scholarly journals Additive Manufacturing of Polyether Ether Ketone (PEEK) for Space Applications: A Nanosat Polymeric Structure

Polymers ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 11
Author(s):  
Marianna Rinaldi ◽  
Federico Cecchini ◽  
Lucia Pigliaru ◽  
Tommaso Ghidini ◽  
Francesco Lumaca ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Material Selection ◽  
Raw Material ◽  
Space Applications ◽  
Printing Process ◽  
Polymeric Structure ◽  
Fused Deposition ◽  
Polyether Ether Ketone ◽  
3D Printed ◽  
Ether Ketone

Recent improvements in additive layer manufacturing (ALM) have provided new designs of geometrically complex structures with lighter materials and low processing costs. The use of additive manufacturing in spacecraft production is opening up many new possibilities in both design and fabrication, allowing for the reduction of the weight of the structure subsystems. In this aim, polymeric ALM structures can become a choice, in terms of lightweight and demisability, as far as good thermomechanical properties. Moreover, provided that fused-deposition modeling (FDM) is used, nanosats and other structures could be easily produced in space. However, the choice of the material is a crucial step of the process, as the final performance of the printed parts is strongly dependent on three pillars: design, material, and printing process. As a high-performance technopolymer, polyether ether ketone (PEEK) has been adopted to fabricate parts via ALM; however, the space compatibility of 3D-printed parts remains not demonstrated. This work aimed to realize a nanosat polymeric structure via FDM, including all the phases of the development process: thermomechanical design, raw material selection, printing process tuning, and manufacturing of a proof of concept of a technological model. The design phase includes the application of topology optimization to maximize mass saving and take full advantage of the ALM capability. 3D-printed parts were characterized via thermomechanical tests, outgassing tests of 3D-printed parts are reported confirming the outstanding performance of polyether ether ketone and its potential as a material for structural space application.

scholarly journals 3D Printed Masks for Powders and Viruses Safety Protection Using Food Grade Polymers: Empirical Tests

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 617
Author(s):  
Ruben Foresti ◽  
Benedetta Ghezzi ◽  
Matteo Vettori ◽  
Lorenzo Bergonzi ◽  
Silvia Attolino ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Additive Manufacturing ◽  
Material Selection ◽  
Mechanical Resistance ◽  
Biological Safety ◽  
Fused Deposition ◽  
Industrial Grade ◽  
Safety Protection ◽  
3D Printed ◽  
Manufacturing Technologies

The production of 3D printed safety protection devices (SPD) requires particular attention to the material selection and to the evaluation of mechanical resistance, biological safety and surface roughness related to the accumulation of bacteria and viruses. We explored the possibility to adopt additive manufacturing technologies for the production of respirator masks, responding to the sudden demand of SPDs caused by the emergency scenario of the pandemic spread of SARS-COV-2. In this study, we developed different prototypes of masks, exclusively applying basic additive manufacturing technologies like fused deposition modeling (FDM) and droplet-based precision extrusion deposition (db-PED) to common food packaging materials. We analyzed the resulting mechanical characteristics, biological safety (cell adhesion and viability), surface roughness and resistance to dissolution, before and after the cleaning and disinfection phases. We showed that masks 3D printed with home-grade printing equipment have similar performances compared to the industrial-grade ones, and furthermore we obtained a perfect face fit by customizing their shape. Finally, we developed novel approaches to the additive manufacturing post-processing phases essential to assure human safety in the production of 3D printed custom medical devices.

scholarly journals Parameters Influencing the Outcome of Additive Manufacturing of Tiny Medical Devices Based on PEEK

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 466 ◽  
Author(s):  
Yiqiao Wang ◽  
Wolf-Dieter Müller ◽  
Adam Rumjahn ◽  
Andreas Schwitalla
Keyword(s):  
Medical Devices ◽  
Fused Deposition Modeling ◽  
High Accuracy ◽  
Design Parameters ◽  
Fused Deposition ◽  
Polyether Ether Ketone ◽  
Deposition Modeling ◽  
3D Printed ◽  
Ether Ketone

In this review, we discuss the parameters of fused deposition modeling (FDM) technology used in finished parts made from polyether ether ketone (PEEK) and also the possibility of printing small PEEK parts. The published articles reporting on 3D printed PEEK implants were obtained using PubMed and search engines such as Google Scholar including references cited therein. The results indicate that although many have been experiments conducted on PEEK 3D printing, the consensus on a suitable printing parameter combination has not been reached and optimized parameters for printing worth pursuing. The printing of reproducible tiny-sized PEEK parts with high accuracy has proved to be possible in our experiments. Understanding the relationships among material properties, design parameters, and the ultimate performance of finished objects will be the basis for further improvement of the quality of 3D printed medical devices based on PEEK and to expand the polymers applications.

scholarly journals Effect of Porosity on Mechanical Properties of 3D Printed Polymers: Experiments and Micromechanical Modeling Based on X-Ray Computed Tomography Analysis

