scholarly journals Post-Processing of FDM 3D-Printed Polylactic Acid Parts by Laser Beam Cutting

Polymers ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 550 ◽  
Author(s):  
Mahmoud Moradi ◽  
Mojtaba Karami Moghadam ◽  
Mahmoud Shamsborhan ◽  
Mahdi Bodaghi ◽  
Hamid Falavandi
Keyword(s):  
Process Parameters ◽  
Focal Plane ◽  
Laser Cutting ◽  
Cutting Speed ◽  
Cutting Process ◽  
Poly Lactic Acid ◽  
Regression Equations ◽  
Post Processing ◽  
Fused Deposition ◽  
3D Printed

In this paper, the post-processing of 3D-printed poly lactic acid (PLA) parts is investigated. Workpieces are manufactured by fused deposition modeling (FDM) 3D printing, while they may have defects in some areas such as edges. A post-processing is introduced here for 3D-printed samples by low power CO2 laser. The thickness of the FDM samples are 3.2 mm and printed by optimum conditions. Effects of process parameters such as focal plane position (−3.2–3.2 mm), laser power (20–40 W), and laser cutting speed (1–13 mm/s) are examined based on the design of experiments (DOE). Geometrical features of the kerf; top and bottom kerf; taper; ratio of top to the bottom kerf are considered as output responses. An analysis of the experimental results by statistical software is conducted to survey the effects of process parameters and to obtain regression equations. By optimizing of the laser cutting process; an appropriate kerf quality is obtained and also optimum input parameters are suggested. Experimental verification tests show a good agreement between empirical results and statistical predictions. The best optimum sample with 1.19 mm/s cutting speed, 36.49 W power and 0.53 mm focal plane position shows excellent physical features after the laser cutting process when 276.9 μm top and 261.5 μm bottom kerf width is cut by laser.

scholarly journals Mechanical Properties of FDM Printed PLA Parts before and after Thermal Treatment

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1239
Author(s):  
Ali Chalgham ◽  
Andrea Ehrmann ◽  
Inge Wickenkamp
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Process Parameters ◽  
Fused Deposition Modeling ◽  
Poly Lactic Acid ◽  
Three Point Bending ◽  
Fused Deposition ◽  
Before And After ◽  
Deposition Modeling ◽  
3D Printed

Fused deposition modeling (FDM) is one of the most often-used technologies in additive manufacturing. Several materials are used with this technology, such as poly(lactic acid) (PLA), which is most commonly applied. The mechanical properties of 3D-printed parts depend on the process parameters. This is why, in this study, three-point bending tests were carried out to characterize the influence of build orientation, layer thickness, printing temperature and printing speed on the mechanical properties of PLA samples. Not only the process parameters may affect the mechanical properties, but heat after-treatment also has an influence on them. For this reason, additional samples were printed with optimal process parameters and characterized after pure heat treatment as well as after deformation at a temperature above the glass transition temperature, cooling with applied deformation, and subsequent recovery under heat treatment. These findings are planned to be used in a future study on finger orthoses that could either be printed according to shape or in a flat shape and afterwards heated and bent around the finger.

A Study on the Effect of Process Parameters on Thin NAND Flash Wafer by Multi - Beam Matrix Laser Cutting

2020 ◽  
Vol 830 ◽  
pp. 59-67
Author(s):  
Cheng Zhu Li ◽  
Ruei Han Chen ◽  
Jun Yi Lin ◽  
Liang An Zheng ◽  
Chao Ming Hsu
Keyword(s):  
Process Parameters ◽  
Laser Cutting ◽  
Cutting Speed ◽  
Cutting Process ◽  
Stress And Strain ◽  
Nand Flash ◽  
Analysis Software ◽  
Element Analysis ◽  
Laser Process ◽  
The Finite Element Analysis

This study is designed to investigate the influence of multi-beam matrix laser cutting process on NAND Flash package quality, and find out the important process parameters of multi-beam matrix laser process are defocus amount, laser power, cutting speed and material thickness. Then use the finite element analysis software ANSYS to obtain the minimum temperature influence, stress and strain, and use Taquchi method and variance analysis (ANOVA) to find the optimal temperature combination, the optimal combination of stress and strain and its contribution degree. Finally, the reliability is tested by verification experiments, and the error is found to be within 3.638%. It is confirmed that the optimized parameter combination has high repetitiveness. It is hoped that this study can contribute to the multi-beam matrix laser cutting process.

scholarly journals Pressure Orientation-Dependent Recovery of 3D-Printed PLA Objects with Varying Infill Degree

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1275 ◽  
Author(s):  
Guido Ehrmann ◽  
Andrea Ehrmann
Keyword(s):  
Shape Memory ◽  
Fused Deposition Modeling ◽  
Static Load ◽  
Shape Memory Polymer ◽  
Applied Pressure ◽  
Poly Lactic Acid ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Load Tests ◽  
3D Printed

