scholarly journals A Quarterthiophene-Based Dye as an Efficient Interface Modifier for Hybrid Titanium Dioxide/Poly(3-hexylthiophene)(P3HT) Solar Cells

Polymers ◽  
2019 ◽  
Vol 11 (11) ◽  
pp. 1752 ◽  
Author(s):  
Arumugam Pirashanthan ◽  
Thanihaichelvan Murugathas ◽  
Neil Robertson ◽  
Punniamoorthy Ravirajan ◽  
Dhayalan Velauthapillai
Keyword(s):  
Titanium Dioxide ◽  
Solar Cells ◽  
Spectral Response ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Hole Mobility ◽  
Short Circuit Current ◽  
Acid Group ◽  
Open Circuit ◽  
Absorption Data

This work focused on studying the influence of dyes, including a thiophene derivative dye with a cyanoacrylic acid group ((E)-2-cyano-3-(3′,3′′,3′′′-trihexyl-[2,2′:5′,2′′:5′′,2′′′- quaterthiophene]-5-yl) acrylicacid)(4T), on the photovoltaic performance of titanium dioxide (TiO2)/poly(3-hexyl thiophene)(P3HT) solar cells. The insertion of dye at the interface improved the efficiency regardless of the dye used. However, 4T dye significantly improved the efficiency by a factor of three when compared to the corresponding control. This improvement is mainly due to an increase in short circuit current density (JSC), which is consistent with higher hole-mobility reported in TiO2/P3HT nanocomposite with 4T dye. Optical absorption data further revealed that 4T extended the spectral response of the TiO2/P3HT nanocomposite, which could also enhance the JSC. The reduced dark current upon dye insertion ensured the carrier recombination was controlled at the interface. This, in turn, increased the open circuit voltage. An optimized hybrid TiO2/P3HT device with 4T dye as an interface modifier showed an average efficiency of over 2% under-simulated irradiation of 100 mWcm−2 (1 sun) with an Air Mass 1.5 filter.

scholarly journals Direct AFM-based nanoscale mapping and tomography of open-circuit voltages for photovoltaics

2018 ◽  
Vol 9 ◽  
pp. 1802-1808 ◽  
Author(s):  
Katherine Atamanuk ◽  
Justin Luria ◽  
Bryan D Huey
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Three Dimensional ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic Properties ◽  
Order Of Magnitude ◽  
Individual Grains

The nanoscale optoelectronic properties of materials can be especially important for polycrystalline photovoltaics including many sensor and solar cell designs. For thin film solar cells such as CdTe, the open-circuit voltage and short-circuit current are especially critical performance indicators, often varying between and even within individual grains. A new method for directly mapping the open-circuit voltage leverages photo-conducting AFM, along with an additional proportional-integral-derivative feedback loop configured to maintain open-circuit conditions while scanning. Alternating with short-circuit current mapping efficiently provides complementary insight into the highly microstructurally sensitive local and ensemble photovoltaic performance. Furthermore, direct open-circuit voltage mapping is compatible with tomographic AFM, which additionally leverages gradual nanoscale milling by the AFM probe essentially for serial sectioning. The two-dimensional and three-dimensional results for CdTe solar cells during in situ illumination reveal local to mesoscale contributions to PV performance based on the order of magnitude variations in photovoltaic properties with distinct grains, at grain boundaries, and for sub-granular planar defects.

scholarly journals Molecular-level architectural design using benzothiadiazole-based polymers for photovoltaic applications

2017 ◽  
Vol 13 ◽  
pp. 863-873 ◽  
Author(s):  
Vinila N Viswanathan ◽  
Arun D Rao ◽  
Upendra K Pandey ◽  
Arul Varman Kesavan ◽  
Praveen C Ramamurthy
Keyword(s):  
Molecular Orbital ◽  
Architectural Design ◽  
Density Functional ◽  
Short Circuit ◽  
Energy Levels ◽  
Photovoltaic Performance ◽  
Hole Mobility ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Lowest Unoccupied Molecular Orbital

