scholarly journals The Efficacy of Polymer Coatings for the Protection of Electroless Copper Plated Polyester Fabric

Polymers ◽  
2020 ◽  
Vol 12 (6) ◽  
pp. 1277 ◽  
Author(s):  
Alenka Ojstršek ◽  
Natalija Virant ◽  
Daryl Fox ◽  
Latha Krishnan ◽  
Andrew Cobley
Keyword(s):  
Screen Printing ◽  
Base Material ◽  
Polyester Fabric ◽  
Polymer Coatings ◽  
Mechanical Characterisation ◽  
Polyurethane Resin ◽  
Colour Changes ◽  
Acrylate Resin ◽  
Photo Stability

The selective metallisation of textiles is becoming a very important process in the development of electronic or e-textiles. This study investigated the efficacy of polymer coatings for the protection of copper (Cu) conductive tracks electroless plated on polyester (PES) fabric against laundering and rubbing, without essentially affecting the physical-mechanical and optical properties of the base material. After the electroless deposition of a consistent layer of Cu onto PES, four polymers were applied individually by screen-printing or padding. The physical-mechanical characterisation of coated textiles revealed that polyurethane resin (PUR) and modified acrylate resin (AR) had little effect on the air permeability, tensile strength and breaking tenacity of the PES, as compared to silicone elastomer polydimethylsiloxane (PDMS) and epoxy resin (ER). On the other hand, PUR and PDMS had higher abrasion resistance and photo-stability under prolonged UV irradiation, as compared to AR and ER. In addition, freshly Cu plated samples were coated with polymers, washed up to 30 cycles and characterised by measuring their electrical resistivity, determination of colour changes and the examination of the surface morphology. Based on these results, PUR presented the most suitable protection of Cu tracks on PES, with the lowest impact on physical-mechanical properties. ER is not recommended to be used for protection of Cu tracks on fabrics, due to its rigidity, low photo-stability, washing and wear durability.

Determination of a Rubber-Like Material Model as an Inverse Problem

2011 ◽  
Vol 70 ◽  
pp. 225-230 ◽  
Author(s):  
Agnieszka Derewonko ◽  
Andrzej Kiczko
Keyword(s):  
Selection Process ◽  
Axial Stress ◽  
Constitutive Models ◽  
Material Model ◽  
Polyester Fabric ◽  
Point Of View ◽  
Air Cushion ◽  
Ill Conditioning ◽  
Stress States

The purpose of this paper is to describe the selection process of a rubber-like material model useful for simulation behaviour of an inflatable air cushion under multi-axial stress states. The air cushion is a part of a single segment of a pontoon bridge. The air cushion is constructed of a polyester fabric reinforced membrane such as Hypalon®. From a numerical point of view such a composite type poses a challenge since numerical ill-conditioning can occur due to stiffness differences between rubber and fabric. Due to the analysis of the large deformation dynamic response of the structure, the LS-Dyna code is used. Since LS-Dyna contains more than two-hundred constitutive models the inverse method is used to determine parameters characterizing the material on the base of results of the experimental test.

Mechanical Behaviour of CoCrMo Alloy with Si Content

2015 ◽  
Vol 754-755 ◽  
pp. 1017-1022 ◽  
Author(s):  
Petrică Vizureanu ◽  
Mirabela Georgiana Minciună ◽  
Dragoş Cristian Achiţei ◽  
Andrei Victor Sandu ◽  
Kamarudin Hussin
Keyword(s):  
Tensile Strength ◽  
Chemical Composition ◽  
Testing Machine ◽  
Base Material ◽  
Optical Emission ◽  
Experimental Tests ◽  
Optical Emission Spectrometry ◽  
Emission Spectrometry ◽  
Standard Samples

.The paper present aspects about the obtaining of non-precious dental alloys (type CoCrMo and CoCrMoSi7), the determination of chemical composition by optical emission spectrometry and the experimental tests for determining the tensile strength, made on standard plate samples. The base material used in experiments was a commercial alloy, from CoCrMo system, which belongs to the class of dental non-precious alloys, intended to medical applications. The obtaining of studied alloy was made on arc re-melting installation, under vacuum, type MRF ABJ 900. The process followed to realize a rapid melting, with a maximum admissible current intensity. The samples for tests were obtained by casting in an electric arc furnace, under vacuum, in optimal conditions for melting and solidification and processing by electro-erosion, to eliminate all the disturbing factors which come by processing conditions for the samples. The determination of chemical composition for cobalt based alloys, by optical emission spectrometry, was made on SpectromaxX equipment with spark. The electrical discharge is made with the elimination of an energy quantity, fact which determine plasma forming and light issue. Tensile tests for standard samples, made from cobalt based alloy, was made on Instron 3382 testing machine, and assisted by computer. The obtained results are: elongation, elasticity modulus, tensile strength and offer complete information about the analyzed mechanical properties. For the certitude of obtained experimental results, the tests were made on samples with specific dimensions according ISO 6892-1:2009(E) standard, both for the tensile strength, and also machine operation.

