scholarly journals Fabrication and Characterization of Cellulose Nanofiber Aerogels Prepared via Two Different Drying Techniques

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2583 ◽  
Author(s):  
Zhe Wang ◽  
Wenkai Zhu ◽  
Runzhou Huang ◽  
Yang Zhang ◽  
Chong Jia ◽  
...  
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Liquid Nitrogen ◽  
Compression Strength ◽  
Pore Volume ◽  
Supercritical Co2 ◽  
Freeze Drying ◽  
Drying Method ◽  
Drying Techniques ◽  
Supercritical Co2 Drying

Studies on the influence of drying processes on cellulose nanofiber (CNF) aerogel performance has always been a great challenge. In this study, CNF aerogels were prepared via two different drying techniques. The CNF solution was prepared via existing chemical methods, and the resultant aerogel was fabricated through supercritical CO2 drying and liquid nitrogen freeze-drying techniques. The microstructure, shrinkage, specific surface area, pore volume, density, compression strength, and isothermal desorption curves of CNF aerogel were characterized. The aerogel obtained from the liquid nitrogen freeze-drying method showed a relatively higher shrinkage, higher compression strength, lower specific surface area, higher pore volume, and higher density. The N2 adsorption capacity and pore diameter of the aerogel obtained via the liquid nitrogen freeze-drying method were lower than the aerogel that underwent supercritical CO2 drying. However, the structures of CNF aerogels obtained from these two drying methods were extremely similar.

Fuels Desulphurisation by Adsorbtion on Fe / Bentonite

2017 ◽  
Vol 68 (3) ◽  
pp. 483-486
Author(s):  
Constantin Sorin Ion ◽  
Mihaela Bombos ◽  
Gabriel Vasilievici ◽  
Dorin Bombos
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Pore Diameter ◽  
Adsorption Process ◽  
Continuous System ◽  
Gas Oil ◽  
Average Pore ◽  
Atmospheric Distillation

Desulfurisation of atmospheric distillation gasoline and gas oil was performed by adsorption process on Fe/ bentonite. The adsorbent was characterized by determining the adsorption isotherms, specific surface area, pore volume and average pore diameter. Adsorption experiments of atmospheric distillation gasoline and gas oil were performed in continuous system at 280�320oC, 5 atm and volume hourly space velocities of 1�2 h-1. The efficiency of adsorption on Fe / bentonite was better at desulphurisation of gasoline versus gas oil.

scholarly journals Nanometer Pore Structure Characterization of Taiyuan Formation Shale in the Lin-Xing Area Based on Nitrogen Adsorption Experiments

Minerals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 298
Author(s):  
Chenlong Ding ◽  
Jinxian He ◽  
Hongchen Wu ◽  
Xiaoli Zhang
Keyword(s):  
Specific Surface ◽  
Pore Structure ◽  
Surface Area ◽  
Specific Surface Area ◽  
Shale Gas ◽  
Pore Volume ◽  
Ordos Basin ◽  
Total Pore Volume ◽  
Nitrogen Adsorption ◽  
Taiyuan Formation

Ordos Basin is an important continental shale gas exploration site in China. The micropore structure of the shale reservoir is of great importance for shale gas evaluation. The Taiyuan Formation of the lower Permian is the main exploration interval for this area. To examine the nanometer pore structures in the Taiyuan Formation shale reservoirs in the Lin-Xing area, Northern Shaanxi, the microscopic pore structure characteristics were analyzed via nitrogen adsorption experiments. The pore structure parameters, such as specific surface area, pore volume, and aperture distribution, of shale were calculated; the significance of the pore structure for shale gas storage was analyzed; and the main controlling factors of pore development were assessed. The results indicated the surface area and hole volume of the shale sample to be 0.141–2.188 m2/g and 0.001398–0.008718 cm3/g, respectively. According to the IUPAC (International Union of Pure and Applied Chemistry) classification, mesopores and macropores were dominant in the pore structure, with the presence of a certain number of micropores. The adsorption curves were similar to the standard IV (a)-type isotherm line, and the hysteresis loop type was mainly similar to H3 and H4 types, indicating that most pores are dominated by open type pores, such as parallel plate-shaped pores and wedge-shaped slit pores. The micropores and mesopores provide the vast majority of the specific surface area, functioning as the main area for the adsorption of gas in the shale. The mesopores and macropores provide the vast majority of the pore volume, functioning as the main storage areas for the gas in the shale. Total organic carbon had no notable linear correlation with the total pore volume and the specific surface area. Vitrinite reflectance (Ro) had no notable correlation with the specific surface area, but did have a low “U” curve correlation with the total pore volume. There was no relationship between the quartz content and specific surface area and total pore volume. In addition, there was no notable correlation between the clay mineral content and total specific surface area and total pore volume.

