scholarly journals Modulating the Mechanical Properties of Electrospun PHB/PCL Materials by Using Different Types of Collectors and Heat Sealing

Polymers ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 693 ◽  
Author(s):  
Irena Borisova ◽  
Olya Stoilova ◽  
Nevena Manolova ◽  
Iliya Rashkov
Keyword(s):  
Mechanical Properties ◽  
Mechanical Tests ◽  
Fibrous Materials ◽  
Scanning Calorimetry ◽  
Before And After ◽  
Ft Ir ◽  
Improved Performance ◽  
Tunable Mechanical Properties ◽  
Cutting Direction ◽  
Ft Ir Spectroscopy

Two-component fibrous materials based on poly(3-hydroxybutyrate) (PHB, Tm = 160 °C) and poly(ε-caprolactone) (PCL, Tm = 60 °C) were successfully fabricated by dual-jet electrospinning of their separate spinning solutions. The desired alignment of the fibers that compose PHB/PCL mats was achieved by using three types of rotating collectors—drum (smooth), blade and grid. Additional fiber alignment in the direction of collector rotation was achieved by rotating at 2200 rpm. Moreover, the selected concentration of PCL spinning solution resulted in fibers with spindle-like defects along their length. Thus, “segment” sealing of the PHB (high-melting) fibers by the molten PCL (low-melting) fibers/defects sites was achieved after heating the PHB/PCL mats above the melting temperature (Tm) of PCL. The surface morphology, thermal behavior and mechanical properties of the PHB/PCL mats before and after thermal treatment were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) spectroscopy, differential scanning calorimetry (DSC) and mechanical tests. The results indicated that regardless of the cutting direction of the specimens (0° or 90°), thermal treated PHB/PCL mats reveal enhanced mechanical properties. Therefore, this work provides an easily feasible route for the fabrication of electrospun PHB/PCL mats with tunable mechanical properties and improved performance.

scholarly journals Fast Preparation of High-Performance Wood Materials Assisted by Ultrasonic and Vacuum Impregnation

Forests ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 567
Author(s):  
Hong Yang ◽  
Mingyu Gao ◽  
Jinxin Wang ◽  
Hongbo Mu ◽  
Dawei Qi
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
Mechanical Tests ◽  
Vacuum Impregnation ◽  
Natural Forests ◽  
Ultrasonic Pretreatment ◽  
Fast Growing ◽  
Before And After ◽  
New Material ◽  
Ft Ir

In the absence of high-quality hardwood timber resources, we have gradually turned our attention from natural forests to planted fast-growing forests. However, fast-growing tree timber in general has defects such as low wood density, loose texture, and poor mechanical properties. Therefore, improving the performance of wood through efficient and rapid technological processes and increasing the utilization of inferior wood is a good way to extend the use of wood. Densification of wood increases the strength of low-density wood and extends the range of applications for wood and wood-derived products. In this paper, the effects of ultrasonic and vacuum pretreatment on the properties of high-performance wood were explored by combining sonication, vacuum impregnation, chemical softening, and thermomechanical treatments to densify the wood; then, the changes in the chemical composition, microstructure, and mechanical properties of poplar wood before and after treatment were analyzed comparatively by FT-IR, XRD, SEM, and mechanical tests. The results showed that with ultrasonic pretreatment and vacuum impregnation, the compression ratio of high-performance wood reached its highest level and the MOR and MOE reached their maximums. With the help of this method, fast-growing softwoods can be easily prepared into dense wood materials, and it is hoped that this new material can be applied in the fields of construction, aviation, and automobile manufacturing.