Polymers ◽  
2019 ◽  
Vol 11 (7) ◽  
pp. 1154 ◽  
Author(s):  
Wang ◽  
Zhao ◽  
Fuh ◽  
Lee
Keyword(s):  
Computed Tomography ◽  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Fused Deposition Modeling ◽  
Micromechanical Model ◽  
Micromechanical Modeling ◽  
X Ray ◽  
Fused Deposition ◽  
3D Printed ◽  
X Ray Computed

Additive manufacturing (commonly known as 3D printing) is defined as a family of technologies that deposit and consolidate materials to create a 3D object as opposed to subtractive manufacturing methodologies. Fused deposition modeling (FDM), one of the most popular additive manufacturing techniques, has demonstrated extensive applications in various industries such as medical prosthetics, automotive, and aeronautics. As a thermal process, FDM may introduce internal voids and pores into the fabricated thermoplastics, giving rise to potential reduction on the mechanical properties. This paper aims to investigate the effects of the microscopic pores on the mechanical properties of material fabricated by the FDM process via experiments and micromechanical modeling. More specifically, the three-dimensional microscopic details of the internal pores, such as size, shape, density, and spatial location were quantitatively characterized by X-ray computed tomography (XCT) and, subsequently, experiments were conducted to characterize the mechanical properties of the material. Based on the microscopic details of the pores characterized by XCT, a micromechanical model was proposed to predict the mechanical properties of the material as a function of the porosity (ratio of total volume of the pores over total volume of the material). The prediction results of the mechanical properties were found to be in agreement with the experimental data as well as the existing works. The proposed micromechanical model allows the future designers to predict the elastic properties of the 3D printed material based on the porosity from XCT results. This provides a possibility of saving the experimental cost on destructive testing.

scholarly journals Tribological Characterization of Polyether Ether Ketone (PEEK) Polymers Produced by Additive Manufacturing for Hydrodynamic Bearing Application

Lubricants ◽  
2021 ◽  
Vol 9 (11) ◽  
pp. 112
Author(s):  
Davide Massocchi ◽  
Giacomo Riboni ◽  
Nora Lecis ◽  
Steven Chatterton ◽  
Paolo Pennacchi
Keyword(s):  
Additive Manufacturing ◽  
Optical Microscope ◽  
Wear Volume ◽  
Coating Materials ◽  
Hydrodynamic Bearing ◽  
Polyether Ether Ketone ◽  
Strength Tests ◽  
Ether Ketone ◽  
Tribological Characterization

The coating materials commonly used in hydrodynamic bearings are the so-called “Babbitt metals” or “white metals”, as defined by ASTM B23-00. Their low Young’s modulus and yield point have encouraged researchers to find new coatings to overcome these limitations. In this paper, the friction and wear of PEEK are studied in a dry sliding environment (without lubrication) using a ball-on-disk tribometer and compared to those of Babbitt metal. Furthermore, the bond strength tests between PEEK and metals/alloys are evaluated. PEEK polymer samples were obtained from cylindrical rods, manufactured by an innovative process for polymer bonding on bearing surfaces, using additive manufacturing technology. The morphologies of the degraded surfaces were examined using a high-resolution metallurgical optical microscope (OM) and a scanning electron microscope (SEM). The coefficients of friction (CoF) were obtained under the alternating ball-on-disk dry tribometer. The results of the experimental activity show that PEEK polymers have CoFs of about 0.22 and 0.16 under the 1 and 5 N applied load, respectively. The CoF and wear volume loss results are reported and compared to the reference Babbitt coating.

scholarly journals EFFECT OF EXTRUSION PROCESS PARAMETERS ON MECHANICAL PROPERTIES OF 3D PRINTED PLA PRODUCT

2021 ◽  
Vol 6 (2) ◽  
pp. 119
Author(s):  
Nanang Ali Sutisna ◽  
Rakha Amrillah Fattah
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Fused Deposition Modeling ◽  
Extrusion Process ◽  
Experimental Procedure ◽  
Fused Deposition ◽  
Novel Approach ◽  
Deposition Modeling ◽  
3D Printed ◽  
3D Digital Models

The method of producing items through synchronously depositing material level by level, based on 3D digital models, is named Additive Manufacturing (AM) or 3D-printing. Amongs many AM methods, the Fused Deposition Modeling (FDM) technique along with PLA (Polylactic acid) material is commonly used in additive manufacturing. Until now, the mechanical properties of the AM components could not be calculated or estimated until they've been assembled and checked. In this work, a novel approach is suggested as to how the extrusion process affects the mechanical properties of the printed component to obtain how the parts can be manufactured or printed to achieve improved mechanical properties. This methodology is based on an experimental procedure in which the combination of parameters to achieve an optimal from a manufacturing experiment and its value can be determined, the results obtained show the effect of the extrusion process affects the mechanical properties.

scholarly journals Strength Comparison of FDM 3D Printed PLA Made by Different Manufacturers