Soil water repellency in sandy soil depends on the soil drying method, incubation temperature and specific surface area

Geoderma ◽  
2021 ◽  
Vol 402 ◽  
pp. 115264
Author(s):  
Enoch V.S. Wong ◽  
Philip R. Ward ◽  
Daniel V. Murphy ◽  
Matthias Leopold ◽  
Louise Barton
Keyword(s):  
Specific Surface ◽  
Soil Water ◽  
Surface Area ◽  
Specific Surface Area ◽  
Sandy Soil ◽  
Incubation Temperature ◽  
Water Repellency ◽  
Soil Drying ◽  
Drying Method ◽  
Soil Water Repellency

scholarly journals Titanium Carbide Nanocrystals Synthesized from a Metatitanic Acid-Sucrose Precursor via a Carbothermal Reduction

2015 ◽  
Vol 2015 ◽  
pp. 1-11 ◽  
Author(s):  
Hyunho Shin ◽  
Jun-Ho Eun
Keyword(s):  
Process Control ◽  
Titanium Carbide ◽  
Specific Surface ◽  
Surface Area ◽  
Pore Volume ◽  
Carbothermal Reduction ◽  
Crystal Size ◽  
Reduction Process ◽  
Specific Pore Volume ◽  
Metatitanic Acid

A TiC powder is synthesized from a micron-sized mesoporous metatitanic acid-sucrose precursor (precursor M) by a carbothermal reduction process. Control specimens are also prepared using a nanosized TiO2-sucrose precursor (precursor T) with a higher cost. When synthesized at 1500°C for 2 h in flowing Ar, the characteristics of the synthesized TiC from precursor M are similar to those of the counterpart from precursor T in terms of the crystal size (58.5 versus 57.4 nm), oxygen content (0.22 wt% versus 0.25 wt%), and representative sizes of mesopores: approximately 2.5 and 19.7–25.0 nm in both specimens. The most salient differences of the two specimens are found in the TiC from precursor M demonstrating (i) a higher crystallinity based on the distinctive doublet peaks in the high-two-theta XRD regime and (ii) a lower specific surface area (79.4 versus 94.8 m2/g) with a smaller specific pore volume (0.1 versus 0.2 cm3/g) than the counterpart from precursor T.

The relationship between geotechnical index properties and the pore-size distribution of compacted clayey silts

2015 ◽  
Vol 22 (6) ◽  
Author(s):  
Nazile Ural
Keyword(s):  
Specific Surface ◽  
Pore Size Distribution ◽  
Pore Size ◽  
Size Distribution ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Correlation Coefficients ◽  
Liquid Limit ◽  
Index Properties

AbstractIn this study, the relationships between geotechnical index properties and the pore-size distribution of compacted natural silt and artificial soil mixtures, namely, silt with two different clays and three different clay percentages (10%, 20%, and 40%), were examined and compared. Atterberg’s limit tests, standard compaction tests, mercury intrusion porosimetry, X-ray diffraction, scanning electron microscopy (SEM) analysis, and Brunauer-Emmett-Teller specific surface analysis were conducted. The results show that the liquid limit, the cumulative pore volume, and specific surface area of artificially mixed soils increase with an increase in the percentage of clay. The cumulative pore volume and specific surface area with geotechnical index properties were compared. High correlation coefficients were observed between the specific areas and both the liquid limit and the plasticity index, as well as between the cumulative pore volume and both the clay percentage and the

Study of the Porous Structure and High Adsorption Capacity of Biomass-Based Activated Carbon Prepared from Aspen Wood by Ferric Nitrate III Activation

