scholarly journals Modified Epoxy Resin Synthesis from Phosphorus—Containing Polyol and Physical Changes Studies in the Synthesized Products

Polymers ◽  
2019 ◽  
Vol 11 (12) ◽  
pp. 2116 ◽  
Author(s):  
Jeong Beom Jang ◽  
Tae Hee Kim ◽  
Taeyoon Kim ◽  
Hye Jin Kim ◽  
Bongkuk Seo ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Epoxy Resins ◽  
Mechanical And Thermal Properties ◽  
Release Rates ◽  
Molding Compounds ◽  
Reinforced Plastics ◽  
Phosphorus Containing ◽  
Physical Changes ◽  
Modified Epoxy

Epoxy resins are commonly used to manufacture the molding compounds, reinforced plastics, coatings, or adhesives required in various industries. However, the demand for new epoxy resins has increased to satisfy diverse industrial requirements such as enhanced mechanical properties, thermal stability, or electrical properties. Therefore, in this study, we synthesized new epoxy resin (PPME) by modifying phosphorous-containing polyol. The prepared resin was analyzed and added to epoxy compositions in various quantities. The compositions were cured at high temperatures to obtain plastics to further test the mechanical and thermal properties of the epoxy resin. The measured tensile and flexural strength of epoxy compositions were similar to the composition without synthesized epoxy resin. However, the heat release rates of the compositions exhibited tendencies of a decrease proportional to the amount of PPME.

The Mechanical Properties of Organic Modified Epoxy Resin

2020 ◽  
Vol 43 (3) ◽  
pp. 10-14
Author(s):  
Georgel MIHU ◽  
Claudia Veronica UNGUREANU ◽  
Vasile BRIA ◽  
Marina BUNEA ◽  
Rodica CHIHAI PEȚU ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Epoxy Resin ◽  
Epoxy Matrix ◽  
Epoxy Resins ◽  
Mechanical Tests ◽  
Organic Modification ◽  
Three Point Bending ◽  
Modified Epoxy

Epoxy resins have been presenting a lot of scientific and technical interests and organic modified epoxy resins have recently receiving a great deal of attention. For obtaining the composite materials with good mechanical proprieties, a large variety of organic modification agents were used. For this study gluten and gelatin had been used as modifying agents thinking that their dispersion inside the polymer could increase the polymer biocompatibility. Equal amounts of the proteins were milled together and the obtained compound was used to form 1 to 5% weight ratios organic agents modified epoxy materials. To highlight the effect of these proteins in epoxy matrix mechanical tests as three-point bending and compression were performed.

scholarly journals A bio-based phosphaphenanthrene-containing derivative modified epoxy thermosets with good flame retardancy, high mechanical properties and transparency

RSC Advances ◽  
2021 ◽  
Vol 11 (49) ◽  
pp. 30943-30954
Author(s):  
Wei Peng ◽  
Yu-xuan Xu ◽  
Shi-bin Nie ◽  
Wei Yang
Keyword(s):  
Mechanical Properties ◽  
Flame Retardant ◽  
Flame Retardancy ◽  
Epoxy Resins ◽  
Flame Retardants ◽  
The Past ◽  
Phosphorus Containing ◽  
Modified Epoxy

Phosphorus-containing flame retardants have received huge interest for improving the flame retardant behavior of epoxy resins (EP) over the past few decades.

Solvent Exchange to Exfoliate Graphene Oxides into Epoxy with Improved Mechanical and Thermal Properties

2015 ◽  
Vol 1110 ◽  
pp. 69-72
Author(s):  
Fu Ke Wang ◽  
Chao Bin He
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Epoxy Resins ◽  
Mechanical And Thermal Properties ◽  
Curing Agent ◽  
Solvent Exchange ◽  
Thermal And Mechanical Properties ◽  
Graphene Oxides ◽  
Curing Agents ◽  
Exchange Technique

