scholarly journals Synthesis and Application of a Cationic Polyamine as Yankee Dryer Coating Agent for the Tissue Paper-Making Process

Polymers ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 173
Author(s):  
Cesar Valencia ◽  
Yamid Valencia ◽  
Carlos David Grande Tovar
Keyword(s):  
Chemical Properties ◽  
Gel Permeation Chromatography ◽  
Superior Performance ◽  
Production Plant ◽  
Scanning Calorimetry ◽  
Release Agent ◽  
Coating Agent ◽  
Tissue Paper ◽  
Paper Making ◽  
Durability Assessment

Tissue paper is of high importance worldwide and, continuously, research is focused on improvements of the softening and durability properties of the paper which depend specifically on the production process. Polyamide-amine-epichlorohydrin (PAE) resins along with release agents are widely used to adhere the paper to the yankee dryer (creping cylinder) in paper manufacture. Nevertheless, these resins are highly cationic and they normally adhere in excess to the paper which negatively affects the creping process and the quality of the paper. For this reason, a low cationic polyamine-epichlorohydrin coating (Polycoat 38®) was synthesized from a diamine supplied by Disproquin S.A.S. and epichlorohydrin. The analysis of the synthesized polymer was carried out by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance (1H-NMR). The molecular weight of the polymer was obtained by gel permeation chromatography (GPC), physical-chemical properties such as kinematic viscosity, percentage of solids, density, charge density were measured and compared with a commercial PAE resin (Dispro620®) Thermal stability of the Polycoat 38® and glass transition temperature in presence of a release agent (Disprosol 17®) were also evaluated by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC), respectively. Finally, a peel adhesion test and an absorption durability assessment were carried out together with the evaluation of the creeping efficiency of the paper by caliber and tensile measurements in a tissue (towel paper) production plant, demonstrating a superior performance in the paper creping process as compared to some commercially available products.

Copolymer of natural fibre reinforced polyester urethane: effect on physico-chemical properties through modification to interfacial adhesion

2016 ◽  
Vol 36 (2) ◽  
pp. 189-197
Author(s):  
Gabriela Jandikova ◽  
Pavel Kucharczyk ◽  
Norbert Miskolczi ◽  
Alena Pavelkova ◽  
Adriana Kovalcik ◽  
...  
Keyword(s):  
Interfacial Adhesion ◽  
Alkali Treatment ◽  
Chemical Properties ◽  
Gel Permeation Chromatography ◽  
Natural Fibre ◽  
Special Focus ◽  
Scanning Calorimetry ◽  
Polyester Urethane ◽  
Flax Fibres ◽  
Physico Chemical

Abstract This work is dedicated to polyester urethane (PEU)-based biocomposites, with special focus placed on techniques for compatibilisation to heighten interfacial adhesion between the PEU matrix and flax fibres. Tests were conducted on the effects of modification so as to increase interfacial adhesion between the flax fibres and the polyester matrix. These tests involved a commercial silane-based compatibilising additive, two experimentally synthesised agents, oleic acid (OA) and di-tert-butyl peroxide (DTBP). Furthermore, the flax fibres underwent acid or alkali treatment. The biocomposites were characterised by gel permeation chromatography, infrared spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and scanning electron microscopy (SEM). Mechanical properties were investigated through tensile testing. Biocomposites with a commercial silane-based additive and synthesised agent, based on maleic-anhydride, were assessed as the best solution. Nevertheless, all modifications, excluding alkali treatment of fibres, significantly increased the performance of the material.

scholarly journals Effect of E-Beam Irradiation on Thermal and Mechanical Properties of Ester Elastomers Containing Multifunctional Alcohols

Polymers ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 1043 ◽  
Author(s):  
Marta Piątek-Hnat ◽  
Kuba Bomba ◽  
Jakub Pęksiński ◽  
Agnieszka Kozłowska ◽  
Jacek G. Sośnicki ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Chemical Properties ◽  
Sebacic Acid ◽  
Gel Permeation Chromatography ◽  
Tensile Tests ◽  
Synthesis Process ◽  
Resonance Spectroscopy ◽  
Thermal And Mechanical Properties ◽  
Scanning Calorimetry ◽  
Water Contact

