scholarly journals Reclaimed Rubber/Poly(ε-caprolactone) Blends: Structure, Mechanical, and Thermal Properties

Polymers ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 1204 ◽  
Author(s):  
Aleksander Hejna ◽  
Łukasz Zedler ◽  
Marta Przybysz-Romatowska ◽  
Javier Cañavate ◽  
Xavier Colom ◽  
...  
Keyword(s):  
Global Scale ◽  
Waste Materials ◽  
Mechanical And Thermal Properties ◽  
Ftir Analysis ◽  
Structure And Properties ◽  
Scanning Calorimetry ◽  
Good Thermal Stability ◽  
Waste Rubber ◽  
Interfacial Compatibility ◽  
Dynamic Mechanical Testing

The amount of elastomeric waste, especially from tires is constantly increasing on a global scale. The recycling of these residua should be considered a priority. Compounding the waste rubbers with other polymers can be an excellent alternative to reuse waste materials. This procedure requires solving the issue of the lack of compatibility between the waste rubber particles and other polymers. Simultaneously, there is a claim for introducing biodegradable plastics materials to reduce their environmental impact. In this work, reclaimed rubber/poly(ε-caprolactone) (RR/PCL) blends are proposed to enhance the recycling and upcycling possibilities of waste rubbers. The results show that the addition of PCL to the RR allows obtaining blends with improved mechanical properties, good thermal stability, and enhanced interfacial compatibility between the used components. Structure and properties of the proposed RR/PCL have been studied by means of static and dynamic mechanical testing, Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA)-FTIR analysis.

A study on the fracture, mechanical and thermal properties of chain extended recycled poly(ethylene terephthalate)

2015 ◽  
Vol 30 (8) ◽  
pp. 1157-1172 ◽  
Author(s):  
Nevin Gamze Karsli
Keyword(s):  
Thermal Properties ◽  
Ethylene Terephthalate ◽  
Chain Extender ◽  
Mechanical And Thermal Properties ◽  
Ftir Analysis ◽  
Dsc Analysis ◽  
Scanning Calorimetry ◽  
Poly Ethylene Terephthalate ◽  
Impact Modifier ◽  
Poly Ethylene

The aim of this study is to simultaneously improve the mechanical strength and fracture toughness properties of recycled poly(ethylene terephthalate) (r-PET). For this purpose, Joncryl® was used as chain extender and Lotader® was used as impact modifier. The combined effect of chain extender and impact modifier on the chemical, fractural, mechanical, and thermal properties of r-PET was investigated. Fourier transformed infrared spectroscopy (FTIR) analysis, EWF analysis, tensile test, and differential scanning calorimetry (DSC) analysis were performed. FTIR analysis revealed that all the epoxy groups in the Joncryl® were consumed during the compounding. EWF results showed that while toughness of r-PET decreased with the addition of Joncryl®, toughness was increased with addition of impact modifier Lotader®. It was found that 2.5% Lotader® usage at the same time with Joncryl® increased the tensile strength of r-PET as well as toughness. It was observed from DSC analysis that chain extender and impact modifier addition did not change the thermal transition temperatures of r-PET.

Mechanical and thermal characterization of grafted PP-NCC nanocomposites

2019 ◽  
pp. 089270571987822
Author(s):  
Saud Aldajah ◽  
Mohammad Y Al-Haik ◽  
Waseem Siddique ◽  
Mohammad M Kabir ◽  
Yousef Haik
Keyword(s):  
Thermal Properties ◽  
Interfacial Adhesion ◽  
Thermal Characterization ◽  
Mechanical And Thermal Properties ◽  
Screw Extruder ◽  
Scanning Calorimetry ◽  
Three Point Bending ◽  
Twin Screw ◽  
Thermal Stability Of

This study reveals the enhancement of mechanical and thermal properties of maleic anhydride-grafted polypropylene (PP- g-MA) with the addition of nanocrystalline cellulose (NCC). A nanocomposite was manufactured by blending various percentages of PP, MA, and NCC nanoparticles by means of a twin-screw extruder. The influence of varying the percentages of NCC on the mechanical and thermal behavior of the nanocomposite was studied by performing three-point bending, nanoindentation, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and Fourier-transform infrared (FTIR) spectroscopy tests. The novelty of this study stems on the NCC nanoparticles and their ability to enhance the mechanical and thermal properties of PP. Three-point bending and nanoindentation tests revealed improvement in the mechanical properties in terms of strength, modulus, and hardness of the PP- g-MA nanocomposites as the addition of NCC increased. SEM showed homogeneity between the mixtures which proved the presence of interfacial adhesion between the PP- g-MA incorporated with NCC nanoparticles that was confirmed by the FTIR results. DSC and TGA measurements showed that the thermal stability of the nanocomposites was not compromised due to the addition of the coupling agent and reinforced nanoparticles.

