cracking.

Sign in / Sign up

Export Citation Format

Share Document