The aim of this work was to investigate the thermal and mechanical properties of novel, electron beam-modified ester elastomers containing multifunctional alcohols. Polymers tested in this work consist of two blocks: sebacic acid–butylene glycol block and sebacic acid–sugar alcohol block. Different sugar alcohols were utilized in the polymer synthesis: glycerol, sorbitol, xylitol, erythritol, and mannitol. The polymers have undergone an irradiation procedure. The materials were irradiated with doses of 50 kGy, 100 kGy, and 150 kGy. The expected effect of using ionizing radiation was crosslinking process and improvement of the mechanical properties. Additionally, a beneficial side effect of the irradiation process is sterilization of the affected materials. It is also worth noting that the materials described in this paper do not require either sensitizers or cross-linking agent in order to perform radiation modification. Radiation-modified poly(polyol sebacate-co-butylene sebacate) elastomers have been characterized in respect to the mechanical properties (quasi-static tensile tests), cross-link density, thermal properties (Differential Scanning Calorimetry (DSC)), chemical properties: Fourier transform infrared spectroscopy (FTIR), and wettability (water contact angle). Poly(polyol sebacate-co-butylene sebacate) preopolymers were characterized with nuclear magnetic resonance spectroscopy (1H NMR and 13C NMR) and gel permeation chromatography (GPC). Thermal stability of cross-linked materials (directly after synthesis process) was tested with thermogravimetric analysis (TGA).

scholarly journals Ring-opening polymerization and plasticization of poly(L-lactic)acid by adding of glycerol-dioleate

2021 ◽  
Author(s):  
Tibor Horváth ◽  
Kálmán Marossy ◽  
Tamás J. Szabó
Keyword(s):  
Lactic Acid ◽  
Glass Transition ◽  
Ring Opening ◽  
Chemical Properties ◽  
Gel Permeation Chromatography ◽  
Ring Opening Polymerization ◽  
General Information ◽  
Scanning Calorimetry ◽  
Different Temperatures ◽  
Physical And Chemical

AbstractPoly-L-lactic acid (PLLA) has been produced by ring-opening polymerization method. During the polymerization processes different temperatures and process times have been applied to reach an optimum setup that was used to produce sample. The sample was measured by Fourier-transform infrared spectroscopy (FTIR), gel permeation chromatography (GPC) and differential scanning calorimetry (DSC) methods to identify the structure, molar mass and define the glass transition temperatures of product and obtain general information about the physical and chemical properties of material. Based on the results of measures, the material’s crystallinity was also investigated. The plasticization of PLLA has been also investigated. During the experiments, previously produced material (PLLA synthesized by polycondensation) was plasticised by adding of glycerol-dioleate. The plasticized material was also measured by FTIR, GPC and DSC methods to check the basic physical and chemical parameters of the material. According to the results of the measurements that were found, by this approach, the glass transition temperature of PLLA was reduced by 7 °C that indicated the glycerol-dioleate might act as a plasticizer for PLLA material without any deviation in the chemical structure of material.

COST Action FP1105: effect of raw materials and pulping conditions on the characteristics of dissolved kraft lignins

Holzforschung ◽  
2016 ◽  
Vol 70 (12) ◽  
pp. 1105-1114 ◽  
Author(s):  
Antonia Svärd ◽  
Olena Sevastyanova ◽  
Galina Dobele ◽  
Vilhemina Jurkjane ◽  
Elisabet Brännvall
Keyword(s):  
Wood Species ◽  
Raw Materials ◽  
Black Liquor ◽  
Analytical Data ◽  
Chemical Properties ◽  
Gel Permeation Chromatography ◽  
Total Acid ◽  
Scanning Calorimetry ◽  
Cooking Times ◽  
Technical Lignins