Poly(lactic acid) is not only one of the most often used materials for 3D printing via fused deposition modeling (FDM), but also a shape-memory polymer. This means that objects printed from PLA can, to a certain extent, be deformed and regenerate their original shape automatically when they are heated to a moderate temperature of about 60–100 °C. It is important to note that pure PLA cannot restore broken bonds, so that it is necessary to find structures which can take up large forces by deformation without full breaks. Here we report on the continuation of previous tests on 3D-printed cubes with different infill patterns and degrees, now investigating the influence of the orientation of the applied pressure on the recovery properties. We find that for the applied gyroid pattern, indentation on the front parallel to the layers gives the worst recovery due to nearly full layer separation, while indentation on the front perpendicular to the layers or diagonal gives significantly better results. Pressing from the top, either diagonal or parallel to an edge, interestingly leads to a different residual strain than pressing from front, with indentation on top always firstly leading to an expansion towards the indenter after the first few quasi-static load tests. To quantitatively evaluate these results, new measures are suggested which could be adopted by other groups working on shape-memory polymers.

Development of three-dimensional printing filaments based on poly(lactic acid)/hydroxyapatite composites with potential for tissue engineering

2021 ◽  
pp. 002199832098856
Author(s):  
Marcela Piassi Bernardo ◽  
Bruna Cristina Rodrigues da Silva ◽  
Luiz Henrique Capparelli Mattoso
Keyword(s):  
Tissue Engineering ◽  
Lactic Acid ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry ◽  
Three Dimensional Printing ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed

Injured bone tissues can be healed with scaffolds, which could be manufactured using the fused deposition modeling (FDM) strategy. Poly(lactic acid) (PLA) is one of the most biocompatible polymers suitable for FDM, while hydroxyapatite (HA) could improve the bioactivity of scaffold due to its chemical composition. Therefore, the combination of PLA/HA can create composite filaments adequate for FDM and with high osteoconductive and osteointegration potentials. In this work, we proposed a different approache to improve the potential bioactivity of 3D printed scaffolds for bone tissue engineering by increasing the HA loading (20-30%) in the PLA composite filaments. Two routes were investigated regarding the use of solvents in the filament production. To assess the suitability of the FDM-3D printing process, and the influence of the HA content on the polymer matrix, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were performed. The HA phase content of the composite filaments agreed with the initial composite proportions. The wettability of the 3D printed scaffolds was also increased. It was shown a greener route for obtaining composite filaments that generate scaffolds with properties similar to those obtained by the solvent casting, with high HA content and great potential to be used as a bone graft.

scholarly journals Effects of Rice Straw Powder (RSP) Size and Pretreatment on Properties of FDM 3D-Printed RSP/Poly(Lactic Acid) Biocomposites

Molecules ◽  
2021 ◽  
Vol 26 (11) ◽  
pp. 3234
Author(s):  
Wangwang Yu ◽  
Lili Dong ◽  
Wen Lei ◽  
Yuhan Zhou ◽  
Yongzhe Pu ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Rice Straw ◽  
Fused Deposition Modeling ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Cost Effective ◽  
Poly Lactic Acid ◽  
Fused Deposition ◽  
Interfacial Compatibility ◽  
3D Printed

To develop a new kind of environment-friendly composite filament for fused deposition modeling (FDM) 3D printing, rice straw powder (RSP)/poly(lactic acid) (PLA) biocomposites were FDM-3D-printed, and the effects of the particle size and pretreatment of RSP on the properties of RSP/PLA biocomposites were investigated. The results indicated that the 120-mesh RSP/PLA biocomposites (named 120#RSP/PLA) showed better performance than RSP/PLA biocomposites prepared with other RSP sizes. Infrared results showed that pretreatment of RSP by different methods was successful, and scanning electron microscopy indicated that composites prepared after pretreatment exhibited good interfacial compatibility due to a preferable binding force between fiber and matrix. When RSP was synergistically pretreated by alkaline and ultrasound, the composite exhibited a high tensile strength, tensile modulus, flexural strength, and flexural modulus of 58.59, 568.68, 90.32, and 3218.12 MPa, respectively, reflecting an increase of 31.19%, 16.48%, 18.75%, and 25.27%, respectively, compared with unmodified 120#RSP/PLA. Pretreatment of RSP also improved the thermal stability and hydrophobic properties, while reducing the water absorption of 120#RSP/PLA. This work is believed to provide highlights of the development of cost-effective biocomposite filaments and improvement of the properties of FDM parts.

scholarly journals On the Post-Processing of 3D-Printed ABS Parts

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1559
Author(s):  
Mohammad Reza Khosravani ◽  
Jonas Schüürmann ◽  
Filippo Berto ◽  
Tamara Reinicke
Keyword(s):  
Surface Treatment ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Acrylonitrile Butadiene Styrene ◽  
Experimental Tests ◽  
Fracture Load ◽  
Post Processing ◽  
Fused Deposition ◽  
Dog Bone ◽  
3D Printed