2021 ◽  
Vol 15 (2) ◽  
pp. 131-144
Author(s):  
Chunjiang Jin ◽  
Huimin Chen ◽  
Luyuan Wang ◽  
Xingxing Cheng ◽  
Donghai An ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Mass Ratio ◽  
Aspen Wood ◽  
Surface Functional Groups ◽  
Wood Sawdust

In this study, aspen wood sawdust was used as the raw material, and Fe(NO3)3 and CO2 were used as activators. Activated carbon powder (ACP) was produced by the one-step physicochemical activation method in an open vacuum tube furnace. The effects of different mass ratios of Fe(NO3)3 and aspen wood sawdust on the pore structure of ACP were examined under single-variable experimental conditions. The mass ratio was 0–0.4. The detailed characteristics of ACP were examined by nitrogen adsorption, scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. The adsorption capacity of ACP was established by simulating volatile organic compounds (VOCs) using ethyl acetate. The results showed that ACP has a good nanostructure with a large pore volume, specific surface area, and surface functional groups. The pore volume and specific surface area of Fe-AC-0.3 were 0.26 cm3/g and 455.36 m2/g, respectively. The activator played an important role in the formation of the pore structure and morphology of ACP. When the mass ratio was 0–0.3, the porosity increased linearly, but when it was higher than 0.3, the porosity decreased. For example, the pore volume and specific surface area of Fe-AC-0.4 reached 0.24 cm3/g and 430.87 m2/g, respectively. ACP presented good VOC adsorption performance. The Fe-AC-0.3 sample, which contained the most micropore structures, presented the best adsorption capacity for ethyl acetate at 712.58 mg/g. Under the action of the specific reaction products nitrogen dioxide (NO2) and oxygen, the surface of modified ACP samples showed different rich C/O/N surface functional groups, including C-H, C=C, C=O, C-O-C, and C-N.

scholarly journals Effects of microwave modification on the desulfurization and denitrification of activated coke

BioResources ◽  
2020 ◽  
Vol 16 (1) ◽  
pp. 729-746
Author(s):  
Junhong Zhang ◽  
Zhi-jun He ◽  
Qing Guo ◽  
De-chao Xiao ◽  
Wen-long Zhan
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Surface Functional Groups ◽  
Characteristic Peak ◽  
Theoretical Support ◽  
O2 Concentration ◽  
Activated Coke ◽  
Oh Content

Microwave modification of activated coke is reported as a green and simple route to improve its synergistic desulfurization and denitrification. The results showed that microwave irradiation improved the specific surface area and pore volume, decreased the pore size, and activated the surface functional groups of the activated coke. Under the conditions of a microwave power of 500 W and a modification time of 30 min, the specific surface area was increased from 185.9 m2/g to 351.7 m2/g, the pore volume increased from 0.042 m3/g to 0.111 m3/g, and the characteristic peak strengths of C=C and -OH drastically increased. When the reaction temperature was 140 °C and the O2 concentration was 10% (by volume), the desulfurization and denitrification efficiency were maintained at levels greater than 90% and 80% for 30 min and 15 min, respectively. The C-O content increased, and the C=C and -OH content decreased after undergoing desulfurization and denitrification. The desulfurization and denitrification products were primarily sulfate and nitrate. This provides theoretical support for the application of microwave modified active coke in low temperature desulfurization and denitrification.

scholarly journals Structural and fractal characterization of adsorption pores of middle–high rank coal reservoirs in western Yunnan and eastern Guizhou: An experimental study of coals from the Panguan syncline and Laochang anticline

2018 ◽  
Vol 37 (1) ◽  
pp. 251-272 ◽  
Author(s):  
Junjian Zhang ◽  
Chongtao Wei ◽  
Gaoyuan Yan ◽  
Guanwen Lu
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Pore Diameter ◽  
Structural Parameters ◽  
Total Pore Volume ◽  
Type A ◽  
Type B ◽  
Type C

