scholarly journals New Epoxy Thermosets Derived from Clove Oil Prepared by Epoxy-Amine Curing

Polymers ◽  
2019 ◽  
Vol 12 (1) ◽  
pp. 44 ◽  
Author(s):  
David Santiago ◽  
Dailyn Guzmán ◽  
Xavier Ramis ◽  
Francesc Ferrando ◽  
Àngels Serra
Keyword(s):  
Renewable Resources ◽  
Crosslinking Density ◽  
Curing Process ◽  
Scanning Calorimetry ◽  
Compact Structure ◽  
Good Thermal Stability ◽  
Epoxy Amine ◽  
Epoxy Monomer ◽  
Amine Curing ◽  
Crosslinking Agents

New thermosets from a triglycidyl eugenol derivative (3EPOEU) as a renewable epoxy monomer were obtained by an epoxy-amine curing process. A commercially-available Jeffamine® and isophorone diamine, both obtained from renewable resources, were used as crosslinking agents, and the materials obtained were compared with those obtained from a standard diglycidylether of bisphenol A (DGEBA). The evolution of the curing process was studied by differential scanning calorimetry and the materials obtained were characterized by means of calorimetry, thermogravimetry, thermodynamomechanical analysis, stress–strain tests and microindentation. 3EPOEU formulations were slightly less reactive, and the thermosets obtained showed higher Tgs than those prepared from DGEBA, since they had higher crosslinking density than formulations with DGEBA because of the more compact structure and higher functionality of the eugenol derivative. 3EPOEU thermosets showed good thermal stability and mechanical properties. The results obtained in this study allow us to conclude that the triglycidyl derivative of eugenol, 3EPOEU, is a safe and environmentally friendly alternative to DGEBA.

Effect of epoxy monomer structure on the curing process and thermo-mechanical characteristics of tri-functional epoxy/amine systems: a methodology combining atomistic molecular simulation with experimental analyses

2017 ◽  
Vol 8 (13) ◽  
pp. 2016-2027 ◽  
Author(s):  
Liang Gao ◽  
Qingjie Zhang ◽  
Hao Li ◽  
Siruo Yu ◽  
Weihong Zhong ◽  
...  
Keyword(s):  
Molecular Simulation ◽  
Experimental Research ◽  
Mechanical Characteristics ◽  
Curing Process ◽  
Epoxy Amine ◽  
Monomer Structure ◽  
System P ◽  
Epoxy Monomer ◽  
Amine System ◽  
Experimental Analyses

A methodology, which combined molecular simulation with experimental research, was established to expound the performance of a tri-functional epoxy/amine system.

Highly Uniform Oriented Liquid Crystalline Thermosets

1996 ◽  
Vol 425 ◽  
Author(s):  
E. Amendola ◽  
C. Carfagna ◽  
M. Giamberini ◽  
L. Komitov
Keyword(s):  
Liquid Crystal ◽  
Aromatic Amines ◽  
Liquid Crystalline ◽  
Crosslinking Density ◽  
External Factors ◽  
Curing Process ◽  
Epoxy Monomer ◽  
Surface Liquid ◽  
Highly Uniform

AbstractCuring of mesogenic epoxy monomer p-Bis(2, 3-epoxypropoxy)-cz-methylstilbene (DOMS) with aromatic amines is discussed. The crosslinking density is controlled using a mixture of biand tetra-functional hardener. The unidirectional alignment of the molecules was achieved during the curing process by external factors such as surface-liquid crystal interactions.

scholarly journals The influence of montmorillonite content on the kinetics of curing of epoxy nanocomposites

2012 ◽  
Vol 66 (6) ◽  
pp. 863-870
Author(s):  
Mirjana Jovicic ◽  
Oskar Bera ◽  
Jelena Pavlicevic ◽  
Vesna Simendic ◽  
Radmila Radicevic
Keyword(s):  
Isoconversional Methods ◽  
Curing Process ◽  
Heating Rates ◽  
Epoxy Nanocomposites ◽  
Scanning Calorimetry ◽  
Epoxy Amine ◽  
Friedman Method ◽  
Kinetics Of ◽  
Dsc Curves ◽  
Energy Activation

In this work, the attention was paid at the investigation of montmorillonite dispersion in epoxy/amine systems due to improved final properties of the nanocomposites. The influence of different montmorillonite content on the kinetics of curing of epoxy/Jeffamine D-230 systems was followed by differential scanning calorimetry (DSC). The curing of epoxy nanocomposites was performed using dynamic regime at three different heating rates: 5, 10 and 20?C/min. Three isoconversional methods were applied: two integral (Ozawa-Flynn-Wall and Kissinger-Akahira-Sunose methods) and one differential (Friedman method). The presence of montmorillonite (MMT) causes the beginning of curing at lower temperatures. The shape of the DSC curves has been changed by the addition of MMT, supporting the hypothesis of a change in the reaction mechanism. For hybrids with 3 and 5 wt.% of MMT, the E? dependence is very similar to those found for the reference system (epoxy/Jeffamine D-230) for the curing degree less than 60%. The hybrid with 10 wt.% of MMT has lower energy activation in regard to the referent system without montmorillonite. Greater differences are observed in the second part of the reaction, where it is known that the curing process is more controlled by diffusion (?>0.60). The Ea value increases at the end of the reaction (??1), which was observed for all systems, and is more pronounced in the presence of montmorillonite.