A series of low band gap, planar conjugated polymers, P1 (PFDTBT), P2 (PFDTDFBT) and P3 (PFDTTBT), based on fluorene and benzothiadiazole, was synthesized. The effect of fluorine substitution and fused aromatic spacers on the optoelectronic and photovoltaic performance was studied. The polymer, derived from dithienylated benzothiodiazole and fluorene, P1, exhibited a highest occupied molecular orbital (HOMO) energy level at −5.48 eV. Density functional theory (DFT) studies as well as experimental measurements suggested that upon substitution of the acceptor with fluorine, both the HOMO and lowest unoccupied molecular orbital (LUMO) energy levels of the resulting polymer, P2, were lowered, leading to a higher open circuit voltage and short circuit current with an overall improvement of more than 110% for the photovoltaic devices. Moreover, a decrease in the torsion angle between the units was also observed for the fluorinated polymer P2 due to the enhanced electrostatic interaction between the fluorine substituents and sulfur atoms, leading to a high hole mobility. The use of a fused π-bridge in polymer P3 for the enhancement of the planarity as compared to the P1 backbone was also studied. This enhanced planarity led to the highest observed mobility among the reported three polymers as well as to an improvement in the device efficiency by more than 40% for P3.

The Effect of Al-BSF on Seff and Rb in Industrialized Mono-Silicon Solar Cells

2012 ◽  
Vol 472-475 ◽  
pp. 1846-1850
Author(s):  
Shan Shan Dai ◽  
Gao Jie Zhang ◽  
Xiang Dong Luo ◽  
Jing Xiao Wang ◽  
Wen Jun Chen ◽  
...  
Keyword(s):  
Solar Cells ◽  
Spectral Response ◽  
Short Circuit ◽  
Rear Surface ◽  
Surface Recombination ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Surface Recombination Velocity ◽  
Silicon Solar Cells ◽  
Back Surface

In this work, the effect of aluminum back surface field formed by screen printed various amount of Al paste on the effective rear surface recombination velocity (Seff) and the internal rear reflectance coeffeicient (Rb) of commercial mono-silicon solar cells was investigated. We demonstrated the effect of Seffand Rbon the performance of Al-BSF solar cells by simulating them with PC1D. The simulated results showed that the lower Seffcould get higher open circuit voltage (Voc), at the same time, the larger Rbcould get higher short-circuit current (Isc). Experimentally, we investigated the Seffand Rbthrough depositing Al paste with various amount (3.7, 5, 6, and 8 mg/cm2) for fabricating Al-BSF mono-silicon solar cells. Four group cells were characterized by light I-V, spectral response, hemispherical reflectance and scanning electron microscope (SEM) measurements. It was found that, a minimum Seffof 350 cm/s was gotten from the cells with Al paste of 8 mg/cm2, which was extracted by matching quantum efficiency (QE) from 800 nm to 1200 nm with PC1D, and a maximum Rbof 53.5% was obtained from Al paste of 5 mg/cm2by calculating at 1105 nm with PC1D. When the amount of Al paste was higher than 5mg/cm2, there were less Seffand lower Rb. On the other hand, when Al amount was 3.7mg/cm2, it was too little to form a closed BSF. Based on the SEM graphs and simulations with PC1D, a simple explaination was proposed for the experimental results.

scholarly journals Benzothiadiazole Based Cascade Material to Boost the Performance of Inverted Ternary Organic Solar Cells

Energies ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 450 ◽  
Author(s):  
Miron Krassas ◽  
Christos Polyzoidis ◽  
Pavlos Tzourmpakis ◽  
Dimitriοs M. Kosmidis ◽  
George Viskadouros ◽  
...  
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Fused Ring ◽  
Electron Cascade ◽  
First Time

A conjugated, ladder-type multi-fused ring 4,7-dithienbenzothiadiazole:thiophene derivative, named as compound ‘T’, was for the first time incorporated, within the PTB7:PC71BM photoactive layer for inverted ternary organic solar cells (TOSCs) realization. The effective energy level offset caused by compound T between the polymeric donor and fullerene acceptor materials, as well as its resulting potential as electron cascade material contribute to an enhanced exciton dissociation, electron transfer facilitator and thus improved overall photovoltaic performance. The engineering optimization of the inverted TOSC, ITO/PFN/PTB7:Compound T(5% v/v):PC71BM/MoO3/Al, resulted in an overall power conversion efficiency (PCE) of 8.34%, with a short-circuit current density (Jsc) of 16.75 mA cm−2, open-circuit voltage (Voc) of 0.74 V and a fill factor (FF) of 68.1%, under AM1.5G illumination. This photovoltaic performance was improved by approximately 12% with respect to the control binary device.

