scholarly journals Effect of SrTiO3 Nanoparticles in Conductive Polymer on the Thermoelectric Performance for Efficient Thermoelectrics

Polymers ◽  
2020 ◽  
Vol 12 (4) ◽  
pp. 777 ◽  
Author(s):  
Dabin Park ◽  
Hyun Ju ◽  
Jooheon Kim
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Room Temperature ◽  
Conductive Polymer ◽  
Inorganic Materials ◽  
Thermoelectric Performance ◽  
One Pot ◽  
High Seebeck Coefficient ◽  
Solvothermal Methods ◽  
Pani Matrix

We present hybrid organic inorganic materials, namely, SrTiO3/polyaniline (PANI) composites, with high thermoelectric performance; samples with various SrTiO3 contents (10, 20, 30, and 50 wt.%) were prepared. The PANI component was obtained through the polymerization of aniline monomers, followed by camphosulfonic acid-doping to enhance its electrical conductivity. SrTiO3, with a high Seebeck coefficient, was used as the N-type inorganic componenet; it was synthesized via a one-pot solvothermal methods and, then, dispersed into the conductive PANI matrix. The SrTiO3 content influenced the Seebeck coefficient and electrical conductivity of the resulting composites. The variations in the thermoelectric properties of the SrTiO3/PANI composites consequently changed their power factor; at room temperature, the highest value was ~49.6 μW·m/K2, which is 17 times larger than that of pure PANI.

scholarly journals Effects of the Interface between Inorganic and Organic Components in a Bi2Te3–Polypyrrole Bulk Composite on Its Thermoelectric Performance

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3080
Author(s):  
Cham Kim ◽  
David Humberto Lopez
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Thermal Properties ◽  
Seebeck Coefficient ◽  
Power Factor ◽  
Energy Band ◽  
Phonon Scattering ◽  
Thermoelectric Performance ◽  
High Seebeck Coefficient ◽  
Fabrication Condition

We provided a method to hybridize Bi2Te3 with polypyrrole, thus forming an inorganic/organic bulk composite (Bi2Te3–polypyrrole), in which the effects of energy band junction and phonon scattering were expected to occur at the interface of the two components. Bi2Te3–polypyrrole exhibited a considerably high Seebeck coefficient compared to pristine Bi2Te3, and thus it recorded a somewhat increased power factor despite the loss in electrical conductivity caused by the organic component, polypyrrole. Bi2Te3–polypyrrole also exhibited much lower thermal conductivity than pristine Bi2Te3 because of the phonon scattering effect at the interface. We successfully brought about the decoupling phenomenon of electrical and thermal properties by devising an inorganic/organic composite and adjusting its fabrication condition, thereby optimizing its thermoelectric performance, which is considered the predominant property for n-type binary Bi2Te3 reported so far.

The Influence of Silicon Dopant and Processing on Thermoelectric Properties of B4C Ceramics

1998 ◽  
Vol 545 ◽  
Author(s):  
Ke-Feng Cai ◽  
Ce-Wen Nan ◽  
Xin-Min Min
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Hot Pressing ◽  
Figure Of Merit ◽  
Room Temperature ◽  
A Value ◽  
Si Doped

AbstractB4C ceramics doped with various content of Si (0 to 2.03 at%) are prepared via hot pressing. The composition and microstructure of the ceramics are characterized by means of XRD and EPMA. Their electrical conductivity and Seebeck coefficient of the samples are measured from room temperature up to 1500K. The electrical conductivity increases with temperature, and more rapidly after 1300K; the Seebeck coefficient of the ceramics also increases with temperature and rises to a value of about 320μVK−1. The value of the figure of merit of Si-doped B4C rises to about 4 × 10−4K−1 at 1500K.

Thermoelectric Properties of Semiconducting Intermetallic Compounds: FeGa3and RuGa3

2003 ◽  
Vol 793 ◽  
Author(s):  
Y. Amagai ◽  
A. Yamamoto ◽  
C. H. Lee ◽  
H. Takazawa ◽  
T. Noguchi ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
High Temperature ◽  
Seebeck Coefficient ◽  
Transport Properties ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Thermoelectric Figure Of Merit ◽  
Thermoelectric Figure ◽  
High Seebeck Coefficient

ABSTRACTWe report transport properties of polycrystalline TMGa3(TM = Fe and Ru) compounds in the temperature range 313K<T<973K. These compounds exhibit semiconductorlike behavior with relatively high Seebeck coefficient, electrical resistivity, and Hall carrier concentrations at room temperature in the range of 1017- 1018cm−3. Seebeck coefficient measurements reveal that FeGa3isn-type material, while the Seebeck coefficient of RuGa3changes signs rapidly from large positive values to large negative values around 450K. The thermal conductivity of these compounds is estimated to be 3.5Wm−1K−1at room temperature and decreased to 2.5Wm−1K−1for FeGa3and 2.0Wm−1K−1for RuGa3at high temperature. The resulting thermoelectric figure of merit,ZT, at 945K for RuGa3reaches 0.18.