scholarly journals Improved Processing and Properties for Polyphenylene Oxide Modified by Diallyl Orthophthalate Prepolymer

Polymers ◽  
2019 ◽  
Vol 11 (12) ◽  
pp. 2016
Author(s):  
Honghua Wang ◽  
Qilin Mei ◽  
Yujie Ding ◽  
Zhixiong Huang ◽  
Minxian Shi
Keyword(s):  
Differential Scanning Calorimetry ◽  
Thermal Properties ◽  
Phase Separation ◽  
Dilution Effect ◽  
Gradual Decrease ◽  
Gel Point ◽  
Dynamic Mode ◽  
Curing Process ◽  
Scanning Calorimetry ◽  
Polyphenylene Oxide

Diallyl orthophthalate (DAOP) prepolymer was investigated as a reactive plasticizer to improve the processability of thermoplastics. The rheology of blends of DAOP prepolymer initiated by 2,3-dimethyl-2,3-diphenylbutane (DMDPB) and polyphenylene oxide (PPO) was monitored during the curing process, and their thermal properties and morphology in separated phases were also studied. Differential scanning calorimetry (DSC) results showed that the cure degree of the reactively plasticized DAOP prepolymer was reduced with increasing PPO due to the dilution effect. The increasing amount of the DAOP prepolymer led to a gradual decrease in the viscosity of the blends and the rheology behavior was consistent with the chemical gelation of DAOP prepolymer in blends. This indicated that the addition of the DAOP prepolymer effectively improved processability. The phase separation occurring during curing of the blend and the transition from the static to dynamic mode significantly influences the development of the morphology of the blend corresponding to limited evolution of the conversion around the gel point.

scholarly journals Recycling Waste Cotton Cloths for the Isolation of Cellulose Nanocrystals: A Sustainable Approach

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 626
Author(s):  
Siti Hajar Mohamed ◽  
Md. Sohrab Hossain ◽  
Mohamad Haafiz Mohamad Kassim ◽  
Mardiana Idayu Ahmad ◽  
Fatehah Mohd Omar ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Cellulose Nanocrystals ◽  
Value Added ◽  
Crystallinity Index ◽  
Attenuated Total Reflection ◽  
Cellulose Content ◽  
Scanning Calorimetry ◽  
Good Thermal Stability ◽  
Alkaline Pulping ◽  
Hydrolysis Of Cellulose

There is an interest in the sustainable utilization of waste cotton cloths because of their enormous volume of generation and high cellulose content. Waste cotton cloths generated are disposed of in a landfill, which causes environmental pollution and leads to the waste of useful resources. In the present study, cellulose nanocrystals (CNCs) were isolated from waste cotton cloths collected from a landfill. The waste cotton cloths collected from the landfill were sterilized and cleaned using supercritical CO2 (scCO2) technology. The cellulose was extracted from scCO2-treated waste cotton cloths using alkaline pulping and bleaching processes. Subsequently, the CNCs were isolated using the H2SO4 hydrolysis of cellulose. The isolated CNCs were analyzed to determine the morphological, chemical, thermal, and physical properties with various analytical methods, including attenuated total reflection-Fourier transform-infrared spectroscopy (ATR-FTIR), field-emission scanning electron microscopy (FE-SEM), energy-filtered transmission electron microscopy (EF-TEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The results showed that the isolated CNCs had a needle-like structure with a length and diameter of 10–30 and 2–6 nm, respectively, and an aspect ratio of 5–15, respectively. Additionally, the isolated CNCs had a high crystallinity index with a good thermal stability. The findings of the present study revealed the potential of recycling waste cotton cloths to produce a value-added product.