HYBRID ORGANIC SOLAR CELLS BLENDED WITH CNTs

2015 ◽  
Vol 22 (06) ◽  
pp. 1550072
Author(s):  
SUDIP ADHIKARI ◽  
HIDEO UCHIDA ◽  
MASAYOSHI UMENO
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Photovoltaic Device ◽  
Device Fabrication ◽  
Walled Cnts

In this paper, composite carbon nanotubes (C-CNTs); single-walled CNTs (SWCNTs) and multi-walled CNTs (MWCNTs) are synthesized using an ultrasonic nebulizer in a large quartz tube for photovoltaic device fabrication in poly-3-octyl-thiophene (P3OT)/ n - Si heterojunction solar cells. We found that the device fabricated with C-CNTs shows much better photovoltaic performance than that of a device without C-CNTs. The device with C-CNTs shows open-circuit voltage (Voc) of 0.454 V, a short circuit current density (Jsc) of 12.792 mA/cm2, fill factor (FF) of 0.361 and power conversion efficiency of 2.098 %. Here, we proposed that SWCNTs and MWCNTs provide efficient percolation paths for both electron and hole transportation to opposite electrodes and leading to the suppression of charge carrier recombination, thereby increasing the photovoltaic device performance.

Effect of CdCl2 Treatment of CdS Films on CdTe/CdS Solar Cells

1996 ◽  
Vol 426 ◽  
Author(s):  
W. Song ◽  
D. Mao ◽  
L. Feng ◽  
Y. Zhu ◽  
M. H. Aslan ◽  
...  
Keyword(s):  
Solar Cells ◽  
Spectral Response ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
X Ray Diffraction ◽  
Cdcl2 Treatment ◽  
The Difference ◽  
Cds Films

AbstractWe investigated the effect of CdCl2 treatment of CdS films on the photovoltaic performance of polycrystalline CdTe/CdS solar cells. X-ray diffraction studies indicated that the diffusion of S into CdTe is qualitatively the same for CdTe/CdS films fabricated with both as-deposited and CdCl2-treated CdS. A major difference was observed in the extent of Te diffusion into CdS for the two types of CdS films. Full conversion of CdS into CdS1-yTey; was observed for films prepared with asdeposited CdS, while the formation of the ternary phase was below the detection limit for films prepared with CdCl2-treated CdS. Photoluminescence measurements confirmed this result. The difference in interdiffusion leads to differences in optical transmission of CdS films and spectral response of CdTe/CdS solar cells. An increase of 2.7 mA/cm2 in short-circuit current density was observed as a result of improved spectral response in the wavelength range of 500–600 nm for the CdCl2-treated CdS.

Fabrication of Core-Shell Structured TiO2/MgO Electrodes for Dye-Sensitized Solar Cells

2015 ◽  
Vol 787 ◽  
pp. 3-7 ◽  
Author(s):  
S. Karuppuchamy ◽  
C. Brundha
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Core Shell ◽  
Dye Sensitized ◽  
The Core ◽  
Sensitized Solar Cells

We demonstrated the construction and performance of dye-sensitized solar cells (DSCs) based on nanoparticles of TiO2coated with thin shells of MgO by simple solution growth technique. The XRD patterns confirm the presence of both TiO2and MgO in the core-shell structure. The effect of varied shell thickness on the photovoltaic performance of the core-shell structured electrode is also investigated. We found that MgO shells of all thicknesses perform as barriers that improve open-circuit voltage (Voc) of the DSCs only at the expense of a larger decrease in short-circuit current density (Jsc). The energy conversion efficiency was greatly dependent on the thickness of MgO on TiO2film, and the highest efficiency of 4.1% was achieved at the optimum MgO shell layer.

scholarly journals Steady Enhancement in Photovoltaic Properties of Fluorine Functionalized Quinoxaline-Based Narrow Bandgap Polymer

Molecules ◽  
2018 ◽  
Vol 24 (1) ◽  
pp. 54 ◽  
Author(s):  
Zhonglian Wu ◽  
Huanxiang Jiang ◽  
Xingzhu Wang ◽  
Lei Yan ◽  
Wei Zeng ◽  
...  
Keyword(s):  
Fill Factor ◽  
Polymer Solar Cells ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Hole Mobility ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Promising Candidate ◽  
Photovoltaic Properties ◽  
Narrow Bandgap