Effects of Steam Heat and Dry Heat Sterilization on Thermal and Mechanical Properties of Nylon and Policarbonate in Fabrication with Fused Filament

2021 ◽  
Vol 891 ◽  
pp. 150-163
Author(s):  
Jorge Mauricio Fuentes ◽  
Omar Flor Unda ◽  
Santiago Ferrandiz ◽  
Franyelit Suarez
Keyword(s):  
Mechanical Properties ◽  
Thermomechanical Analysis ◽  
Mechanical Tests ◽  
Effect Of Temperature ◽  
Mechanical And Thermal Properties ◽  
Scanning Calorimetry ◽  
Thermal Tests ◽  
Dry Heat ◽  
Izod Impact ◽  
Steam Heat

In this article presents evidence about performance of mechanical properties of polycarbonate and nylon materials, which are used in the additive manufacturing by deposition of molten material and that have been subjected to sterilization processes by moist heat at 121°C and dry heat at 140°C. This study provides useful information to consider the use of these materials in sanitary and sterile settings. Mechanical tests of tensile, flex, hardness, Izod impact, thermal tests in Differential Scanning Calorimetry DSC, Thermomechanical analysis TMA and Scanning Electron Microscopy SEM were performed. It is concluded that the mechanical and thermal properties have not been altered through the effect of temperature in sterilization processes.

scholarly journals Tension mechanical properties of recycled glass-epoxy composite material

2012 ◽  
pp. 189-198 ◽  
Author(s):  
Jelena Petrovic ◽  
Darko Ljubic ◽  
Marina Stamenovic ◽  
Ivana Dimic ◽  
Slavisa Putic
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Material ◽  
Composite Materials ◽  
Modulus Of Elasticity ◽  
Epoxy Composite ◽  
Raw Materials ◽  
Mechanical Tests ◽  
Recycled Glass ◽  
Before And After

The significance of composite materials and their applications are mainly due to their good properties. This imposes the need for their recycling, thus extending their lifetime. Once used composite material will be disposed as a waste at the end of it service life. After recycling, this kind of waste can be used as raw materials for the production of same material, which raises their applicability. This indicates a great importance of recycling as a method of the renowal of composite materials. This study represents a contribution to the field of mechanical properties of the recycled composite materials. The tension mechanical properties (tensile strength and modulus of elasticity) of once used and disposed glass-epoxy composite material were compared before and after the recycling. The obtained results from mechanical tests confirmed that the applied recycling method was suitable for glass-epoxy composite materials. In respect to the tensile strength and modulus of elasticity it can be further assessed the possibility of use of recycled glass-epoxy composite materials.

GROWTH AND STUDIES OF PROPERTIES OF COPPER SUCCINATE DIHYDRATE SINGLE CRYSTALS

2013 ◽  
Vol 27 (11) ◽  
pp. 1350073
Author(s):  
M. P. BINITHA ◽  
P. P. PRADYUMNAN
Keyword(s):  
Differential Scanning Calorimetry ◽  
Dielectric Constant ◽  
Single Crystals ◽  
Scanning Calorimetry ◽  
Force Microscopy ◽  
Atomic Force ◽  
Different Temperatures ◽  
Triclinic Structure ◽  
Ft Ir ◽  
Ft Ir Spectroscopy

Single crystals of copper succinate dihydrate (CSD) with triclinic structure were grown in silica gel medium. The functional groups in the crystal were analyzed by FT-IR Spectroscopy. Atomic Force Microscopy (AFM) revealed the striations on the surface of grown crystals, which were incorporated during its time of growth. Thermal degradation studies have been carried out by Differential Scanning Calorimetry (DSC). Dielectric constant and AC conductivity have been estimated as a function of frequency at different temperatures.

Preparation of epoxy/urethane graft interpenetrating polymer networks and study of mechanical, thermal and morphological properties

e-Polymers ◽  
2009 ◽  
Vol 9 (1) ◽  
Author(s):  
Mehdi Ghafghazi ◽  
Masoud Esfandeh ◽  
Jalil Morshedian
Keyword(s):  
Mechanical Properties ◽  
Polymer Networks ◽  
Weight Ratio ◽  
Interpenetrating Polymer Networks ◽  
Morphological Properties ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Molecular Weights ◽  
Degradation Temperature ◽  
Ft Ir