Thermoelectric Performance of Glass Microsphere Dispersed Bi-Sb Composites at Low Temperature

2013 ◽  
Vol 743-744 ◽  
pp. 120-125
Author(s):  
Zhen Chen ◽  
Ye Mao Han ◽  
Min Zhou ◽  
Rong Jin Huang ◽  
Yuan Zhou ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Materials ◽  
Sem Analysis ◽  
Glass Microsphere ◽  
Thermoelectric Performance ◽  
X Ray Diffraction ◽  
X Ray ◽  
Measurement Results

In the present study, the glass microsphere dispersed Bi-Sb thermoelectric materials have been fabricated through mechanical alloying followed by pressureless sintering. The phase composition and the microstructure were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM) analysis. Electrical conductivity, Seebeck coefficient and thermal conductivity were measured in the temperature range of 77~300 K. The ZT values were calculated according to the measurement results. The results showed that the electrical conductivity, Seebeck coefficient and thermal conductivity decreased by adding glass microsphere into Bi-Sb thermoelectric materials. However, the optimum ZT value of 0.24 was obtained at 260 K, which was increased 10% than that of the Bi-Sb matrix. So it is confirmed that the thermoelectric performance of Bi-Sb-based materials can be improved by adding moderate glass microspheres.

Thermoelectric Properties of Binary-Phased Nanocomposites

2014 ◽  
Vol 809-810 ◽  
pp. 3-8
Author(s):  
Peng Xian Lu
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Hot Press ◽  
Point Temperature ◽  
Disordered Structure ◽  
Maximum Value ◽  
Hot Press Process

In order to increase the electrical conductivity greatly but maintain a large Seebeck coefficient and a low thermal conductivity simultaneously, the binary-phased LaCeFe3CoSb12-Sb nanocomposites composed of LaCeFe3CoSb12skutterudite nanospheres and semimetal Sb microsized ribbons were fabricated via a hydro/solvo thermal route. The results suggest that the Sb powders result in a disordered structure during a hot-press process at its melting-point temperature and the disordered structure has been partly preserved into the room-temperature materials successfully. The Sb microsized ribbons enhance the electrical conductivity of the binary-phased materials largely, meanwhile the disordered structure increases the Seebeck coefficient obviously even though the thermal conductivity is also increased slightly. Consequently, the figure of merit of the binary-phased materials is improved significantly and the maximum value of 1.54 at 773 K has been realized for the LaCeFe3CoSb15material.

Electrical Properties of AlN-SiC Ceramics

2006 ◽  
Vol 317-318 ◽  
pp. 641-644
Author(s):  
Ryota Kobayashi ◽  
Junichi Tatami ◽  
Toru Wakihara ◽  
Takeshi Meguro ◽  
Katsutoshi Komeya
Keyword(s):  
Electrical Conductivity ◽  
Electrical Properties ◽  
Seebeck Coefficient ◽  
Gas Flow ◽  
Room Temperature ◽  
Xrd Analysis ◽  
Sic Ceramics ◽  
Sic Ceramic ◽  
Powder Compacts ◽  
Electrical Conductors

AlN-SiC ceramics with 0 to 75 mol% of AlN were fabricated through pressureless sintering of very fine AlN and SiC. Powder compacts with different amounts of AlN were fired at 2000°C for 1 h in Argon gas flow using an induction-heating furnace. The microstructure and phases present in the products were evaluated using SEM and XRD. The AlN-SiC ceramics had a porous structure with 30% porosity, and the grain size was increased with the addition of AlN. XRD analysis showed that 2H was a main phase in all samples, though 3C and 6H phases were found in 25 mol%AlN-75 mol%SiC ceramic. The electrical properties of the AlN-SiC ceramics were evaluated at various temperatures ranging from room temperature to 300°C. The electrical conductivity of the AlN-SiC ceramics depended on the amount of AlN and on the temperature. The 75 mol%AlN-SiC ceramic had higher electrical resistance, though the other samples were electrical conductors. The highest electrical conductivity was obtained with the 25 mol% AlN composition, which was 7 S/m at room temperature and 30 S/m at 300°C. The Seebeck coefficient for the AlN-SiC ceramics increased with rising temperatures. The AlN-SiC ceramics with 50 mol%AlN had the highest Seebeck coefficient of 220 2V/K at 300°C.

scholarly journals Efficient interlayer charge release for high-performance layered thermoelectrics

2020 ◽  
Author(s):  
Hao Zhu ◽  
Zhou Li ◽  
Chenxi Zhao ◽  
Xingxing Li ◽  
Jinlong Yang ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Carrier Concentration ◽  
High Performance ◽  
Lattice Thermal Conductivity ◽  
Transport Barrier ◽  
High Seebeck Coefficient ◽  
Valence Bands ◽  
Increase Carrier Concentration