Application of Additive Manufacturing (AM) has significantly increased in the past few years. AM also known as three-dimensional (3D) printing has been currently used in fabrication of prototypes and end-use products. Considering the new applications of additively manufactured components, it is necessary to study structural details of these parts. In the current study, influence of a post-processing on the mechanical properties of 3D-printed parts has been investigated. To this aim, Acrylonitrile Butadiene Styrene (ABS) material was used to produce test coupons based on the Fused Deposition Modeling (FDM) process. More in deep, a device was designed and fabricated to fix imperfection and provide smooth surfaces on the 3D-printed ABS specimens. Later, original and treated specimens were subjected to a series of tensile loads, three-point bending tests, and water absorption tests. The experimental tests indicated fracture load in untreated dog-bone shaped specimen was 2026.1 N which was decreased to 1951.7 N after surface treatment. Moreover, the performed surface treatment was lead and decrease in tensile strength from 29.37 MPa to 26.25 MPa. Comparison of the results confirmed effects of the surface modification on the fracture toughness of the examined semi-circular bending components. Moreover, a 3D laser microscope was used for visual investigation of the specimens. The documented results are beneficial for next designs and optimization of finishing processes.

EXPERIMENTAL STUDY ON THE CO2 LASER CUTTING OF NOVEL POLYAMIDE 6/FLUOROELASTOMER THERMOPLASTIC ELASTOMERIC BLENDS

2015 ◽  
Vol 88 (1) ◽  
pp. 125-137 ◽  
Author(s):  
Shib Shankar Banerjee ◽  
Anil K. Bhowmick
Keyword(s):  
Low Power ◽  
Co2 Laser ◽  
Process Parameters ◽  
Laser Power ◽  
Laser Cutting ◽  
Manufacturing Industry ◽  
Cutting Speed ◽  
Polyamide 6 ◽  
Thermoplastic Elastomers ◽  
Dynamic Vulcanization

ABSTRACT The application of the low-power CO2 laser-cutting process to fluoroelastomer (FKM), polyamide 6 (PA6), PA6/FKM thermoplastic elastomers (TPEs), and their thermoplastic vulcanizate (TPV) is reported. The main laser process parameters studied were laser power, cutting speed, and material thickness. The value of the top and bottom widths of the slit that were formed during laser cutting (kerf width), melted transverse area, and melted volume per unit time were measured and analyzed. Interestingly, TPE showed a smaller melted area and melted volume per unit time when compared with those values with PA6. Dynamic vulcanization further decreased these values. For example, the melted areas of PA6 and TPE were 510 × 10−3 mm2 and 305 × 10−3 mm2, respectively, which reduced to 238 × 10−3 mm2 for TPV at 40 W laser power. FKM showed the lowest value (melted area of 180 × 10−3 mm2). In addition, the output quality of the cut surface was examined by measuring the root mean square (RMS) roughness of the cut edges and heat-affected zone (HAZ). The obtained results indicated that the dimension of the HAZ and RMS roughness largely decreased in TPE when compared with PA6. For example, the HAZ of PA6 was 700 μm, which decreased to 230 μm for TPE at 40 W laser power. On the other hand, HAZ was nonexistent for FKM. Infrared spectroscopic analysis showed that there was no structural change of TPE or pristine polymers after applying the low-power CO2 laser on the surface of materials. CO2 laser cutting will be a new technique in this industry, and this analysis will assist the manufacturing industry to choose a suitable laser system with exhaustive information of process parameters for cutting or machining of rubber, TPEs, and TPVs.

Investigations of process parameters during dissolution studies of drug loaded 3D printed tablets

2021 ◽  
pp. 095441192199358
Author(s):  
Varun Sharma ◽  
Khaja Moinuddin Shaik ◽  
Archita Choudhury ◽  
Pramod Kumar ◽  
Prateek Kala ◽  
...  
Keyword(s):  
Dissolution Rate ◽  
Process Parameters ◽  
Empirical Relation ◽  
Three Dimensional ◽  
Critical Parameters ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Rate Of Dissolution ◽  
3D Printed ◽  
Percentage Release

The present research paper attempts to study the effect of different process parameters on the dissolution rate during 3D printed tablets. Three-dimensional printing has the potential of serving tailored made tablets to cater personalized drug delivery systems. Fluorescein loaded PVA filaments through impregnation route was used to fabricate tablets based on Taguchi based design of experimentation using Fused Deposition Modelling (FDM). The effect of print speed, infill percentage and layer thickness were analyzed to study the effect on rate of dissolution. Infill percentage followed by print speed were found to be critical parameters affecting dissolution rate. The data analysis provided an insight into the study of interaction among different 3D printing parameters to develop an empirical relation for percentage release of the drug in human body.

Sign in / Sign up

Export Citation Format

Share Document