Abstract The composition, molecular weight (MW), and chemical structure of technical lignins as byproducts of pulping influence their application in terms of physical and chemical properties, reactivity, and performance. It is important to know how the analytical data of technical lignins are influenced by the wood species and the parameters of pulping. The present study focuses on kraft pulping and how the wood species (eucalyptus, pine, and spruce) and variable cooking times influence the characteristics of dissolved lignins. The black liquor (BL) was recovered after three different cooking times and the precipitated lignin was characterized by total acid hydrolysis including the determination of the acid insoluble part (Klason lignin, KL) and the sugars in the hydrolysate, elemental analysis, 31P NMR spectroscopy, analytical pyrolysis (Py-GC/MS), gel permeation chromatography (GPC), thermogravimetry (TG), and differential scanning calorimetry (DSC). The results indicate that the phenolic OH content, MW and glass transition temperature increased with longer cooking times for the softwood (SW) lignins. These lignins had also a higher MW (Mw 5500–8000 g mol-1), than the eucalyptus lignin (Mw 2200–2400 g mol-1). Eucalyptus lignin had higher sulfur content compared to SW.

PLGA+HA/βTCP scaffold incorporating simvastatin: a promising biomaterial for bone tissue engineering

2020 ◽  
Author(s):  
Mariane Beatriz Sordi ◽  
Ariadne Cristiane Cabral da Cruz ◽  
Águedo Aragones ◽  
Mabel Mariela Rodríguez Cordeiro ◽  
Ricardo de Souza Magini
Keyword(s):  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Thermal Analyses ◽  
Chemical Properties ◽  
Biological Properties ◽  
Scanning Calorimetry ◽  
Evaporation Technique ◽  
Porosity Analysis ◽  
Biphasic Ceramic

The aim of this study was to synthesize, characterize, and evaluate degradation and biocompatibility of poly(lactic-co-glycolic acid) + hydroxyapatite / β-tricalcium phosphate (PLGA+HA/βTCP) scaffolds incorporating simvastatin (SIM) to verify if this biomaterial might be promising for bone tissue engineering. Samples were obtained by the solvent evaporation technique. Biphasic ceramic particles (70% HA, 30% βTCP) were added to PLGA in a ratio of 1:1. Samples with SIM received 1% (m:m) of this medication. Scaffolds were synthesized in a cylindric-shape and sterilized by ethylene oxide. For degradation analysis, samples were immersed in PBS at 37 °C under constant stirring for 7, 14, 21, and 28 days. Non-degraded samples were taken as reference. Mass variation, scanning electron microscopy, porosity analysis, Fourier transform infrared spectroscopy, differential scanning calorimetry, and thermogravimetry were performed to evaluate physico-chemical properties. Wettability and cytotoxicity tests were conducted to evaluate the biocompatibility. Microscopic images revealed the presence of macro, meso, and micropores in the polymer structure with HA/βTCP particles homogeneously dispersed. Chemical and thermal analyses presented very similar results for both PLGA+HA/βTCP and PLGA+HA/βTCP+SIM. The incorporation of simvastatin improved the hydrophilicity of scaffolds. Additionally, PLGA+HA/βTCP and PLGA+HA/βTCP+SIM scaffolds were biocompatible for osteoblasts and mesenchymal stem cells. In summary, PLGA+HA/βTCP scaffolds incorporating simvastatin presented adequate structural, chemical, thermal, and biological properties for bone tissue engineering.

scholarly journals Biocompatibility studies of polyurethane electrospun membranes based on arginine as chain extender

2021 ◽  
Vol 32 (9) ◽  
Author(s):  
Georgina Alejandra Venegas-Cervera ◽  
Andrés Iván Oliva ◽  
Alejandro Avila-Ortega ◽  
José Manuel Cervantes-Uc ◽  
Leydi Maribel Carrillo-Cocom ◽  
...  
Keyword(s):  
Fourier Transforms ◽  
Cell Attachment ◽  
Human Fibroblasts ◽  
Gel Permeation Chromatography ◽  
Electrospinning Process ◽  
Chain Extender ◽  
Cellular Interaction ◽  
Scanning Calorimetry ◽  
Polyurethane Membranes ◽  
Electrospun Membranes