To investigate the influence of fluoride phenyl side-chains onto a quinoxaline (Qx) unit on the photovoltaic performance of the narrow bandgap (NBG) photovoltaic polymers, herein, two novel NBG copolymers, PBDTT-DTQx and PBDTT-DTmFQx, were synthesized and characterized. 2-ethylhexylthiothiophene-substituted benzodithiophene (BDTT), 2,3-diphenylquinoxaline (DQx) [or 2,3-bis(3-fluorophenyl)quinoxaline (DmFQx)] and 2-ethylhexylthiophene (T) were used as the electron donor (D) unit, electron-withdrawing acceptor (A) unit and π-bridge, respectively. Compared to non-fluorine substituted PBDTT-DTQx, fluoride PBDTT-DTmFQx exhibited a wide UV-Vis absorption spectrum and high hole mobility. An enhanced short-circuit current (Jsc) and fill factor (FF) simultaneously gave rise to favorable efficiencies in the polymer/PC71BM-based polymer solar cells (PSCs). Under the illumination of AM 1.5G (100 mW cm−2), a maximum power conversion efficiency (PCE) of 6.40% was achieved with an open-circuit voltage (Voc) of 0.87 V, a Jsc of 12.0 mA cm−2 and a FF of 61.45% in PBDTT-DTmFQx/PC71BM-based PSCs, while PBDTT-DTQx-based devices also exhibited a PCE of 5.43%. The excellent results obtained demonstrate that PBDTT-DTmFQx by fluorine atom engineering could be a promising candidate for organic photovoltaics.

scholarly journals Improving the Morphology of the Perovskite Absorber Layer in Hybrid Organic/Inorganic Halide Perovskite MAPbI3 Solar Cells

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
I. J. Ogundana ◽  
S. Y. Foo
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
High Performance ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Perovskite Layer ◽  
Large Variability

Recently, perovskite solar cells have attracted tremendous attention due to their excellent power conversion efficiency, low cost, simple fabrications, and high photovoltaic performance. Furthermore, the perovskite solar cells are lightweight and possess thin film and semitransparency. However, the nonuniformity in perovskite layer constitutes a major setback to the operation mechanism, performance, reproducibility, and degradation of perovskite solar cells. Therefore, one of the main challenges in planar perovskite devices is the fabrication of high quality films with controlled morphology and least amount of pin-holes for high performance thin film perovskite devices. The poor reproducibility in perovskite solar cells hinders the accurate fabrication of practical devices for use in real world applications, and this is primarily as a result of the inability to control the morphology of perovskites, leading to large variability in the characteristics of perovskite solar cells. Hence, the focus of research in perovskites has been mostly geared towards improving the morphology and crystallization of perovskite absorber by selecting the optimal annealing condition considering the effect of humidity. Here we report a controlled ambient condition that is necessary to grow uniform perovskite crystals. A best PCE of 7.5% was achieved along with a short-circuit current density of 15.2 mA/cm2, an open-circuit voltage of 0.81 V, and a fill factor of 0.612 from the perovskite solar cell prepared under 60% relative humidity.

Preparation of Narrow-gap a-Si:H Solar Cells by VHF-PECVD Technique

2010 ◽  
Vol 1245 ◽  
Author(s):  
Do Yun Kim ◽  
Ihsanul Afdi Yunaz ◽  
Shunsuke Kasashima ◽  
Shinsuke Miyajima ◽  
Makoto Konagai
Keyword(s):  
Thin Films ◽  
Solar Cells ◽  
Solar Cell ◽  
Spectral Response ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Hydrogen Flow ◽  
Long Wavelength

AbstractOptical, electrical and structural properties of silicon films depending on hydrogen flow rate (RH), substrate temperature (TS), and deposition pressure (PD) were investigated. By decreasing RH and increasing TS and PD, the optical band gap (Eopt) of silicon thin films drastically declined from 1.8 to 1.63 eV without a big deterioration in electrical properties. We employed all the investigated Si thin films for p-i-n structured solar cells as absorbers with i-layer thickness of 300 nm. From the measurement of solar cell performances, it was clearly observed that spectral response in long wavelength was enhanced as Eopt of absorber layers decreased. Using the solar cell whose Eopt of i-layer was 1.65 eV, the highest QE at long wavelength with the short circuit current density (Jsc) of 16.34 mA/cm2 was achieved, and open circuit voltage (Voc), fill factor (FF), and conversion efficiency (η) were 0.66 V, 0.57, and 6.13%, respectively.

Sign in / Sign up

Export Citation Format

Share Document