scholarly journals Effect of Nanofiller Content on Dynamic Mechanical and Thermal Properties of Multi-Walled Carbon Nanotube and Montmorillonite Nanoclay Filler Hybrid Shape Memory Epoxy Composites

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 700
Author(s):  
Muhamad Hasfanizam Mat Yazik ◽  
Mohamed Thariq Hameed Sultan ◽  
Mohammad Jawaid ◽  
Abd Rahim Abu Talib ◽  
Norkhairunnisa Mazlan ◽  
...  
Keyword(s):  
Shape Memory ◽  
High Performance ◽  
Loss Modulus ◽  
Decomposition Temperature ◽  
Hybrid Nanocomposites ◽  
Mechanical And Thermal Properties ◽  
Scanning Calorimetry ◽  
Hybrid Filler ◽  
Dynamic Mechanical ◽  
Tan Δ

The aim of the present study has been to evaluate the effect of hybridization of montmorillonite (MMT) and multi-walled carbon nanotubes (MWCNT) on the thermal and viscoelastic properties of shape memory epoxy polymer (SMEP) nanocomposites. In this study, ultra-sonication was utilized to disperse 1%, 3%, and 5% MMT in combination with 0.5%, 1%, and 1.5% MWCNT into the epoxy system. The fabricated SMEP hybrid nanocomposites were characterized via differential scanning calorimetry, dynamic mechanical analysis, and thermogravimetric analysis. The storage modulus (E’), loss modulus (E”), tan δ, decomposition temperature, and decomposition rate, varied upon the addition of the fillers. Tan δ indicated a reduction of glass transition temperature (Tg) for all the hybrid SMEP nanocomposites. 3% MMT/1% MWCNT displayed best overall performance compared to other hybrid filler concentrations and indicated a better mechanical property compared to neat SMEP. These findings open a way to develop novel high-performance composites for various potential applications, such as morphing structures and actuators, as well as biomedical devices.

scholarly journals Recycling Waste Cotton Cloths for the Isolation of Cellulose Nanocrystals: A Sustainable Approach

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 626
Author(s):  
Siti Hajar Mohamed ◽  
Md. Sohrab Hossain ◽  
Mohamad Haafiz Mohamad Kassim ◽  
Mardiana Idayu Ahmad ◽  
Fatehah Mohd Omar ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Cellulose Nanocrystals ◽  
Value Added ◽  
Crystallinity Index ◽  
Attenuated Total Reflection ◽  
Cellulose Content ◽  
Scanning Calorimetry ◽  
Good Thermal Stability ◽  
Alkaline Pulping ◽  
Hydrolysis Of Cellulose

There is an interest in the sustainable utilization of waste cotton cloths because of their enormous volume of generation and high cellulose content. Waste cotton cloths generated are disposed of in a landfill, which causes environmental pollution and leads to the waste of useful resources. In the present study, cellulose nanocrystals (CNCs) were isolated from waste cotton cloths collected from a landfill. The waste cotton cloths collected from the landfill were sterilized and cleaned using supercritical CO2 (scCO2) technology. The cellulose was extracted from scCO2-treated waste cotton cloths using alkaline pulping and bleaching processes. Subsequently, the CNCs were isolated using the H2SO4 hydrolysis of cellulose. The isolated CNCs were analyzed to determine the morphological, chemical, thermal, and physical properties with various analytical methods, including attenuated total reflection-Fourier transform-infrared spectroscopy (ATR-FTIR), field-emission scanning electron microscopy (FE-SEM), energy-filtered transmission electron microscopy (EF-TEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The results showed that the isolated CNCs had a needle-like structure with a length and diameter of 10–30 and 2–6 nm, respectively, and an aspect ratio of 5–15, respectively. Additionally, the isolated CNCs had a high crystallinity index with a good thermal stability. The findings of the present study revealed the potential of recycling waste cotton cloths to produce a value-added product.

scholarly journals Chemistry of collagen cross-links: glucose-mediated covalent cross-linking of type-IV collagen in lens capsules

1993 ◽  
Vol 296 (2) ◽  
pp. 489-496 ◽  
Author(s):  
A J Bailey ◽  
T J Sims ◽  
N C Avery ◽  
C A Miles
Keyword(s):  
Type Iv Collagen ◽  
Cross Linking ◽  
Mechanical And Thermal Properties ◽  
Maximum Strain ◽  
Scanning Calorimetry ◽  
Melting Temperatures ◽  
Type Iv ◽  
Collagen Molecules ◽  
Cross Links