AbstractElectrospun polymers are an example of multi-functional biomaterials that improve the material-cellular interaction and aimed at enhancing wound healing. The main objective of this work is to fabricate electrospun polyurethane membranes using arginine as chain extender (PUUR) in order to test the fibroblasts affinity and adhesion on the material and the polymer toxicity. Polyurethane membranes were prepared in two steps: (i) the polyurethane synthesis, and ii) the electrospinning process. The membranes were characterized by scanning electron microscopy (SEM), Fourier transforms infrared spectroscopy, gel permeation chromatography, and differential scanning calorimetry techniques. The evaluation of PUUR as a scaffolding biomaterial for growing and developing of cells on the material was realized by LIVE/DEAD staining. The results show that the fluorescent surface area of human fibroblasts (hFB), was greater in control dense membranes made from Tecoflex than in electrospun and dense PUUR. From SEM analysis, the electrospun membranes show relatively uniform attachment of cells with a well-spread shape, while Tecoflex dense membranes show a non-proliferating round shape, which is attributed to the fiber’s structure in electrospun membranes. The cell morphology and the cell attachment assay results reveal the well spreading of hFB cells on the surface of electrospun PUUR membranes which indicates a good response related to cell adhesion.

scholarly journals Recycling Potential for Non-Valorized Plastic Fractions from Electrical and Electronic Waste

Recycling ◽  
2021 ◽  
Vol 6 (2) ◽  
pp. 33
Author(s):  
Laura Strobl ◽  
Thomas Diefenhardt ◽  
Martin Schlummer ◽  
Tanja Leege ◽  
Swetlana Wagner
Keyword(s):  
Flame Retardants ◽  
Electronic Waste ◽  
Gel Permeation Chromatography ◽  
Scanning Calorimetry ◽  
Separation Processes ◽  
Melt Flow Rate ◽  
Density Fractions ◽  
Material Recycling ◽  
Other Substances ◽  
Electrical And Electronic Waste

This paper describes a study for waste of electrical and electronic equipment (WEEE) to characterise the plastic composition of different mixed plastic fractions. Most of the samples studied are currently excluded from material recycling and arise as side streams in state-of-the-art plastics recycling plants. These samples contain brominated flame retardants (BFR) or other substances of concern listed as persistent organic pollutants or in the RoHS directive. Seventeen samples, including cathode ray tube (CRT) monitors, CRT televisions, flat screens such as liquid crystal displays, small domestic appliances, and information and communication technology, were investigated using density- and dissolution-based separation processes. The total bromine and chlorine contents of the samples were determined by X-ray fluorescence spectroscopy, indicating a substantial concentration of both elements in density fractions above 1.1 g/cm3, most significantly in specific solubility classes referring to ABS and PS. This was further supported by specific flame retardant analysis. It was shown that BFR levels of both polymers can be reduced to levels below 1000 ppm by dissolution and precipitation processes enabling material recycling in compliance with current legislation. As additional target polymers PC and PC-ABS were also recycled by dissolution but did not require an elimination of BFR. Finally, physicochemical investigations of recycled materials as gel permeation chromatography, melt flow rate, and differential scanning calorimetry suggest a high purity and indicate no degradation of the technical properties of the recycled polymers.

Identification of Amber and the Copal under Heat Pressurized Process

2012 ◽  
Vol 554-556 ◽  
pp. 2112-2115
Author(s):  
Hui Li ◽  
Xuan Wang ◽  
Yong Zhu ◽  
Qin Ren
Keyword(s):  
Chemical Properties ◽  
Peak Position ◽  
Exothermic Peak ◽  
Endothermic Peak ◽  
Scanning Calorimetry ◽  
Natural Resin ◽  
Before And After ◽  
Artificial Heat ◽  
Physical And Chemical ◽  
And Chemical Properties

