scholarly journals Feasibility of Manufacturing Strand-Based Wood Composite Treated with β-Cyclodextrin–Boric Acid for Fungal Decay Resistance

Polymers ◽  
2020 ◽  
Vol 12 (2) ◽  
pp. 274 ◽  
Author(s):  
Lili Cai ◽  
Hyungsuk Lim ◽  
Nicholas C. Fitzkee ◽  
Bojan Cosovic ◽  
Dragica Jeremic
Keyword(s):  
Boric Acid ◽  
Mass Loss ◽  
Chemical Shifts ◽  
Brown Rot ◽  
Decay Resistance ◽  
Attenuated Total Reflection ◽  
Fungal Decay ◽  
Scanning Calorimetry ◽  
Decay Fungi ◽  
Average Mass

The feasibility of using β-cyclodextrin (βCD) as an eco-friendly carrier of boric acid for the protection of strand-based wood composites against decay fungi was evaluated. The formation of a βCD–boric acid (βCD–B) complex was confirmed by the appearance of the boron–oxygen bond by using attenuated total reflection–Fourier transform infrared spectroscopy. Chemical shifts of around 6.25 and 1.41 ppm were also observed in 1H Nuclear Magnetic Resonance (NMR) and 11B NMR spectra, respectively. The βCD–B preservatives at two levels (5 and 10 wt.%) were uniformly blended with southern pine strands that were subsequently sprayed with polymeric methylene diphenyl diisocyanate (pMDI) resin. The blended strands were formed into a loose mat by hand and consolidated into 25 × 254 × 12 mm oriented strand boards (OSB) using a hot-press. The OSB panels were cut to end-matched internal bonding (IB) strength and fungal decay resistance test specimens. The vertical density profiles (VDPs) of the IB specimens were measured using an X-ray based density profiler and the specimens with statistically similar VDPs were selected for the IB and decay tests. The IB strength of the treated specimens was lower than the control specimens but they were above the required IB strength of heavy-duty load-bearing boards for use in humid conditions, specified in the BS EN 300:2006 standard. The reduced IB of preservative-treated OSB boards could be explained by the destabilized resin upon the addition of the βCD–B complex, as indicated by the differential scanning calorimetry (DSC) results. The resistance of the OSB panels against two brown-rot fungi (i.e., G. trabeum or P. placenta) was evaluated before and after accelerated leaching cycles. The treated OSBs exposed to the fungi showed an average mass loss of lower than 3% before leaching, while the untreated OSBs had 49 and 35% mass losses due to decay by G. trabeum or P. placenta, respectively. However, upon the leaching, the treatment provided protection only against G. trabeum to a certain degree (average mass loss of 15%). The experimental results suggest that protection efficacy against decay fungi after leaching, as well as the adhesion of the OSB strands, can be improved by increasing the amount of pMDI resin.

scholarly journals Resistance of thermally modified and pressurized hot water extracted Scots pine sapwood against decay by the brown-rot fungus Rhodonia placenta

2019 ◽  
Vol 78 (1) ◽  
pp. 161-171 ◽  
Author(s):  
Michael Altgen ◽  
Suvi Kyyrö ◽  
Olli Paajanen ◽  
Lauri Rautkari
Keyword(s):  
Cell Wall ◽  
Mass Loss ◽  
Scots Pine ◽  
Elevated Temperatures ◽  
Brown Rot ◽  
Decay Resistance ◽  
Hot Water ◽  
Decay Fungi ◽  
Effective Reduction ◽  
Cell Wall Porosity