The dispersion and exfoliation of graphene oxides in polymer matrix remains a challenge for graphene oxides based epoxy nanocomposites fabrication. In the present paper, we reported a simple and facile solvent exchange technique to successfully transfer graphene oxides (GOs) from aqueous solution to ethanol. In addition, we found that GO dispersion in epoxy resins was affected by the curing agents. Good dispersion of GOs in epoxy resin together with enhanced thermal and mechanical properties were observed when epoxy was cured with aliphatic curing agents. For aromatic curing agent, high loading of GOs leaded to GOs aggregation, but well dispersed GOs was observed at low loading of GOs. Especially, a 12 °C increase of glass transition temperature of the epoxy resin was observed with only 0.1 wt% GOs was added to the epoxy resin.

scholarly journals Mechanical and thermal properties of triblock copolymer modified epoxy resins

BIBECHANA ◽  
2018 ◽  
Vol 16 ◽  
pp. 196-203 ◽  
Author(s):  
Shankar P Khatiwada ◽  
Sabu Thomas ◽  
Jean Marc Saiter ◽  
Ralf Lach ◽  
Rameshwar Adhikari
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resins ◽  
Triblock Copolymer ◽  
Mechanical Performance ◽  
Triblock Copolymers ◽  
Diglycidyl Ether ◽  
Mechanical And Thermal Properties ◽  
Thermal And Mechanical Properties ◽  
Thermoset Resin ◽  
Modified Epoxy

We investigate the ways of improving thermal and mechanical properties of diglycidyl ether of bisphenol-A (DGEBA) based thermoset resin using diaminodiphenylsulphone (DDS) as hardener and using epoxidized polystyrene/polybutadiene-based triblock copolymers as modifier. The epoxidation was performed. The targeted chemical modification using meta-chloroperoxybenzoic acid (m-CPBA) of the copolymer was performed whereby the epoxidation of the butadiene chains mainly took place at 1,4 linkages. The modification copolymer was found to contribute in enhancing the mechanical performance of the blends with epoxy resin. The results indicated the formation of nanostructured morphology in the blends attributable to their enhanced impact strength.BIBECHANA 16 (2019) 196-203

Thermal Stabilities and the Thermal Degradation Kinetics Study of the Flame Retardant Epoxy Resins

2014 ◽  
Vol 1053 ◽  
pp. 263-267 ◽  
Author(s):  
Xiu Juan Tian
Keyword(s):  
Thermal Stability ◽  
Thermal Degradation ◽  
Flame Retardant ◽  
Epoxy Resin ◽  
Epoxy Resins ◽  
Degradation Kinetics ◽  
Thermal Degradation Kinetics ◽  
Thermal Stabilities ◽  
Degradation Kinetic ◽  
Modified Epoxy

Thermal stability and thermal degradation kinetics of epoxy resins with 2-(Diphenylphosphinyl)-1, 4-benzenediol were investegated by thermogravimetric analysis (TGA) at different heating rates of 5 K/min, 10 K/min, 20 K/min and 40 K/min. The thermal degradation kinetic mechanism and models of the modified epoxy resins were determined by Coast Redfern method.The results showed that epoxy resins modified with the flame retardant had more thermal stability than pure epoxy resin. The solid-state decomposition mechanism of epoxy resin and the modified epoxy resin corresponded to the controlled decelerating ځ˽̈́˰̵̳͂͆ͅ˼˰̴̱̾˰̸̵̈́˰̵̸̳̱̹̽̾̓̽˰̶̳̹̾̈́̿̾̓ͅ˰̶˸ځ˹˰̵̵͇͂˰̃˸́˽ځ˹2/3. The introduction of phosphorus-containing flame retardant reduced thermal degradation rate of epoxy resins in the primary stage, and promote the formation of carbon layer.

Mechanichal Properties of DGEBA/TEPA Modified Epoxy Resin

2014 ◽  
Vol 775-776 ◽  
pp. 588-592
Author(s):  
Camila Rodrigues Amaral ◽  
Ruben Jesus Sanchez Rodriguez ◽  
Magno Luiz Tavares Bessa ◽  
Verônica Scarpini Cândido ◽  
Sergio Neves Monteiro
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Epoxy Resin ◽  
Yield Stress ◽  
Diglycidyl Ether ◽  
Notch Toughness ◽  
Epoxy Network ◽  
Structural Network ◽  
Flexural Tests ◽  
Modified Epoxy

The correlation between the structural network of a diglycidyl ether of the bisphenol-A (DGEBA) epoxy resin, modified by two distinct aliphatic amines (tetraethylenepentamine TEPA and jeffamine D230), and its mechanical properties, was investigated as possible matrix for abrasive composites applications. Both flexural tests, to determine the yield stress and the elastic modulus, as well as impact tests to determine the notch toughness, were performed. The DGEBA/D230 presented the highest stiffness and toughness but lowest yield stress. This epoxy network also displayed a greater plastic deformation during fracture.

