scholarly journals Biopolymeric Membrane Enriched with Chitosan and Silver for Metallic Ions Removal

Polymers ◽  
2020 ◽  
Vol 12 (8) ◽  
pp. 1792 ◽  
Author(s):  
Simona Căprărescu ◽  
Roxana Gabriela Zgârian ◽  
Graţiela Teodora Tihan ◽  
Violeta Purcar ◽  
Eugenia Eftimie Totu ◽  
...  
Keyword(s):  
Contact Angle ◽  
Synthetic Wastewater ◽  
Polymeric Membrane ◽  
Polymer Mixture ◽  
Gravimetric Analysis ◽  
Iron Ions ◽  
Treatment Rate ◽  
Excellent Thermal Stability ◽  
Angle Measurements ◽  
Contact Angle Measurements

The present paper synthesized, characterized, and evaluated the performance of the novel biopolymeric membrane enriched with cellulose acetate and chitosan (CHI)-silver (Ag) ions in order to remove iron ion from the synthetic wastewater using a new electrodialysis system. The prepared membranes were characterized by Fourier Transforms Infrared Spectroscopy-Attenuated Total Reflection (FTIR-ATR), Thermal Gravimetric Analysis (TGA) and Differential Thermal Analysis (DSC), contact angle measurements, microscopy studies, and electrochemical impedance spectroscopy (EIS). The electrodialysis experiments were performed at the different applied voltages (5, 10, and 15 V) for one hour, at room temperature. The treatment rate (TE) of iron ions, current efficiency (IE), and energy consumption (Wc) were calculated. FTIR-ATR spectra evidenced that incorporation of CHI-Ag ions into the polymer mixture led to a polymer-metal ion complex formation within the membrane. The TGA-DSC analysis for the obtained biopolymeric membranes showed excellent thermal stability (>350 °C). The contact angle measurements demonstrated the hydrophobic character of the polymeric membrane and a decrease of it by CHI-Ag adding. The EIS results indicated that the silver ions induced a higher ionic electrical conductivity. The highest value of the iron ions treatment rate (>60%) was obtained for the biopolymeric membrane with CHI-Ag ions at applied voltage of 15 V.

scholarly journals Investigation of the Ultraviolet Irradiation on Blend Films of PS/PCL

2021 ◽  
Vol 6 (2) ◽  
pp. 29-33
Author(s):  
João de Deus Pereira De Moraes Segundo ◽  
Maria Oneide Silva De Moraes ◽  
Catarina Barbosa Levy ◽  
Walter Ricardo Brito
Keyword(s):  
Contact Angle ◽  
Ultraviolet Light ◽  
Room Temperature ◽  
Polymer Mixture ◽  
Blend Films ◽  
Mechanical Stirring ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Poly Caprolactone ◽  
Mechanical Rotation

In this work, an investigation was carried out on the effect of ultraviolet light on different films. Polystyrene (PS), poly (caprolactone) (PCL), and blended films of PS/PCL were produced. Ethyl acetate (AE) was used as a solvent, and PS and PCL solutions were prepared by dissolving 250 mg in 2.5mL of AE under mechanical stirring at room temperature. The blended solutions of PS/PCL (PS:PCL) were prepared with different mass proportions, such as 90:10, 80:20, 70:30, and 60:40 into 2.5 mL of EA. The solutions were dripped with 500 µL on a glass substrate, and the films were produced with mechanical rotation of N=2000 RPM for 15 seconds using a Spin coater. The films were submitted to ultraviolet light for t=60 minutes and morphologically analyzed by optical microscopy, chemically by IR spectroscopy, and superficially by contact angle and wettability; this last analysis also investigated the effect of ultraviolet light at t=0, t=30, and t=60 minutes. The exposure of ultraviolet light on the films affected its morphologies. IR spectra showed that the photodegradation increased for larger PCL amounts into the blend. The contact angle measurements showed that after exposure to ultraviolet light, the hydrophobicity of the films increased. Therefore, the presence of PCL in the polymer mixture promoted the photodegradation of the PS/PCL films, making it attractive for developing new packaging.