AbstractThe thermal degradation of wood is affected by a number of process parameters, which may also cause variations in the resistance against decay fungi. This study compares changes in the chemical composition, water-related properties and decay resistance of Scots pine sapwood that was either thermally modified (TM) in dry state at elevated temperatures (≥ 185 °C) or treated in pressurized hot water at mild temperatures (≤ 170 °C). The thermal decomposition of easily degradable hemicelluloses reduced the mass loss caused by Rhodonia placenta, and it was suggested that the cumulative mass loss is a better indicator of an actual decay inhibition. Pressurized hot water extraction (HWE) did not improve the decay resistance to the same extent as TM, which was assigned to differences in the wood-water interactions. Cross-linking reactions during TM caused a swelling restraint and an effective reduction in moisture content. This decreased the water-swollen cell wall porosity, which presumably hindered the transport of degradation agents through the cell wall and/or reduced the accessibility of wood constituents for degradation agents. This effect was absent in hot water-extracted wood and strong decay occurred even when most hemicelluloses were already removed during HWE.

Growth behavior of wood-destroying fungi in chemically modified wood: wood degradation and translocation of nitrogen compounds

Holzforschung ◽  
2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Lukas Emmerich ◽  
Maja Bleckmann ◽  
Sarah Strohbusch ◽  
Christian Brischke ◽  
Susanne Bollmus ◽  
...  
Keyword(s):  
Protective Action ◽  
Treated Wood ◽  
Untreated Wood ◽  
Brown Rot ◽  
Decay Resistance ◽  
White Rot ◽  
Decay Fungi ◽  
Chemically Modified ◽  
Decay Tests ◽  
Modified Wood

Abstract Chemical wood modification has been used to modify wood and improve its decay resistance. However, the mode of protective action is still not fully understood. Occasionally, outdoor products made from chemically modified timber (CMT) show internal decay while their outer shell remains intact. Hence, it was hypothesized that wood decay fungi may grow through CMT without losing their capability to degrade non-modified wood. This study aimed at developing a laboratory test set-up to investigate (1) whether decay fungi grow through CMT and (2) retain their ability to degrade non-modified wood. Acetylated and 1,3-dimethylol-4,5-dihydroxyethyleneurea (DMDHEU) treated wood were used in decay tests with modified ‘mantle specimens’ and untreated ‘core dowels’. It became evident that white rot (Trametes versicolor), brown rot (Coniophora puteana) and soft rot fungi can grow through CMT without losing their ability to degrade untreated wood. Consequently, full volume impregnation of wood with the modifying agent is required to achieve complete protection of wooden products. In decay tests with DMDHEU treated specimens, significant amounts of apparently non-fixated DMDHEU were translocated from modified mantle specimens to untreated wood cores. A diffusion-driven transport of nitrogen and DMDHEU seemed to be responsible for mass translocation during decay testing.

Decay resistance, extractive content, and water sorption capacity of Siberian larch (Larix sibirica Lebed.) heartwood timber

Holzforschung ◽  
2006 ◽  
Vol 60 (1) ◽  
pp. 99-103 ◽  
Author(s):  
Martti Venäläinen ◽  
Anni M. Harju ◽  
Nasko Terziev ◽  
Tapio Laakso ◽  
Pekka Saranpää
Keyword(s):  
Siberian Larch ◽  
Brown Rot ◽  
Decay Resistance ◽  
Extractive Content ◽  
Strong Negative Correlation ◽  
Average Mass ◽  
Brown Rot Fungi ◽  
Hygroscopic Properties ◽  
Decay Test

Abstract The aim of this study was to find chemical or physical properties of Siberian larch heartwood timber that correlate with the variation in decay resistance. Juvenile heartwood from 24-year-old grafts of 15 clones was exposed to three brown-rot fungi according to the standard in vitro decay test (European standard EN 113). The mass losses caused by the brown rot fungi Coniophora puteana, Poria placenta, and Gloeophyllum trabeum were 20%, 28% and 17% of the dry mass, respectively. The average mass loss over the three fungi had a strong negative correlation with the concentration of taxifolin (r=–0.673, P=0.006), as well as with the concentration of total phenolics determined by the Folin-Ciocalteu assay (r=–0.677, P=0.006). Thus, the concentration of flavonoids is a promising property for indirect measurement of the decay resistance of Siberian larch timber. The most abundant heartwood extractives, arabinogalactans, had a non-significant relationship with the decay resistance, but their concentration correlated positively with the capacity of the wood to adsorb water (r=0.736, P=0.002). The hygroscopic properties of the wood or the wood density were not associated with the decay resistance.