The incubation of lens capsules with glucose in vitro resulted in changes in the mechanical and thermal properties of type-IV collagen consistent with increased cross-linking. Differential scanning calorimetry (d.s.c.) of fresh lens capsules showed two major peaks at melting temperatures Tm 1 and Tm 2 at approx. 54 degrees C and 90 degrees C, which can be attributed to the denaturation of the triple helix and 7S domains respectively. Glycosylation of lens capsules in vitro for 24 weeks caused an increase in Tm 1 from 54 degrees C to 61 degrees C, while non-glycosylated, control incubated capsules increased to a Tm 1 of 57 degrees C. The higher temperature required to denature the type-IV collagen after incubation in vitro suggested increased intermolecular cross-linking. Glycosylated lens capsules were more brittle than fresh samples, breaking at a maximum strain of 36.8 +/- 1.8% compared with 75.6 +/- 6.3% for the fresh samples. The stress at maximum strain (or ‘strength’) was dramatically reduced from 12.0 to 4.7 N.mm.mg-1 after glycosylation in vitro. The increased constraints within the system leading to loss of strength and increased brittleness suggested not only the presence of more cross-links but a difference in the location of these cross-links compared with the natural lysyl-aldehyde-derived cross-links. The chemical nature of the fluorescent glucose-derived cross-link following glycosylation was determined as pentosidine, at a concentration of 1 pentosidine molecule per 600 collagen molecules after 24 weeks incubation. Pentosidine was also determined in the lens capsules obtained from uncontrolled diabetics at a level of about 1 per 100 collagen molecules. The concentration of these pentosidine cross-links is far too small to account for the observed changes in the thermal and mechanical properties following incubation in vitro, clearly indicating that another as yet undefined, but apparently more important cross-linking mechanism mediated by glucose is taking place.

Effects of Steam Heat and Dry Heat Sterilization on Thermal and Mechanical Properties of Nylon and Policarbonate in Fabrication with Fused Filament

2021 ◽  
Vol 891 ◽  
pp. 150-163
Author(s):  
Jorge Mauricio Fuentes ◽  
Omar Flor Unda ◽  
Santiago Ferrandiz ◽  
Franyelit Suarez
Keyword(s):  
Mechanical Properties ◽  
Thermomechanical Analysis ◽  
Mechanical Tests ◽  
Effect Of Temperature ◽  
Mechanical And Thermal Properties ◽  
Scanning Calorimetry ◽  
Thermal Tests ◽  
Dry Heat ◽  
Izod Impact ◽  
Steam Heat

In this article presents evidence about performance of mechanical properties of polycarbonate and nylon materials, which are used in the additive manufacturing by deposition of molten material and that have been subjected to sterilization processes by moist heat at 121°C and dry heat at 140°C. This study provides useful information to consider the use of these materials in sanitary and sterile settings. Mechanical tests of tensile, flex, hardness, Izod impact, thermal tests in Differential Scanning Calorimetry DSC, Thermomechanical analysis TMA and Scanning Electron Microscopy SEM were performed. It is concluded that the mechanical and thermal properties have not been altered through the effect of temperature in sterilization processes.

Decellularized liver-regenerative 3D printing biomaterials for cell-based liver therapies via a designed procedure combined with papain-containing reagent treatments and supercritical fluids

2021 ◽  
pp. 1-8
Author(s):  
Ching-Cheng Huang
Keyword(s):  
3D Printing ◽  
Thermo Gravimetric Analysis ◽  
Extraction Process ◽  
Gravimetric Analysis ◽  
Collagen Scaffolds ◽  
Scanning Calorimetry ◽  
Porcine Liver ◽  
Good Thermal Stability ◽  
Decellularized Liver ◽  
Liver Collagen

BACKGROUND: The biologic scaffolds derived from decellularized tissues and organs have been successfully developed in a variety of preclinical and/or clinical studies. OBJECTIVE: The new decellularized liver-regenerative 3D printing biomaterials were designed and prepared for cell-based liver therapies. METHODS: An extraction process was employed to remove the tissue and cellular molecules from porcine liver via pretreatment of supercritical fluid of carbon dioxide (ScCO2). Varying porosities of the decellularized liver tissues were created using papain-containing reagent treatments after ScCO2. RESULTS: The resulting liver-regenerative 3D printing biomaterials of decellularized liver collagen scaffolds were characterized by Fourier transform infrared spectroscopy, thermo-gravimetric analysis, differential scanning calorimetry and scanning electron microscopy. CONCLUSIONS: The decellularized liver collagen scaffolds with good thermal stability (>150 °C) were obtained and employed as liver-regenerative 3D printing biomaterials for cell-based liver therapies.

