scholarly journals Degradable Controlled Release Fertilizer Composite Prepared via Extrusion: Fabrication, Characterization, and Release Mechanisms

Polymers ◽  
2020 ◽  
Vol 12 (2) ◽  
pp. 301 ◽  
Author(s):  
Siwen Bi ◽  
Vincenzo Barinelli ◽  
Margaret J. Sobkowicz
Keyword(s):  
Controlled Release ◽  
Biodegradable Polymers ◽  
Polymer Matrix ◽  
Phosphorus Deficiency ◽  
Release Kinetics ◽  
Phosphate Fertilizer ◽  
Water Soluble ◽  
Butylene Succinate ◽  
Urea Phosphate ◽  
Erosion Mechanisms

In this work, biodegradable polymers were melt compounded with urea phosphate to fabricate “smart fertilizers” for sustainable agriculture. Urea phosphate (UP) is typically applied as a water-soluble fertilizer to treat phosphorus deficiency in high pH soils. Due to the low diffusion rate of phosphate through slow-release fertilizer coatings, phosphate supply has been considered the “bottleneck” for nitrogen–phosphorous–potassium (NPK) nutrients supply. We study the influence of polymer matrix structure on release kinetics in deionized water using novel polyesters including poly (hexamethylene succinate) (PHS), poly (30% butylene succinate-co-70% hexamethylene succinate) (PBHS 30/70), and PBHS 70/30. Melt processed composites of UP and polyester were analyzed to determine UP loading efficiency and dispersion and distribution of the salt in the polymer matrix. A combined empirical model involving diffusion and erosion mechanisms was found have a good agreement with the experimental release curve. This work provides a solution for environmentally friendly controlled release phosphate fertilizer with good release performance using bio-based and biodegradable polymers.

scholarly journals DESIGN AND EVALUATION OF CONTROLLED-RELEASE OCULAR INSERTS OF BRIMONIDINE-TARTRATE AND TIMOLOL MALEATE

2016 ◽  
Vol 9 (1) ◽  
pp. 79 ◽  
Author(s):  
Preethi G. B. ◽  
Prashanth Kunal
Keyword(s):  
Controlled Release ◽  
Drug Release ◽  
Sodium Alginate ◽  
Calcium Chloride ◽  
Release Kinetics ◽  
Water Soluble ◽  
Moisture Loss ◽  
Timolol Maleate ◽  
Brimonidine Tartrate

<p><strong>Objective: </strong>The current work was attempted to formulate and evaluate a controlled-release matrix-type ocular inserts containing a combination of brimonidine tartrate and timolol maleate, with a view to sustain the drug release in the cul-de-sac of the eye.<strong></strong></p><p><strong>Methods: </strong>Initially, the infrared studies were done to determine the drug–polymer interactions. Sodium alginate-loaded ocuserts were prepared by solvent casting technique. Varying the concentrations of polymer—sodium alginate, plasticizer—glycerine, and cross-linking agent—calcium chloride by keeping the drug concentration constant, made a total of nine formulations. These formulations were evaluated for its appearance, drug content, weight uniformity, thickness uniformity, percentage moisture loss, percentage moisture absorption, and <em>in vitro </em>release profile of the ocuserts. Finally, accelerated stability studies and the release kinetics were performed on the optimised formulation.<strong></strong></p><p><strong>Results: </strong>It was perceived that polymer, plasticizer, and calcium chloride had a significant influence on the drug release. The data obtained from the formulations showed that formulation—F9 was the optimised formulation, which exhibited better drug release. The release data of the optimised formulation tested on the kinetic models revealed that it exhibited first-order release kinetics. <strong></strong></p><p><strong>Conclusion: </strong>It can be concluded that a natural bioadhesive hydrophilic polymer such as sodium alginate can be used as a film former to load water soluble and hydrophilic drugs like brimonidine tartrate and timolol maleate. Among all formulations, F9 with 400 mg sodium alginate, 2% calcium chloride and 60 mg glycerin were found to be the most suitable insert in terms of appearance, ease of handling, thickness, <em>in vitro</em> drug release and stability.</p>

Controlled Release of Resveratrol and Lignan by Matrix Tableting

2013 ◽  
Vol 746 ◽  
pp. 330-336
Author(s):  
Mont Kumpugdee-Vollrath ◽  
Mario Helmis
Keyword(s):  
Controlled Release ◽  
Release Kinetics ◽  
Research Work ◽  
Magnesium Stearate ◽  
Water Soluble ◽  
Matrix Tablets ◽  
Water Soluble Drug ◽  
The Matrix ◽  
Best Fitting ◽  
Model Drug