TEM Journal ◽  
2020 ◽  
pp. 966-970
Author(s):  
Damir Hodžić ◽  
Adi Pandžić ◽  
Ismar Hajro ◽  
Petar Tasić
Keyword(s):  
Experimental Study ◽  
Additive Manufacturing ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Manufacturing Technique ◽  
Plastic Materials ◽  
Wide Range ◽  
3D Printed ◽  
The Difference ◽  
Printing Parameters

Widely used additive manufacturing technique for plastic materials is Fused Deposition Modelling (FDM). The FDM technology has gained interest in industry for a wide range of applications, especially today when large number of different materials on the market are available. There are many different manufacturers for the same FDM material where the difference in price goes up to 50%. This experimental study investigates possible difference in strength of the 3D printed PLA material of five different manufacturers. All specimens are 3D printed on Ultimaker S5 printer with the same printing parameters, and they are all the same colour.

scholarly journals Effects of Thermal Cycle and Ultraviolet Radiation on 3D Printed Carbon Fiber/Polyether Ether Ketone Ablator

Aerospace ◽  
2020 ◽  
Vol 7 (7) ◽  
pp. 95
Author(s):  
Farhan Abdullah ◽  
Kei-ichi Okuyama ◽  
Akito Morimitsu ◽  
Naofumi Yamagata
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Uv Radiation ◽  
Thermal Cycle ◽  
Temperature Behavior ◽  
Heat Shield ◽  
Polyether Ether Ketone ◽  
Peek Composite ◽  
3D Printed ◽  
Ether Ketone

The extreme heating environment during re-entry requires an efficient heat shield to protect a spacecraft. The current method of manufacturing a heat shield is labor intensive. The application of 3D printing can reduce cost and manufacturing time and improve the quality of a heat shield. A 3D printed carbon fiber/polyether ether ketone (CF/PEEK) composite was proposed as a heat shield material. The aim was to develop a heat shield and the structural member as a single structure while maintaining the necessary recession resistance. Test samples were exposed to thermal cycles and ultraviolet (UV) radiation environment. Subsequently, a tensile test was performed to evaluate the effect of thermal cycle and UV radiation on the mechanical properties. The sample’s recession performance and temperature behavior were evaluated using an arc heated wind tunnel. Exposure to thermal cycle and UV radiation have limited effect on the mechanical properties, recession behavior and temperature behavior of 3D CF/PEEK. Results from the arc heating test showed an expansion of the sample surface and better recession resistance than other existing ablator materials. Overall, 3D CF/PEEK has excellent recession resistance while maintaining mechanical properties when exposed to high temperature, thermal cycle and UV radiation.

scholarly journals Surface Preparation and Treatment for Large-Scale 3D-Printed Composite Tooling Coating Adhesion

Coatings ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 457 ◽  
Author(s):  
Philipp Sauerbier ◽  
James Anderson ◽  
Douglas Gardner
Keyword(s):  
Additive Manufacturing ◽  
Large Scale ◽  
Lower Cost ◽  
Numerical Control ◽  
Fused Deposition Modelling ◽  
Filler Materials ◽  
Coating Adhesion ◽  
Fused Deposition ◽  
Composite Tooling ◽  
3D Printed

Recent advances in large-scale thermoplastic additive manufacturing (AM), using fused deposition modelling (FDM), have shown that the technology can effectively produce large aerospace tools with common feed stocks, costing 2.3 $/kg, such as a 20% carbon-filled acrylonitrile butadiene styrene (ABS). Large-scale additive manufacturing machines have build-volumes in the range of cubic meters and use commercially available pellet feedstock thermoplastics, which are significantly cheaper (5–10 $/kg) than the filament feedstocks for desktop 3D printers (20–50 $/kg). Additionally, large-scale AM machines have a higher material throughput on the order of 50 kg/h. This enables the cost-efficient tool production for several industries. Large-scale 3D-printed tooling will be computerized numerical control (CNC)-machined and -coated, to provide a surface suitable for demolding the composite parts. This paper outlines research undertaken to review and improve the adhesion of the coating systems to large, low-cost AM composite tooling, for marine or infrastructure composite applications. Lower cost tooling systems typically have a lower dimensional accuracy and thermal operating requirements than might be required for aerospace tooling. As such, they can use lower cost commodity grade thermoplastics. The polymer systems explored in the study included polypropylene (PP), styrene-maleic anhydride (SMA), and polylactic acid (PLA). Bio-based filler materials were used to reduce cost and increase the strength and stiffness of the material. Fillers used in the study included wood flour, at 30% by weight and spray-dried cellulose nano-fibrils, at 20% by weight. Applicable adhesion of the coating was achieved with PP, after surface treatment, and untreated SMA and PLA showed desirable coating adhesion results. PLA wood-filled composites offered the best properties for the desired application and, furthermore, they have environment-friendly advantages.

Sign in / Sign up

Export Citation Format

Share Document