Mechanical and Thermal Properties of Magnesia Binder Based on Natural and Technogenic Raw Materials

2021 ◽  
Vol 320 ◽  
pp. 181-185
Author(s):  
Elvija Namsone ◽  
Genadijs Sahmenko ◽  
Irina Shvetsova ◽  
Aleksandrs Korjakins
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Raw Materials ◽  
High Strength ◽  
Strength Properties ◽  
Waste Materials ◽  
Mechanical And Thermal Properties ◽  
Experimental Part ◽  
Technogenic Raw Materials ◽  
Caustic Magnesia

Because of low calcination temperature, magnesia binders are attributed as low-CO2 emission materials that can benefit the environment by reducing the energy consumption of building sector. Portland cement in different areas of construction can be replaced by magnesia binder which do not require autoclave treatment for hardening, it has low thermal conductivity and high strength properties. Magnesium-based materials are characterized by decorativeness and ecological compatibility.The experimental part of this research is based on the preparation of magnesia binders by adding raw materials and calcinated products and caustic magnesia. The aim of this study was to obtain low-CO2 emission and eco-friendly material using local dolomite waste materials, comparing physical, mechanical, thermal properties of magnesium binders.

The influence of adding long basalt fiber on the mechanical and thermal properties of composites based on poly(oxymethylene)

2018 ◽  
Vol 33 (4) ◽  
pp. 435-450 ◽  
Author(s):  
Patrycja Bazan ◽  
Stanisław Kuciel ◽  
Mariola Sądej
Keyword(s):  
Mechanical Properties ◽  
Thermal Properties ◽  
Average Length ◽  
Flexural Modulus ◽  
Basalt Fiber ◽  
Charpy Impact ◽  
Mechanical And Thermal Properties ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Atr Spectroscopy

The work has evaluated the possibility of the potential reinforcing of poly(oxymethylene) (POM) by basalt fibers (BFs) and influence of BFs addition on thermal properties. Two types of composites were produced by injection molding. There were 20 and 40 wt% long BFs content with an average length of 1 mm. The samples were made without using a compatibilizer. In the experimental part, the basic mechanical properties (tensile strength, modulus of elasticity, strain at break, flexural modulus, flexural strength, and deflection at 3.5% strain) of composites based on POM were determined. Tensile properties were also evaluated at three temperatures −20°C, 20°C, and 80°C. The density and Charpy impact of the produced composites were also examined. The influence of water absorption on mechanical properties was investigated. Thermal properties were conducted by the differential scanning calorimetry, thermal gravimetric analysis, and fourier transform infrared (FTIR)-attenuation total reflection (ATR) spectroscopy analysis. In order to make reference to the effects of reinforcement and determine the structure characteristics, scanning electron microscopy images were taken. The addition of 20 and 40 wt% by weight of fibers increases the strength and the stiffness of such composites by more than 30–70% in the range scale of temperature. Manufactured composites show higher thermal and dimensional stability in relation to neat POM.

scholarly journals Processing of (Co)Poly(2-oxazoline)s by Electrospinning and Extrusion from Melt and the Postprocessing Properties of the (Co)Polymers

Polymers ◽  
2020 ◽  
Vol 12 (2) ◽  
pp. 295 ◽  
Author(s):  
Wojciech Wałach ◽  
Natalia Oleszko-Torbus ◽  
Alicja Utrata-Wesołek ◽  
Marcelina Bochenek ◽  
Ewa Kijeńska-Gawrońska ◽  
...  
Keyword(s):  
Differential Scanning Calorimetry ◽  
Thermal Properties ◽  
Molar Mass ◽  
Three Dimensional ◽  
Fused Deposition Modelling ◽  
Processing Conditions ◽  
Structure And Properties ◽  
Scanning Calorimetry ◽  
Gradient Copolymers ◽  
Fused Deposition

Poly(2-oxazoline) (POx) matrices in the form of non-woven fibrous mats and three-dimensional moulds were obtained by electrospinning and fused deposition modelling (FDM), respectively. To obtain these materials, poly(2-isopropyl-2-oxazoline) (PiPrOx) and gradient copolymers of 2-isopropyl- with 2-n-propyl-2-oxazoline (P(iPrOx-nPrOx)), with relatively low molar masses and low dispersity values, were processed. The conditions for the electrospinning of POx were optimised for both water and the organic solvent. Also, the FDM conditions for the fabrication of POx multi-layer moulds of cylindrical or cubical shape were optimised. The properties of the POx after electrospinning and extrusion from melt were determined. The molar mass of all (co)poly(2-oxazoline)s did not change after electrospinning. Also, FDM did not influence the molar masses of the (co)polymers; however, the long processing of the material caused degradation and an increase in molar mass dispersity. The thermal properties changed significantly after processing of POx what was monitored by increase in enthalpy of exo- and endothermic peaks in differential scanning calorimetry (DSC) curve. The influence of the processing conditions on the structure and properties of the final material were evaluated having in a mind their potential application as scaffolds.

Sign in / Sign up

Export Citation Format

Share Document