scholarly journals Features of the Surface and Subsurface Waves Application for Ultrasonic Evaluation of Physicomechanical Properties of Solids. Part 1. Influence of the Geometrical Parameters

2018 ◽  
Vol 9 (4) ◽  
pp. 325-326
Author(s):  
A. R. Baev ◽  
A. L. Mayorov ◽  
M. V. Asadchaya ◽  
V. N. Levkovich ◽  
K. G. Zhavoronkov
Keyword(s):  
Protective Coating ◽  
Layer Structure ◽  
Base Material ◽  
Protective Layer ◽  
Body Waves ◽  
Measuring System ◽  
Geometrical Parameters ◽  
Small Aperture ◽  
Ultrasonic Evaluation

Application of surface and subsurface waves for control of objects with a double-layer structure allows to extend possibilities of diagnostics of their physico-mechanical properties. The purpose of work was to determine conditions and offer recommendations providing measuring of ultrasonic velocity and amplitude of the former modes in protective layers and in basis of object at one-sided access to its surface.The analysis of an acoustic path of a measuring system in relation to ultrasonic evaluation of the objects having the restricted sizes and the protective coating according to velocity data of the surface and subsurface waves propagation is made. On the basis of representations of beam acoustics the dependences connecting a wavelength of the excited surface and subsurface modes, thickness and width of a controlled object, acoustic base of a sounding are defined. There are to provide a condition leveling of the influence of an acoustical noise created by the reflected and accompanying waves on parameters of acoustic signal with the given quantity of oscillations in an impulse.The principle opportunity is shown and conditions for determination of velocity of subsurface body waves in the base material which is under a protective coating layer are established. For these purposes on the basis of use of the block of ultrasonic probes the optimum scheme of a sounding is offered and the analytical expression for calculation of required velocity considering varying of thickness of a covering is received.The method of acoustical measuring realized by a direct and reverse sounding of the objects with small aperture and angle probes was analysed and formulas for determination of speed of subsurface wave under protective layer of the wedge form have been got. An ultrasonic device is suggested for the excitationreception of subsurface waves with different speed in objects (on 20–35 %) using for the acoustic concordance of environments of metallic sound duct as a wedge. Possibility of leveling of interference in a protective layer to control efects in basis of material by a volume wave by creation of supporting echo-signal of longitudinal wave of the set frequency and entered normally to the surface of object was studied.

scholarly journals CONSIDERATION ABOUT DEFORMABILITY OF BIMETAL BRAZING JOINTS

2017 ◽  
Vol 18 (2) ◽  
Author(s):  
IONEL OLARU ◽  
AURELIAN ALBUŢ ◽  
VLAD CIUBOTARIU
Keyword(s):  
Base Material ◽  
Materials Used

Brazing is realized by joining the added material to the base material thus it is realised a solid joint between materials. The degree of dissolution of materials used in assembly is very important in realization of sustainable bimetallic joints that can be stamped successfully. The stamping creates areas where joints can give the size and material compression degrees because its variation. A better stamping of these bimetallic brazed plates can be obtained through the exactly determination of these material areas.

scholarly journals Simultaneous Determination and Stability Studies on Diminazene Diaceturate and Phenazone Using Developed Derivative Spectrophotometric Method

2017 ◽  
Vol 2017 ◽  
pp. 1-6 ◽  
Author(s):  
Ruaa Mohamed Akode ◽  
Shaza Wagiealla Shantier ◽  
Elrasheed Ahmed Gadkariem ◽  
Magdi Awadalla Mohamed
Keyword(s):  
Simultaneous Determination ◽  
Correlation Coefficients ◽  
Degradation Process ◽  
Stability Studies ◽  
Temperature Dependent ◽  
First Order Kinetics ◽  
First Derivative Spectrophotometry ◽  
Aqueous Mixture ◽  
Photo Stability

This work presents UV first derivative spectrophotometry as a precise, accurate, and feasible method for simultaneous determination of diminazene diaceturate and phenazone in bulk and dosage forms. The absorbance values of diminazene diaceturate and phenazone aqueous mixture were obtained at 398 nm and 273 nm, respectively. The developed method was proved to be linear over the concentration ranges (2–10) μg/mL and (2.496–12.48) μg/mL for diminazene diaceturate and phenazone, respectively, with good correlation coefficients (not less than 0.997). The detection and quantitation limits were found to be (LOD = 0.63 and 0.48 μg/mL; LOQ = 1.92 and 1.47 μg/mL, resp.). The developed method was employed for stability studies of both drugs under different stress conditions. Diminazene diaceturate was prone to degrade at acidic pH via first-order kinetics. The degradation process was found to be temperature dependent with an activation energy of 7.48 kcal/mole. Photo-stability was also investigated for this drug.