Wettability Determination by Equilibrium Contact Angle Measurements: Reservoir Rock- Connate Water System With Injection of CO2

2012 ◽  
Author(s):  
Narjes Shojaikaveh ◽  
Cas Berentsen ◽  
Susanne Eva Johanne Rudolph-Floter ◽  
Karl Heinz Wolf ◽  
William Richard Rossen
Keyword(s):  
Contact Angle ◽  
Water System ◽  
Reservoir Rock ◽  
Equilibrium Contact Angle ◽  
Connate Water ◽  
Angle Measurements ◽  
Contact Angle Measurements

Surface Wettability Enhances Osteoblast Adhesion on Silicon-Substituted Hydroxyapatite Thin Films

2007 ◽  
Vol 330-332 ◽  
pp. 877-880 ◽  
Author(s):  
E.S. Thian ◽  
J. Huang ◽  
Serena Best ◽  
Zoe H. Barber ◽  
William Bonfield
Keyword(s):  
Thin Films ◽  
Contact Angle ◽  
Actin Filaments ◽  
Culture Study ◽  
Cell Culture Study ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Osteoblast Adhesion ◽  
Lower Contact

Crystalline hydroxyapatite (HA) and 0.8 wt.% silicon-substituted HA (SiHA) thin films were produced using magnetron co-sputtering. These films were subjected to contact angle measurements and in vitro cell culture study using human osteoblast-like (HOB) cells. A wettability study showed that SiHA has a lower contact angle, and thus is more hydrophilic in nature, as compared to HA. Consequently, enhanced cell growth was observed on SiHA at all time-points. Furthermore, distinct and well-developed actin filaments could be seen within HOB cells on SiHA. Thus, this work demonstrated that the surface properties of the coating may be modified by the substitution of Si into the HA structure.

Characterization of plasma-treated poly (hydroxybutyrate) membrane surfaces by ESCA and contact angle measurements

1992 ◽  
Vol 73 (2-3) ◽  
pp. 163-172 ◽  
Author(s):  
Dietmar Flösch ◽  
Giorgio Clarotti ◽  
Kurt E. Geckeler ◽  
François Schué ◽  
Wolfgang Göpel
Keyword(s):  
Contact Angle ◽  
Membrane Surfaces ◽  
Angle Measurements ◽  
Contact Angle Measurements

scholarly journals Surface Modification of the Alloy Ti-7.5Mo by Anodization for Biomedical Applications

2016 ◽  
Vol 869 ◽  
pp. 913-917 ◽  
Author(s):  
Ana Lucia do Amaral Escada ◽  
Javier Andres Muñoz Chaves ◽  
Ana Paula Rosifini Alves Claro
Keyword(s):  
Contact Angle ◽  
Electron Microscope ◽  
Biomedical Applications ◽  
Anatase Phase ◽  
Ammonium Fluoride ◽  
X Ray ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Simple Surface ◽  
Scanning Electron

The purpose of this study was to evaluate the TiO2 nanotubes growth and the variation in its diameter to improve the surface properties of Ti-7.5Mo to use for biomedical applications. For the nanotubes TiO2 growth, the samples were anodized in glycerol and ammonium fluoride and divided according to the anodizing potential at 5V to 10V and 24 hour time. The surfaces were examined by scanning electron microscope (SEM), X-ray analysis (XRD) and contact angle measurements. The average tube diameter, ranging in size from 13 to 23 nm, was found to increase with increasing anodizing voltage. It was also observed a decrease in contact angle in accordance with the increase in the anodizing potential. The X-ray analysis showed the presence of anatase phase in samples whose potential was 10V and this condition represents a simple surface treatment for Ti-7.5Mo alloy that has high potential for biomedical applications.

Sign in / Sign up

Export Citation Format

Share Document