AbstractThis paper describes the preparation of Epoxy/Urethane (EP/PU) graft interpenetrating polymer networks (g-IPNs) and investigates the effect of EP/PU weight ratio and urethane's prepolymer molecular weight on the mechanical, morphological and thermal properties of the IPN system. Here, g-IPN was prepared by thorough mixing of an isocyanate-terminated urethane prepolymer with an epoxy resin followed by simultaneous curing of the resins. Polytetra hydrofuranate (PTHF), molecular weights (Mw) 1000, 2000 and 3000 g/gmol, was used to prepare urethane prepolymers. EP/PU weight ratios were 75/25, 50/50, 30/70 and 15/85. Disappearance of epoxide and isocyanate functional groups was followed by Fourier Transform Infrared spectroscopy (FT-IR), showing curing of the resins. Differential Scanning Calorimetry (DSC) was used to investigate the glass transition temperature (Tg) of the IPNs. Thermal Gravimetric Analysis (TGA), Dynamic Mechanical Thermal Analysis (DMTA), tensile measurements and Scanning Electron Microscopy (SEM) were used to study thermal, mechanical and morphological properties of the prepared systems. The best mechanical properties were obtained at EP/PU weight ratio 75/25 which also shows a fine and uniformly dispersed morphology. Moreover, at this ratio, with increasing PTHF Mw in the urethane prepolymer, the mechanical properties were improved whereas a decrease was observed in Tg and thermal degradation temperature of g-IPNs.

scholarly journals Congo Red and Nigrosine Dye Degradation using Dimethyl Dioxirane as an Oxidising Agent

2021 ◽  
Vol 37 (5) ◽  
pp. 1221-1228
Author(s):  
S. Vinotha ◽  
A.Leema Rose
Keyword(s):  
Congo Red ◽  
Room Temperature ◽  
Functional Group ◽  
Dye Degradation ◽  
Visible Spectroscopy ◽  
Before And After ◽  
Ft Ir ◽  
Combined Action ◽  
Uv Visible ◽  
Ft Ir Spectroscopy

The advanced oxidation of Congo red (CR) and Nigrosine (NI) using the combined action of dimethyl dioxirane as an oxidising agent is described in this study. The effects of several parameters, such as the concentration of the oxidising agent, the initial dye concentration, and the pH, have been investigated. At room temperature, the oxidising agent dimethyl dioxirane was employed to test the degradation of CR and NI dyes. On the degradation efficiency of CR and NI, pH’s effects, oxidising agent, and initial dye concentration were examined. The absorbance of CR and NI dyes before and after degradation was measured using UV-visible spectroscopy. The functional group existing in the dyes before and after degradation was determined using FT-IR spectroscopy.

scholarly journals Fabrication of silane-grafted graphene oxide and its effect on the structural, thermal, mechanical, and hysteretic behavior of polyurethane

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Joo Hyung Lee ◽  
Seong Hun Kim
Keyword(s):  
Mechanical Properties ◽  
Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Testing Machine ◽  
Hysteretic Behavior ◽  
Hexamethylene Diisocyanate ◽  
Scanning Calorimetry ◽  
Functionalized Graphene Oxide ◽  
X Ray ◽  
Ft Ir

Abstract Incorporation of nanofillers into polyurethane (PU) is a promising technique for enhancing its thermal and mechanical properties. Silane grafting has been used as a surface treatment for the functionalization of graphene oxide (GO) with numerous reactive sites dispersed on its basal plane and edge. In this study, amine-grafted GO was prepared using silanization of GO with (3-aminopropyl)triethoxysilane. The functionalized graphene oxide (fGO) was characterized by Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy. Next, it was introduced in PU fabricated using polycaprolactone diol, castor oil, and hexamethylene diisocyanate. The fGO–PU nanocomposites were in turn characterized by FT-IR, X-ray diffraction, scanning electron microscopy, differential scanning calorimetry, thermogravimetric analysis, and a universal testing machine. The results obtained from these analyses showed changes in structural thermal properties, as well as improved thermal stability and mechanical properties because of the strong interfacial adhesion between the fGO and the PU matrix.