Abstract Many layered superlattice materials intrinsically possess large Seebeck coefficient and low lattice thermal conductivity, but poor electrical conductivity because of the interlayer transport barrier for charges, which has become a stumbling block for achieving high thermoelectric performance. Herein, taking BiCuSeO superlattice as an example, it is demonstrated that efficient interlayer charge release can increase carrier concentration, thereby activating multiple Fermi pockets through Bi/Cu dual vacancies and Pb codoping. Experimental results reveal that the extrinsic charges, which are introduced by Pb and initially trapped in the charge-reservoir [Bi2O2]2+ sublayers, are effectively released into [Cu2Se2]2− sublayers via the channels bridged by Bi/Cu dual vacancies. This efficient interlayer charge release endows dual-vacancy- and Pb-codoped BiCuSeO with increased carrier concentration and electrical conductivity. Moreover, with increasing carrier concentration, the Fermi level is pushed down, activating multiple converged valence bands, which helps to maintain a relatively high Seebeck coefficient and yield an enhanced power factor. As a result, a high ZT value of ∼1.4 is achieved at 823 K in codoped Bi0.90Pb0.06Cu0.96SeO, which is superior to that of pristine BiCuSeO and solely doped samples. The present findings provide prospective insights into the exploration of high-performance thermoelectric materials and the underlying transport physics.

A New Challenge of Polymer Thermoelectric Materials as Ecomaterials

2007 ◽  
Vol 539-543 ◽  
pp. 2329-2332 ◽  
Author(s):  
Yoshikazu Shinohara ◽  
Yoshio Imai ◽  
Yukihiro Isoda ◽  
Kentaro Hiraishi ◽  
Hachiro Nakanishi
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Oxidative Polymerization ◽  
Side Chain ◽  
Side Chains ◽  
Nmr Analysis ◽  
Alkyl Side Chains ◽  
High Seebeck Coefficient ◽  
Polymer Thermoelectric

Typical conductive polymers of poly(3-alkylthiophenes) were synthesized by oxidative polymerization. Polythiophene with no side chain was also electrolyticaly polymerized. Alkyl side chains were CnH2n+1 with n=4, 6, 8, 12. The regioregularity with the HT linkage was larger than 99% based on NMR analysis. We have evaluated the effect of side chain size on the thermoelectric properties of Seebeck coefficient and electrical conductivity. The results were as follows: 1) Seebeck coefficient decreased with an increasing electrical conductivity. 2) High Seebeck coefficient >1mV/K was observed at low electrical conductivity <10-2S/cm. 3) Small side chains, especially no side chain caused higher thermoelectric properties of polythiophene series.

Raising the Thermoelectric Performance of Fe3CoSb12 Skutterudites via Nd Filling and In-Situ Nanostructuring

2016 ◽  
Vol 16 (4) ◽  
pp. 3841-3847 ◽  
Author(s):  
Lijie Guo ◽  
Zhengwei Cai ◽  
Xiaolong Xu ◽  
Kunling Peng ◽  
Guiwen Wang ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Thermoelectric Performance ◽  
Large Reduction ◽  
Dimensionless Figure Of Merit ◽  
Plasma Sintering ◽  
Spark Plasma

p-type skutterudites NdxFe3CoSb12 with x equaling 0.8, 0.85, 0.9, 0.95, 1.0 have been synthesized by solid state reaction followed by spark plasma sintering. The influence of Nd filling on electrical and thermal transport properties has been investigated in the Nd-filled skutterudite compounds in the temperature range from room temperature to 800 K. It was found that the Seebeck coefficient is drastically enhanced via filling Nd in p-Type skutterudites as well as the corresponding power factor although electrical conductivity is reduced. In addition, a large reduction in thermal conductivity is achieved by Nd fillers through rattling effect along with the In-Situ nanostructured precipitate through scattering phonons with much wider frequency. These concomitant effects result in an enhanced thermoelectric performance with the dimensionless figure of merit ZT. These observations demonstrate an exciting scientific opportunity to raise the figure-of-merit of p-type skutterudites.

A thermoelectric copper-iodide composite from the pyrolysis of a well-defined coordination polymer

2018 ◽  
Vol 47 (16) ◽  
pp. 5564-5569 ◽  
Author(s):  
Shi-Qiang Bai ◽  
Ivy Hoi Ka Wong ◽  
Ming Lin ◽  
David James Young ◽  
T. S. Andy Hor
Keyword(s):  
Coordination Polymer ◽  
Seebeck Coefficient ◽  
Room Temperature ◽  
Carbon Composite ◽  
Copper Iodide ◽  
Molecular Material ◽  
Organic Hybrid ◽  
High Seebeck Coefficient

A robust and relatively light CuI-rich carbon composite derived from an inorganic–organic hybrid molecular material demonstrates a high Seebeck coefficient from room temperature to 204 °C.

Sign in / Sign up

Export Citation Format

Share Document