scholarly journals Mode of action of brown rot decay resistance in modified wood: a review

Holzforschung ◽  
2014 ◽  
Vol 68 (2) ◽  
pp. 239-246 ◽  
Author(s):  
Rebecka Ringman ◽  
Annica Pilgård ◽  
Christian Brischke ◽  
Klaus Richter
Keyword(s):  
Cell Wall ◽  
Mode Of Action ◽  
Wood Decay ◽  
Brown Rot ◽  
Decay Resistance ◽  
Hydroxyl Groups ◽  
Decay Fungi ◽  
Brown Rot Decay ◽  
Thermally Modified Wood ◽  
Modified Wood

Abstract Chemically or physically modified wood materials have enhanced resistance to wood decay fungi. In contrast to treatments with traditional wood preservatives, where the resistance is caused mainly by the toxicity of the chemicals added, little is known about the mode of action of nontoxic wood modification methods. This study reviews established theories related to resistance in acetylated, furfurylated, dimethylol dihydroxyethyleneurea-treated, and thermally modified wood. The main conclusion is that only one theory provides a consistent explanation for the initial inhibition of brown rot degradation in modified wood, that is, moisture exclusion via the reduction of cell wall voids. Other proposed mechanisms, such as enzyme nonrecognition, micropore blocking, and reducing the number of free hydroxyl groups, may reduce the degradation rate when cell wall water uptake is no longer impeded.

Genetic variation in the decay resistance of Scots pine wood against brown rot fungus

2001 ◽  
Vol 31 (7) ◽  
pp. 1244-1249 ◽  
Author(s):  
Anni M Harju ◽  
Martti Venäläinen ◽  
Egbert Beuker ◽  
Pirkko Velling ◽  
Hannu Viitanen
Keyword(s):  
Genetic Variation ◽  
Mass Loss ◽  
Scots Pine ◽  
Brown Rot ◽  
Decay Resistance ◽  
Phenotypic Variance ◽  
Increment Core ◽  
Genetic Components ◽  
Brown Rot Fungus ◽  
The Mean

The role of genotype in the durability of Scots pine (Pinus sylvestris L.) wood against decay by brown rot fungus (Coniophora puteana (Schum. ex Fr.) Karst. (strain Bam EBW 15)) was studied in a laboratory test. The wood material was obtained from 32-year-old half-sib progenies of Scots pine. The increment core samples of sapwood and juvenile heartwood were decayed using a modification of the standardized EN 113 method. The mean densities of the sapwood and heartwood samples were 391 and 337 mg·cm–3, respectively, and the mean mass losses were 114 and 80 mg·cm–3, respectively. The additive genetic components were small compared with the total phenotypic variance, which resulted in small narrow-sense heritabilities in mass loss. The most marked feature was the wide phenotypic variation in mass loss observed in heartwood (range 199 mg·cm–3) compared with sapwood (range 72 mg·cm–3) samples. Low heritability, together with the relatively high coefficient of additive genetic variation (CVA) in heartwood mass loss, suggests that advances in breeding can only be made through intensive testing in the environments which the studied experiment represents.

scholarly journals Experimental evidence that fungal symbionts of beetles suppress wood decay by competing with decay fungi

2019 ◽  
Author(s):  
James Skelton ◽  
Andrew Loyd ◽  
Jason A. Smith ◽  
Robert A. Blanchette ◽  
Benjamin W. Held ◽  
...  
Keyword(s):  
Mass Loss ◽  
Wood Decay ◽  
Brown Rot ◽  
Inhibitory Effects ◽  
Ambrosia Beetles ◽  
Decay Fungi ◽  
Bark And Ambrosia Beetles ◽  
Symbiotic Fungi ◽  
Brown Rot Decay ◽  
Forest Biology