RP-HPLC AND HPTLC STABILITY INDICATING ASSAY METHODS FOR IVERMECTIN IN BULK AND TABLET DOSAGE FORM

INDIAN DRUGS ◽  
2018 ◽  
Vol 55 (03) ◽  
pp. 32-42
Author(s):  
G. P Wani ◽  
◽  
S. B Jadhav
Keyword(s):  
Mobile Phase ◽  
Stress Testing ◽  
Hplc Method ◽  
Rp Hplc ◽  
Assay Methods ◽  
Photo Stability ◽  
Tablet Dosage ◽  
Hptlc Method ◽  
Alkaline Oxidation

Simple, rapid, precise, accurate RP-HPLC and HPTLC methods have been developed and validated for ivermectin in bulk and its marketed formulation. RP-HPLC method for drug was achieved on Grace C18 (250 mm X 4.6 ID, Particle size; 5 μ) column using mobile phase acetonitrile: 10 mM phosphate buffer (95:05 v/v) pH adjusted to 3 with o-phosphoric acid. Detection of drug was done at 245 nm. The retention time was found to be 5.83 min. HPTLC method for ivermectin was accomplished on a precoated silica gel aluminium plate 60F-254 (CAMAG Linomat 5), using toluene: methanol: glacial acetic acid (8:2:0.1 v/v/v) as a mobile phase. The densitometric scanning was performed at 245 nm which showed Rf 0.46 for ivermectin. The stress testing of the drug individually was carried out under acidic, alkaline, oxidation, photo-stability and thermal degradation conditions. The proposed methods were successfully applied for the determination of drug in bulk and its marketed formulation.

scholarly journals The Influence of 30 Years Outdoor Weathering on the Durability of Hydrophobic Agents Applied on Obernkirchener Sandstones

Buildings ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 18 ◽  
Author(s):  
Jeanette Orlowsky ◽  
Franziska Braun ◽  
Melanie Groh
Keyword(s):  
Water Absorption ◽  
Water Uptake ◽  
Capillary Water ◽  
Capillary Water Absorption ◽  
Absorption Determination ◽  
Colour Changes ◽  
Uptake Velocity ◽  
Outdoor Weathering

The durability of eleven different water repellents applied on one sandstone type was studied after a long-term weathering at seven different locations in Germany. By measuring colour changes, it could be shown that the formation of black crusts, the deposition of particles and biogenic growth caused a gradual darkening as well as significant changes in total colour over time. Additionally, the water absorption behaviour was investigated with two different methods: applying a low pressure using the pipe method and capillary water absorption measurements from a wet underlay. Afterwards, the test results were analysed with four different evaluation methods: calculation of the protection degree from pipe method and capillary water absorption, determination of the velocity of water uptake during capillary water absorption and calculation of the damaged depth of the stone surface using single-sided NMR technique. The growing damaged depth leads to an increase of the water uptake velocity and to a decrease of the protection degree of the applied hydrophobing agents. Three protective agents based on isobutyltrimethoxysilane showed already after two years of outdoor weathering a clear loss of performance, which significantly increased after 30 years of exposure.

Calculation and Experimental Technique for Determining the Damping Properties of Composite Materials

2018 ◽  
Vol 938 ◽  
pp. 46-53 ◽  
Author(s):  
Sergey I. Koryagin ◽  
O.V. Sharkov ◽  
Nikolay L. Velikanov
Keyword(s):  
Experimental Technique ◽  
Polymer Coatings ◽  
Engineering Systems ◽  
Damping Properties ◽  
Metal Structures ◽  
Experimental Specimen ◽  
Adhesive Compositions ◽  
Improved Accuracy ◽  
Damping Capability

Polymer coatings are widely used for effective vibration damping of sheet or hull structures of different engineering systems. The article presents a calculation and experimental technique that enables improved accuracy and validity of damping properties determination of polymer coatings. Mathematical models to determine the parameters of the experimental specimen having a homogenous strain state of the polymer coating are obtained. Experimentally confirmed that the use of coatings based on adhesive compositions such as "Sprut" increases by 18...28 times the damping capability in metal structures. An addition of fillers in adhesive compositions "Sprut" type in a proportion of 30...50% of its weight reduces by 2.4 times the damping properties of metal structures.

Sign in / Sign up

Export Citation Format

Share Document