The aim of this research work was to develop the controlled release of two model drugs i.e. water insoluble drug - resveratrol and water soluble drug - lignan by matrix tableting with an eccentric tablet machine. For this purpose different kinds of polymers i.e. Metolose 90 SH-4000® (HMPC), Fetocel RT-N-100® (EC) and Eudragit RLPO® (polymethacrylate) were used. The matrix tablets containing 2 %wt of a model drug which were mixed with 5, 10, 20, 30 and 50 %wt of the polymers mentioned above. In addition, a glidant composed of 1 %wt talc and 1 %wt magnesium stearate as well as a filler Ludipress® were processed. Different physical properties of the powder mixtures (e.g. flowability) and of the tablets (e.g. hardness, uniformity of mass or drug content, drug release, etc.) were determined. Most of the tablets met the physical requirements. If the polymer content got higher the release was slower, which can be confirmed by the lower values of k. The release kinetics were described by three typical mathematic models i.e. biphasic, Noyes-Whitney and KorsmeyerPeppas. The best fitting results were ordered as follows: biphasic > Noyes-Witney > KorsmeyerPeppas.

Controlled Release of Tebuconazole from a Polymer Matrix Microparticle:  Release Kinetics and Length of Efficacy

2004 ◽  
Vol 52 (15) ◽  
pp. 4814-4820 ◽  
Author(s):  
Jawed Asrar ◽  
Yiwei Ding ◽  
Rita E. La Monica ◽  
Linda C. Ness
Keyword(s):  
Controlled Release ◽  
Polymer Matrix ◽  
Release Kinetics

Controlled Release of Metformin Hydrochloride I. In vitro Release from Physical Mixture Containing Xanthan Gum as Hydrophilic Rate Retarding Polymer

1970 ◽  
Vol 4 (1) ◽  
Author(s):  
Mashkura Ashrafi ◽  
Jakir Ahmed Chowdhury ◽  
Md Selim Reza
Keyword(s):  
Controlled Release ◽  
Xanthan Gum ◽  
In Vitro Release ◽  
Correlation Coefficients ◽  
High Ratio ◽  
Water Soluble ◽  
Metformin Hydrochloride ◽  
Model Drug ◽  
Very High

Capsules of different formulations were prepared by using a hydrophilic polymer, xanthan gum and a filler Ludipress. Metformin hydrochloride, which is an anti-diabetic agent, was used as a model drug here with the aim to formulate sustained release capsules. In the first 6 formulations, metformin hydrochloride and xanthan gum were used in different ratio. Later, Ludipress was added to the formulations in a percentage of 8% to 41%. The total procedure was carried out by physical mixing of the ingredients and filling in capsule shells of size ‘1’. As metformin hydrochloride is a highly water soluble drug, the dissolution test was done in 250 ml distilled water in a thermal shaker (Memmert) with a shaking speed of 50 rpm at 370C &plusmn 0.50C for 6 hours. After the dissolution, the data were treated with different kinetic models. The results found from the graphs and data show that the formulations follow the Higuchian release pattern as they showed correlation coefficients greater than 0.99 and the sustaining effect of the formulations was very high when the xanthan gum was used in a very high ratio with the drug. It was also investigated that the Ludipress extended the sustaining effect of the formulation to some extent. But after a certain period, Ludipress did not show any significant effect as the pores made by the xanthan gum network were already blocked. It is found here that when the metformin hydrochloride and the xanthan gum ratio was 1:1, showed a high percentage of drug release, i.e. 91.80% of drug was released after 6 hours. But With a xanthan gum and metformin hydrochloride ratio of 6:1, a very slow release of the drug was obtained. Only 66.68% of the drug was released after 6 hours. The percent loading in this case was 14%. Again, when Ludipress was used in high ratio, it was found to retard the release rate more prominently. Key words: Metformin Hydrochloride, Xanthan Gum, Controlled release capsule Dhaka Univ. J. Pharm. Sci. Vol.4(1) 2005 The full text is of this article is available at the Dhaka Univ. J. Pharm. Sci. website

Microsponges: An Overview

2017 ◽  
Vol 4 (4) ◽  
Author(s):  
Hamid Hussain ◽  
Divya Juyal ◽  
Archana Dhyani
Keyword(s):  
Controlled Release ◽  
Delivery System ◽  
Oral Delivery ◽  
Active Agent ◽  
Topical Delivery ◽  
Water Soluble ◽  
Wide Range ◽  
Porous Beads

Microsponge and Nanosponge delivery System was originally developed for topical delivery of drugs can also be used for controlled oral delivery of drugs using water soluble and bioerodible polymers. Microsponge delivery system (MDS) can entrap wide range of drugs and then release them onto the skin over a time by difussion mechanism to the skin. It is a unique technology for the controlled release of topical agents and consists of nano or micro porous beads loaded with active agent and also use for oral delivery of drugs using bioerodible polymers.