Throughout forests worldwide, bark and ambrosia beetles inoculate dead and dying trees with symbiotic fungi. We experimentally determined the effects of three common and widely distributed ascomycete symbionts, and one introduced Asian basidiomycete symbiont on the decay of pine sapwood. Ascomycetes caused less than 5% mass loss and no structural degradation, whereas the basidiomycete Flavodon ambrosius caused nearly 15% mass loss and visible degradation of wood structure. In co-inoculation experiments, the beetle symbionts Ophiostoma ips and Raffaelea fusca reduced white and brown rot decay through competition with Ganoderma curtisii and Phaeolus schweinitzii, respectively. The inhibitory effects of O. ips and R. fusca on decay were negated when co-inoculated with F. ambrosius, suggesting that widespread introduction of this beetle symbiont could alter forest carbon fluxes. In contrast to the predominant forest biology narrative, most bark and ambrosia beetles introduce fungi that delay rather than facilitate tree biomass recycling.

Investigation of fungal decay of poplar wood treated with pistachio resin

BioResources ◽  
2020 ◽  
Vol 16 (1) ◽  
pp. 779-788
Author(s):  
Maede Ahadnezhad ◽  
Soheila Izadyar ◽  
Davood Efhamisisi
Keyword(s):  
Mass Loss ◽  
Trametes Versicolor ◽  
Populus Deltoides ◽  
Treated Wood ◽  
Brown Rot ◽  
White Rot ◽  
White Rot Fungus ◽  
Poplar Wood ◽  
Fungal Decay ◽  
Brown Rot Fungus

The density, swelling, and fungal decay of poplar (Populus deltoides) wood treated with pistachio resin (PR) obtained from Pistacia atlantica were investigated. The white-rot fungus Trametes versicolor and the brown-rot fungus Coniophora puteana were used. Methanolic solutions of PR with different concentrations of 1%, 6%, 12%, and 15% were used as the preservative solution. Wood samples were saturated by two different vacuum/pressure (V/P) and dipping methods. The density, volumetric swelling of treated wood, and their mass loss (ML) caused by fungal decay were determined. The density of treated species increased to 15.4% and 5.8% for V/P and dipping methods, respectively, at 15% PR concentration. The volumetric swelling of the treated samples was reduced to 24.5% and 16.8% for V/P and dipping procedure, respectively, at 15% PR concentration. The mass loss of treated samples after exposure to T. versicolor was less than the untreated one (17.4% for V/P and 22.6% for dipping methods at 15% PR concentration). The results showed the better performance of V/P treatment in promotion of wood durability against fungal decay than the dipping method.

scholarly journals Experimental evidence that fungal symbionts of beetles suppress wood decay by competing with decay fungi

2019 ◽  
Author(s):  
James Skelton ◽  
Andrew Loyd ◽  
Jason A. Smith ◽  
Robert A. Blanchette ◽  
Benjamin W. Held ◽  
...  
Keyword(s):  
Mass Loss ◽  
Wood Decay ◽  
Brown Rot ◽  
Inhibitory Effects ◽  
Ambrosia Beetles ◽  
Decay Fungi ◽  
Bark And Ambrosia Beetles ◽  
Symbiotic Fungi ◽  
Brown Rot Decay ◽  
Forest Biology

Throughout forests worldwide, bark and ambrosia beetles inoculate dead and dying trees with symbiotic fungi. We experimentally determined the effects of three common and widely distributed ascomycete symbionts, and one introduced Asian basidiomycete symbiont on the decay of pine sapwood. Ascomycetes caused less than 5% mass loss and no structural degradation, whereas the basidiomycete Flavodon ambrosius caused nearly 15% mass loss and visible degradation of wood structure. In co-inoculation experiments, the beetle symbionts Ophiostoma ips and Raffaelea fusca reduced white and brown rot decay through competition with Ganoderma curtisii and Phaeolus schweinitzii, respectively. The inhibitory effects of O. ips and R. fusca on decay were negated when co-inoculated with F. ambrosius, suggesting that widespread introduction of this beetle symbiont could alter forest carbon fluxes. In contrast to the predominant forest biology narrative, most bark and ambrosia beetles introduce fungi that delay rather than facilitate tree biomass recycling.