Preparation and Mechanical Properties of Epoxy Resin Reinforced with Jeffamines-Grafted Carbon Nanotubes

2009 ◽  
Vol 79-82 ◽  
pp. 553-556 ◽  
Author(s):  
Ling Fei Shi ◽  
Gang Li ◽  
Gang Sui ◽  
Xiao Ping Yang
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Epoxy Resin ◽  
Photoelectron Spectroscopy ◽  
Epoxy Matrix ◽  
Resin Matrix ◽  
Mechanical And Thermal Properties ◽  
Time Dynamic ◽  
Multi Walled Carbon Nanotubes ◽  
The Impact

The increasing proliferation and application of advanced polymer composites requires higher and broader performance resin matrices. Poly(oxypropylene) with –NH2 end-groups has been widely used to toughen epoxy resins, but the strength of resin matrix may be reduced due to the addition of flexible segments in the crosslinking network. Carbon nanotubes (CNTs) have been paid more and more attention in recent years because of their superior thermal and mechanical properties. In this paper, CNTs grafted with Jeffamines T403 were used to simultaneously improve the reinforcement and toughening of an epoxy resin. The untreated multi-walled carbon nanotubes (u-MWNTs) were functionalized with amine groups according to three steps: carboxylation, acylation, and amidation. The f-MWNTs were characterized by Fourier transform infra-red (FTIR) and X-ray photoelectron spectroscopy (XPS). The experimental results indicated that the T403 was grafted to the surface of MWCNTs. The mechanical and thermal properties of epoxy with f-MWNTs were investigated. The tensile and flexural strength increased by 7.77 % and 7.03 % after adding 0.5wt% f-MWCNTs without sacrificing the impact toughness. At the same time, dynamic mechanical thermal analysis (DMTA) showed that the glass transition temperature (Tg) of epoxy with f-MWNTs were increased. The fracture surface of epoxy with f-MWNTs was observed by scanning electron microscopy (SEM) to understand the dispersion of f-MWNTs in epoxy matrix and interfacial adhesion between f-MWNTs and epoxy matrix, which can be attributed to the strong interfacial bonding between f-MWNTs and epoxy resin.

Thermo Mechanical behaviour of Phenol Novolac Resin and Unsaturated Polyester Toughened Epoxy using nano Bentonite and Silica Nanoparticles

2020 ◽  
Vol 1 (3) ◽  
pp. 77-83
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Silica Nanoparticles ◽  
Moisture Absorption ◽  
Unsaturated Polyester ◽  
Physical And Mechanical Properties ◽  
Bending Test ◽  
Mechanical And Thermal Properties ◽  
Novolac Epoxy ◽  
Industrial Needs

Phenol novolac epoxy resin is a polymer matter which its properties can be modified for industrial needs. In this research, nanocomposites of phenol novolac epoxy resin and unsaturated polyester are made nano Bentonite and silica nanoparticles as filler. For this purpose, effect of nanoparticles percent on nanocomposite formation is studied and their physical, mechanical and thermal properties are obtained. The presence of unsaturated polyester in this process forms a cross-link capable of improving the physical and mechanical properties of epoxy resin. Fracture behavior was determined by a SEM device. Moreover, TGA, DSC, impact tests and bending test were applied for data analysis. When process ability is growing, moisture absorption decreases. Fracture toughness was also evaluated in a stoichiometric network. Physical and mechanical properties improve significantly with increasing nanoparticles. The most important reason for using this nanocomposite is its high resistance to corrosion.

Sign in / Sign up

Export Citation Format

Share Document