Optimization Study to Develop Once-a-day Controlled Release Formulation of Metoclopramide with Predictable Design Space

1970 ◽  
Vol 1 (1) ◽  
pp. 71-76
Author(s):  
Rajesh Dubey ◽  
Udaya K. Chowdary ◽  
Venkateswarlu V.
Keyword(s):  
Controlled Release ◽  
Drug Release ◽  
Design Space ◽  
Release Kinetics ◽  
Release Profile ◽  
Release Formulation ◽  
Linear Effect ◽  
Controlled Release Formulation ◽  
The Difference ◽  
Face Centered

A controlled release formulation of metoclopramide was developed using a combination of hypromellose (HPMC) and hydrogenated castor oil (HCO). Developed formulations released the drug over 20 hr with release kinetics following Higuchi model. Compared to HCO, HPMC showed significantly higher influence in controlling the drug release at initial as well as later phase. The difference in the influence can be explained by the different swelling and erosion behaviour of the polymers. Effect of the polymers on release was optimized using a face-centered central composite design to generate a predictable design space. Statistical analysis of the drug release at various levels indicated a linear effect of the polymers’ levels on the drug release. The release profile of formulations containing the polymer levels at extremes of their ranges in design space was found to be similar to the predicted release profile

Mesoporous Silica Molecular Sieve based Nanocarriers: Transpiring Drug Dissolution Research

2017 ◽  
Vol 23 (3) ◽  
pp. 467-480 ◽  
Author(s):  
Satyanarayan Pattnaik ◽  
Kamla Pathak
Keyword(s):  
Drug Release ◽  
Mesoporous Silica ◽  
Molecular Sieves ◽  
Release Kinetics ◽  
Drug Loading ◽  
Scale Up ◽  
Water Soluble ◽  
Drug Dissolution ◽  
Water Soluble Drugs ◽  
Loading Methods

Background: Improvement of oral bioavailability through enhancement of dissolution for poorly soluble drugs has been a very promising approach. Recently, mesoporous silica based molecular sieves have demonstrated excellent properties to enhance the dissolution velocity of poorly water-soluble drugs. Description: Current research in this area is focused on investigating the factors influencing the drug release from these carriers, the kinetics of drug release and manufacturing approaches to scale-up production for commercial manufacture. Conclusion: This comprehensive review provides an overview of different methods adopted for synthesis of mesoporous materials, influence of processing factors on properties of these materials and drug loading methods. The drug release kinetics from mesoporous silica systems, the manufacturability and stability of these formulations are reviewed. Finally, the safety and biocompatibility issues related to these silica based materials are discussed.

Formulation Development and Characterization of controlled release core in cup matrix tablets of venlafaxine HCl

2020 ◽  
Vol 15 ◽  
Author(s):  
Balaji Maddiboyina ◽  
Vikas Jhawat ◽  
Gandhi Sivaraman ◽  
Om Prakash Sunnapu ◽  
Ramya Krishna Nakkala ◽  
...  
Keyword(s):  
Controlled Release ◽  
Drug Release ◽  
Release Rate ◽  
Zero Order ◽  
Water Soluble ◽  
Matrix Tablets ◽  
Drug Dissolution ◽  
Crystalline Cellulose ◽  
Hydrophobic Polymers

Background: Venlafaxine HCl is a selective serotonin reuptake inhibitor which is given in the treatment of depression. The delivery of the drug at a controlled rate can be of great importance for prolonged effect. Objective: The objective was to prepare and optimize the controlled release core in cup matrix tablet of venlafaxine HCl using the combination of hydrophilic and hydrophobic polymers to prolong the effect with rate controlled drug release. Methods: The controlled release core in cup matrix tablets of venlafaxine HCl were prepared using HPMC K5, K4, K15, HCO, IPA, aerosol, magnesium sterate, hydrogenated castor oil and micro crystalline cellulose PVOK-900 using wet granulation technique. Total ten formulations with varying concentrations of polymers were prepared and evaluated for different physicochemical parameters such FTIR analysis for drug identification, In-vitro drug dissolution study was performed to evaluate the amount of drug release in 24 hrs, drug release kinetics study was performed to fit the data in zero order, first order, Hixson–crowell and Higuchi equation to determine the mechanism of drug release and stability studies for 3 months as observed. Results: The results of hardness, thickness, weight variation, friability and drug content study were in acceptable range for all formulations. Based on the In vitro dissolution profile, formulation F-9 was considered to be the optimized extending the release of 98.32% of drug up to 24 hrs. The data fitting study showed that the optimized formulation followed the zero order release rate kinetics and also compared with innovator product (flavix XR) showed better drug release profile. Conclusion: The core-in-cup technology has a potential to control the release rate of freely water soluble drugs for single administration per day by optimization with combined use of hydrophilic and hydrophobic polymers.

Sign in / Sign up

Export Citation Format

Share Document