scholarly journals Properties of modified wood according to treatment technology and thermo-vacuum process for birch (Betula pendula Roth) veneers

BioResources ◽  
2020 ◽  
Vol 15 (2) ◽  
pp. 4150-4164
Author(s):  
Anete Meija-Feldmane ◽  
Ignazia Cuccui ◽  
Ilze Irbe ◽  
Andris Morozovs ◽  
Uldis Spulle
Keyword(s):  
Mass Loss ◽  
Betula Pendula ◽  
Brown Rot ◽  
Strength Loss ◽  
Decay Resistance ◽  
Treatment Technology ◽  
Betula Pendula Roth ◽  
Treatment Regimes ◽  
Brown Rot Fungus ◽  
Modified Wood

Thermally modified birch (Betula pendula Roth) veneers that had been subjected to wood treatment technology (WTT) or thermo vacuum (TV) processes were compared in this study. After modification of veneers in the range of temperatures from 160 °C to 218 °C and times from 0.5 h to 3 h, the color, mass loss, density, tensile strength, hygroscopicity, and decay resistance against brown rot fungus Coniophora puteana were determined. Treatment regimes with the greatest mass loss were at 217 °C for 3.0 h in TV (7.8%) and 160 °C for 0.8 h in the WTT (6.7%). As expected, wood mass loss correlated well with moisture exclusion efficiency (MEE) in all relative humidity (RH) environments (r = 0.95 to 0.99). Strength loss in the WTT was considerable compared to the TV process (57% and 40%, respectively). The resistance against brown rot fungus was moderate with a mass loss of 12% to 33%. Among the investigated samples, the regime 217/3.0/TV showed the best resistance against brown rot fungus and acceptable other properties.

scholarly journals Cell Wall Bulking by Maleic Anhydride for Wood Durability Improvement

Forests ◽  
2020 ◽  
Vol 11 (4) ◽  
pp. 367 ◽  
Author(s):  
Mingming He ◽  
Dandan Xu ◽  
Changgui Li ◽  
Yuzhen Ma ◽  
Xiaohan Dai ◽  
...  
Keyword(s):  
Cell Wall ◽  
Maleic Anhydride ◽  
Wood Cell Wall ◽  
Brown Rot ◽  
Decay Resistance ◽  
White Rot ◽  
White Rot Fungus ◽  
Hydroxyl Group ◽  
Hydroxyl Groups ◽  
Decay Fungi

Wood is susceptible to swelling deformation and decay fungi due to moisture adsorption that originates from the dynamic nanopores of the cell wall and the abundant hydroxyl groups in wood components. This study employed as a modifier maleic anhydride (MAn), with the help of acetone as solvent, to diffuse into the wood cell wall, bulk nanopores, and further chemically bond to the hydroxyl groups of wood components, reducing the numbers of free hydroxyl groups and weakening the diffusion of water molecules into the wood cell wall. The derived MAn-bulked wood, compared to the control wood, presented a reduction in water absorptivity (RWA) of ~23% as well as an anti-swelling efficiency (ASE) of ~39% after immersion in water for 228 h, and showed an improvement in decay resistance of 81.42% against white-rot fungus and 69.79% against brown-rot fungus, respectively. The method of combined cell wall bulking and hydroxyl group bonding could effectively improve the dimensional stability and decay resistance with lower doses of modifier, providing a new strategy for wood durability improvement.

Sign in / Sign up

Export Citation Format

Share Document