Bioenveloping Inorganic Filler-Based Eggshell Wastes for Enhancing the Properties of Natural Rubber Biocomposites

2020 ◽  
Author(s):  
Hesham Moustafa ◽  
Soma El-Mogy ◽  
Saber A. Ibrahim ◽  
Anhar Awad ◽  
Nabila A. Darwish
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Infrared Imaging ◽  
Morphological Data ◽  
Inorganic Filler ◽  
Scanning Calorimetry ◽  
Potential Alternative ◽  
Fourier Transform Infrared Imaging ◽  
Ft Ir ◽  
Lower Temperature

ABSTRACT In this study, eggshell (ES) wastes were used as a renewable reinforcing material in natural rubber (NR) composite to limit carbon production. Long bio-alkyd resin (LAR) was also used to envelope the inorganic ES particles and to aid in dispersing the filler in the NR matrix. The effect of the coated ES filler (ESR) in the rubber mix on the morphology, mechanical properties, and swelling was investigated. The ES filler and its biocomposites were characterized by X-ray fluorescence, scanning electron microscopy, Fourier transform infrared imaging microscope (FT-IR-IM), differential scanning calorimetry (DSC), and thermogravimetric analysis. The morphological data reveal that the resin enhances the dispersion of the ES filler in the NR matrix. These data were confirmed by the results obtained from FT-IR-IM. The swelling and mechanical properties were significantly improved when the coated filler was used in NR matrix, especially at 20 wt.% ESR. DSC thermograms revealed that the increase in the resin caused the glass transition temperature (Tg) to be shifted to a lower temperature. The obtained results show that the bioenveloping ESR can be used as potential alternative for green tire and vehicle applications rather than conventional petroleum-based filler.

scholarly journals Microstructure and Mechanical Properties of Composite Resins Subjected to Accelerated Artificial Aging

2013 ◽  
Vol 24 (6) ◽  
pp. 599-604 ◽  
Author(s):  
Andrea Candido dos Reis ◽  
Denise Tornavoi de Castro ◽  
Marco Antonio Schiavon ◽  
Leandro Jardel da Silva ◽  
Jose Augusto Marcondes Agnelli
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Artificial Aging ◽  
Thermal Analyses ◽  
Surface Hardness ◽  
Composite Resins ◽  
Scanning Calorimetry ◽  
Good Thermal Stability ◽  
Microstructure And Mechanical Properties ◽  
Before And After

The aim of this study was to investigate the influence of accelerated artificial aging (AAA) on the microstructure and mechanical properties of the Filtek Z250, Filtek Supreme, 4 Seasons, Herculite, P60, Tetric Ceram, Charisma and Filtek Z100. composite resins. The composites were characterized by Fourier-transform Infrared spectroscopy (FTIR) and thermal analyses (Differential Scanning Calorimetry - DSC and Thermogravimetry - TG). The microstructure of the materials was examined by scanning electron microscopy. Surface hardness and compressive strength data of the resins were recorded and the mean values were analyzed statistically by ANOVA and Tukey's test (α=0.05). The results showed significant differences among the commercial brands for surface hardness (F=86.74, p<0.0001) and compressive strength (F=40.31, p<0.0001), but AAA did not affect the properties (surface hardness: F=0.39, p=0.53; compressive strength: F=2.82, p=0.09) of any of the composite resins. FTIR, DSC and TG analyses showed that resin polymerization was complete, and there were no differences between the spectra and thermal curve profiles of the materials obtained before and after AAA. TG confirmed the absence of volatile compounds and evidenced good thermal stability up to 200 °C, and similar amounts of residues were found in all resins evaluated before and after AAA. The AAA treatment did not significantly affect resin surface. Therefore, regardless of the resin brand, AAA did not influence the microstructure or the mechanical properties.

Sign in / Sign up

Export Citation Format

Share Document