Amber and copal belong to the natural resin, which are similar and transitional in the physical and chemical properties. The artificial heat-pressurized treatment is contributed to the polymerization of the natural copal, and turns into green, yellow-green and deep orange-yellow copal. It is very difficult to identify amber from the heat- pressurized treatment copal only based on the gemological parameters.The thermal behavior of amber and the copal before and after heat-pressurized treatment were analyzed by means of differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy(FTIR) and nuclear magnetic resonance(NMR). The results show that amber exists an evident endothermic peak around 123~132°C, and copal reveals an obvious endothermic peak at about 174~178°C, and the heat pressurized treatment copal occurs a clear exothermic peak around 150~152°C. The differences between endothermic or exothermic transition and peak position reveal occurring thermal oxidation or the bond breaking or the melting, which are of great significance in the identification.

Synthesis, characterization and corrosion protection properties of polyN-(p-bromophenyl)-2-methacrylamide-co-glycidyl methacrylate on low nickel stainless steel

2011 ◽  
Vol 31 (2-3) ◽  
Author(s):  
Sakvai Mohammed Safiullah ◽  
Deivasigamani Thirumoolan ◽  
Kottur Anver Basha ◽  
K. Mani Govindaraju ◽  
Dhanraj Gopi ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Corrosion Protection ◽  
Glycidyl Methacrylate ◽  
Electrochemical Impedance ◽  
Thermo Gravimetric Analysis ◽  
Gel Permeation Chromatography ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Protection Efficiency ◽  
Ft Ir

Abstract The synthesis of copolymers from different feed ratios of N-(p-bromophenyl)-2- methacrylamide (PBPMA) and glycidyl methacrylate (GMA) was achieved by using free radical solution polymerization technique and characterized using FT-IR, 1H and 13C NMR spectroscopy. The thermal stability of the synthesized copolymers was studied using thermo-gravimetric analysis (TGA) and differential scanning calorimetry (DSC). The molecular weight of the copolymer is determined by gel permeation chromatography (GPC). The corrosion performances of low nickel stainless steel specimens dip coated with different composition of copolymers were investigated in 0.5 M H2SO4 using potentiodynamic polarization and electrochemical impedance spectroscopic (EIS) techniques. The polarization and impedance measurements showed different corrosion protection efficiency with change in composition of the copolymers. It was found that the corrosion protection properties are owing to the barrier effect of the polymer layer covered on the low nickel stainless steel surfaces. However, it is observed that the mole ratio of PBPMA and GMA plays a major role in the protective nature of the copolymer.

scholarly journals Synthesis and Characterization of a Multifunctional Conjugated Polymer

2018 ◽  
Vol 2018 ◽  
pp. 1-9 ◽  
Author(s):  
Emerson C. G. Campos ◽  
Cristiano Zanlorenzi ◽  
Bruno F. Nowacki ◽  
Gabriela M. Miranda ◽  
Denis A. Turchetti ◽  
...  
Keyword(s):  
Conjugated Polymer ◽  
Molar Mass ◽  
Photophysical Properties ◽  
Gel Permeation Chromatography ◽  
Thermal Characterization ◽  
Polymer Structure ◽  
Synthesis And Characterization ◽  
Metallic Ions ◽  
Scanning Calorimetry

This work reports the synthesis and characterization of a conjugated polymer based on fluorene and terpyridine, namely, poly[(9,9-bis(3-((S)-2-methylbutylpropanoate))fluorene-alt-6,6′-(2,2′:6′,2′′-terpyridin-6-yl)] (LaPPS71). The structure was characterized by 1H and 13C nuclear magnetic resonance (NMR) and Fourier-transform infrared (FTIR) spectroscopy. The molar mass was measured by gel permeation chromatography (GPC). As thermal characterization, the glass transition temperature (Tg) was measured by differential scanning calorimetry (DSC). The polymer structure contains two sites capable of complexation with metallic ions, affording the possibility of obtainment of independent or electronically coupled properties, depending on the complexation site. The photophysical properties were fully explored in solution and solid state, presenting ideal results for the preparation of various metallopolymers, in addition to potential application as a metamaterial, due to the presence of the chiral center in the side chains of the polymer.

Sign in / Sign up

Export Citation Format

Share Document