To better understand the structural characteristic of adsorption pores (pore diameter < 100 nm) of coal reservoirs around the coalbed methane production areas of western Yunnan and eastern Guizhou, we analyzed the structural and fractal characteristics of pore size range of 0.40–2.0 nm and 2–100 nm in middle–high rank coals ( Ro,max = 0.93–3.20%) by combining low-temperature N2/CO2 adsorption tests and surface/volume fractal theory. The results show that the coal reservoirs can be divided into three categories: type A ( Ro,max < 2.15%), type B (2.15% <  Ro,max <2.50%), and type C ( Ro,max > 2.15%). The structural parameters of pores in the range from 2 to 100 nm are influenced by the degree of coal metamorphism and the compositional parameters (e.g., ash and volatile matter). The dominant diameters of the specific surface areas are 10–50 nm, 2–50 nm, and 2–10 nm, respectively. The pores in the range from <2 nm provide the largest proportion of total specific surface area (97.22%–99.96%) of the coal reservoir, and the CO2-specific surface area and CO2-total pore volume relationships show a positive linear correlation. The metamorphic degree has a much greater control on the pores (pore diameter less than 2 nm) structural parameters than those of the pore diameter ranges from 2 to 100 nm. Dv1 and Dv2 can characterize the structure of 2–100 nm adsorption pores, and Dv1 (volume heterogeneity) has a positive correlation with the pore structural parameters such as N2-specific surface area and N2-total pore volume. This parameter can be used to characterize volume heterogeneity of 2–10 nm pores. Dv2 (surface heterogeneity) showed type A > type B > type C and was mainly affected by the metamorphism degree. Ds2 can be used to characterize the pore surface heterogeneity of micropores in the range of 0.62–1.50 nm. This parameter has a good correlation with the pore parameters (CO2-total pore volume, CO2-specific surface area, and average pore size) and is expressed as type C < type B < type A. In conclusion, the heterogeneity of the micropores is less than that of the meso- and macropores (2–100 nm). Dv1, Dv2, and Ds2 can be used as effective parameters to characterize the pore structure of adsorption pores. This result can provide a theoretical basis for studying the pore structure compatibility of coal reservoirs in the region.

Investigation of the methane adsorption characteristics of marine organic-rich shale: A case study of the lower Cambrian Niutitang Shale in the Fenggang block, northern Guizhou Province, South China

2018 ◽  
Vol 6 (4) ◽  
pp. T819-T833 ◽  
Author(s):  
Yang Gu ◽  
Wenlong Ding ◽  
Min Yin ◽  
Ruyue Wang ◽  
Baocheng Jiao ◽  
...  
Keyword(s):  
Specific Surface ◽  
Pore Size ◽  
Adsorption Capacity ◽  
Surface Area ◽  
South China ◽  
Pore Volume ◽  
Lower Cambrian ◽  
Methane Adsorption ◽  
Guizhou Province ◽  
Average Value

The marine shale in South China has great gas exploration potential, and exploration in the Sichuan Basin has been successful, but the degree of exploration remains low in the Guizhou Province. We used organic geochemical analyses (total organic carbon content and kerogen type), scanning electron microscopy (SEM), field emission SEM, nuclear magnetic resonance (NMR), X-ray diffraction analysis, and low-temperature [Formula: see text] and [Formula: see text] adsorption experimental methods to study the micropore types and pore structures and their effects on the methane adsorption capacity of organic-rich shales found in the Fenggang block in northern Guizhou Province. The results indicate that the microscopic surface porosity of the lower Cambrian Niutitang Formation ranges from 2.88% to 5.34%, with an average value of 3.86%. Based on nitrogen adsorption methods, the range of the average pore size distribution is 4.6–9.491 nm, with an average value of 6.68 nm. All of the samples exhibit significant unimodal distributions. The main pore size is less than 10 nm, and these pores account for most of the mesopore volume, which is generally consistent with the NMR results. The methane adsorption capacity of the shale samples gradually increases in the range of 0–8 MPa at 30°C and reaches a maximum at approximately 10 MPa. Positive correlations were found between the gas content and specific surface area, total pore volume, and micropore volume. These strong correlations indicate that the Niutitang Shale has a high specific surface area, a high pore volume, and narrow-diameter pores, demonstrating that it has a high gas adsorption capacity. The results of this study provide valuable information regarding the adsorption characteristics of marine shales and the factors that affect those characteristics.

Sign in / Sign up

Export Citation Format

Share Document