Cure and Dynamic-Mechanical Behaviors of Vinyl Ester Resinfilled with Multi-Walled Carbon Nanotubes

2010 ◽  
Vol 150-151 ◽  
pp. 1413-1416 ◽  
Author(s):  
Hong Yan Chen ◽  
Zhen Xing Kong ◽  
Ji Hui Wang
Keyword(s):  
Carbon Nanotubes ◽  
Vinyl Ester ◽  
Mechanical Response ◽  
Cure Kinetics ◽  
Crosslinking Density ◽  
Vinyl Ester Resin ◽  
Scanning Calorimetry ◽  
Dynamic Mechanical ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

The cure kinetics of Derakane 411-350, a kind of vinyl ester resin, and its suspensions containing multi-walled carbon nanotubes( MWCNTs) were investigated via non-isothermal dynamic scanning calorimetry (DSC) measurements. The results showed that incorporation of MWCNTs into vinyl ester resin excessively reduces polymerization degree and crosslinking density of vinyl ester resin. For suppressing the negative effect caused by nanotubes, the higher temperature initiator combined with the initiator MEKP was used. Dynamic-mechanical Behavior testing was then carried out on the cured sample in order to relate the curing behavior of MWCNTs modified resin suspensions to mechanical response of their resulting nanocomposites. It was revealed that nanocomposites containing MWCNTs possessed larger storage modulus values as well as higher glass transition temperatures (Tg) as compared to those without MWCNTs after using mixed intiators system to improve the degree of cure.

Semi-bio-based aromatic polyamides from 2,5-furandicarboxylic acid: toward high-performance polymers from renewable resources

RSC Advances ◽  
2016 ◽  
Vol 6 (90) ◽  
pp. 87013-87020 ◽  
Author(s):  
Kaiju Luo ◽  
Yan Wang ◽  
Junrong Yu ◽  
Jing Zhu ◽  
Zuming Hu
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Molecular Weight ◽  
High Molecular Weight ◽  
Renewable Resources ◽  
High Performance ◽  
Good Thermal Stability ◽  
Aromatic Polyamides ◽  
High Performance Polymers ◽  
Furandicarboxylic Acid

Aromatic furanic polyamides with relatively high molecular weight were synthesized, and good thermal stability and mechanical properties were demonstrated.

scholarly journals Cure Kinetics and Inverse Analysis of Epoxy-Amine Based Adhesive Used for Fastening Systems

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3853
Author(s):  
Bilen Emek Abali ◽  
Michele Zecchini ◽  
Gilda Daissè ◽  
Ivana Czabany ◽  
Wolfgang Gindl-Altmutter ◽  
...  
Keyword(s):  
Inverse Analysis ◽  
Building Materials ◽  
Cure Kinetics ◽  
Accurate Estimation ◽  
Curing Process ◽  
Degree Of Cure ◽  
Material Parameters ◽  
Epoxy Amine ◽  
Thermosetting Polymers ◽  
Material Equation

Thermosetting polymers are used in building materials, for example adhesives in fastening systems. They harden in environmental conditions with a daily temperature depending on the season and location. This curing process takes hours or even days effected by the relatively low ambient temperature necessary for a fast and complete curing. As material properties depend on the degree of cure, its accurate estimation is of paramount interest and the main objective in this work. Thus, we develop an approach for modeling the curing process for epoxy based thermosetting polymers. Specifically, we perform experiments and demonstrate an inverse analysis for determining parameters in the curing model. By using calorimetry measurements and implementing an inverse analysis algorithm by using open-source packages, we obtain 10 material parameters describing the curing process. We present the methodology for two commercial, epoxy based products, where a statistical analysis provides independence of material parameters leading to the conclusion that the material equation is adequately describing the material response.

Decellularized liver-regenerative 3D printing biomaterials for cell-based liver therapies via a designed procedure combined with papain-containing reagent treatments and supercritical fluids

2021 ◽  
pp. 1-8
Author(s):  
Ching-Cheng Huang
Keyword(s):  
3D Printing ◽  
Thermo Gravimetric Analysis ◽  
Extraction Process ◽  
Gravimetric Analysis ◽  
Collagen Scaffolds ◽  
Scanning Calorimetry ◽  
Porcine Liver ◽  
Good Thermal Stability ◽  
Decellularized Liver ◽  
Liver Collagen

BACKGROUND: The biologic scaffolds derived from decellularized tissues and organs have been successfully developed in a variety of preclinical and/or clinical studies. OBJECTIVE: The new decellularized liver-regenerative 3D printing biomaterials were designed and prepared for cell-based liver therapies. METHODS: An extraction process was employed to remove the tissue and cellular molecules from porcine liver via pretreatment of supercritical fluid of carbon dioxide (ScCO2). Varying porosities of the decellularized liver tissues were created using papain-containing reagent treatments after ScCO2. RESULTS: The resulting liver-regenerative 3D printing biomaterials of decellularized liver collagen scaffolds were characterized by Fourier transform infrared spectroscopy, thermo-gravimetric analysis, differential scanning calorimetry and scanning electron microscopy. CONCLUSIONS: The decellularized liver collagen scaffolds with good thermal stability (>150 °C) were obtained and employed as liver-regenerative 3D printing biomaterials for cell-based liver therapies.

Sign in / Sign up

Export Citation Format

Share Document