scholarly journals Durable Epoxy@ZnO Coating for Improvement of Hydrophobicity and Color Stability of Wood

Polymers ◽  
2019 ◽  
Vol 11 (9) ◽  
pp. 1388 ◽  
Author(s):  
Vu Manh Tuong ◽  
Nguyen Van Huyen ◽  
Nguyen Trong Kien ◽  
Nguyen Van Dien
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Spray Coating ◽  
Color Stability ◽  
Xrd Analysis ◽  
Hexagonal Structure ◽  
Raw Material ◽  
Water Contact ◽  
Nanoscale Structures ◽  
Average Water

The hydrophobicity and color stability of wood are important properties that can be easily changed when wood is used as a raw material for outdoor products, reducing the service life of wood. Herein, an epoxy@ZnO coating was applied by a two-step simple spray coating method to improve the hydrophobicity and color stability of Styrax tonkinensis wood. The hydrophobicity, robustness of coating, as well as the color stability of uncoated wood samples and epoxy@ZnO coated wood samples were evaluated. The microstructure morphology and crystal structures of the coating were also characterized by a field-emission scanning electron microscope (FESEM) and X-ray diffraction (XRD) analysis, respectively. Results showed that the obtained epoxy@ZnO coating was not only superhydrophobic with an average water contact angle of 154.1°, but also maintained superhydrophobicity with an average water contact angle of 149.6° after five water jetting tests. The color stability of the coated wood samples was improved by around 50% compared to that of uncoated wood samples. Additionally, a continuous epoxy@ZnO coating with hierarchical micro/nanoscale structures constructed by the wurtzite hexagonal structure of ZnO micro/nanoparticles on wood surfaces was confirmed.

Fast and simple fabrication of SiO2/poly(vinylidene fluoride) coated cotton fabrics with asymmetric wettability via a facile spray-coating route

2018 ◽  
Vol 89 (6) ◽  
pp. 1013-1026 ◽  
Author(s):  
Rongrong Yu ◽  
Mingwei Tian ◽  
Lijun Qu ◽  
Shifeng Zhu ◽  
Jianhua Ran ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Contact Angle ◽  
Water Contact Angle ◽  
Vinylidene Fluoride ◽  
Spray Coating ◽  
Cotton Fabrics ◽  
Water Repellent ◽  
Water Contact ◽  
Repellent Property ◽  
Poly Vinylidene Fluoride

Cotton fabrics with hydrophilic-to-hydrophobic asymmetric surfaces are attractive as potential utilizable structures for functional garments. The spray-coating route could be deemed as a fast and simple way to achieve asymmetric surfaces. In this paper, SiO2 nanoparticles with size ∼ 205 nm were synthesized via the modified sol-gel method, and then modified with poly(vinylidene fluoride) (PVDF) to form a hydrophobic surface. The SiO2 nanoparticles modified with PVDF were uniformly deposited on the outer surface of cotton fabric aided with the robust air flow force from the sprayer. The morphology and chemical structures were characterized by scanning electron microscopy, mapping, atomic force microscopy, X-ray photoelectron spectroscopy and Fourier-transform infrared spectroscopy. The results indicated that SiO2 nanoparticles were evenly deposited on the surface of cotton fibers and stable interfacial interaction occurred between SiO2 and PVDF molecular chains. The existence of SiO2 could increase the roughness of the fabric surface, which could enhance the water-repellent property of the coated fabrics. Furthermore, the water-repellent property and thermal insulation properties were evaluated via the water contact angle and thermal conductivity tests, respectively, and the results showed that 20 wt.% SiO2/PVDF fabric achieved a desirable level of contact angle, 136.6°, which was the largest water contact angle among all the samples, and the lowest thermal conductivity of 0.033 W/mK, resulting from the existence of SiO2 nanoparticles. Such a fast and simple spray-coating strategy could be widely introduced into asymmetric fabric modification, and such asymmetric fabrics with reasonable water-repellent and thermal insulating outer surfaces could act as candidates in the field of functional garments.

scholarly journals The Synthesis of a Superhydrophobic and Thermal Stable Silica Coating via Sol-Gel Process

Coatings ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 627 ◽  
Author(s):  
Karmele Vidal ◽  
Estíbaliz Gómez ◽  
Amaia Martínez Goitandia ◽  
Adrián Angulo-Ibáñez ◽  
Estíbaliz Aranzabe
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Sol Gel ◽  
Hydrophobic Surface ◽  
Silica Coating ◽  
Water Contact ◽  
Silica Coatings ◽  
Sol Gel Process ◽  
Average Water ◽  
Infrared Spectrometer

A super-hydrophobic surface at a high temperature (400 °C) using the sol-gel method with tetraethoxysilane (TEOS) and methyltriethoxysilane (MTES) as precursors has been obtained. The effects of the coatings’ ages, deposited times and thicknesses on the hydrophobicity of the silica coatings have been analysed. The morphology, chemical composition, thermal degradation and hydrophobicity of the resulting surfaces have been studied by scanning electron microscopy (SEM), Fourier transfer infrared spectrometer (FT-IR), Thermogravimetry (TGA) and water contact angle (WCA) measurement. The results show that an average water contact angle of 149° after been cured at 400 °C for a coating aged for 5 days, and four deposition cycles using a dipping rate of 1000 mm/min was achieved.

scholarly journals Experimental approach towards the water contact angle value on the biomaterial alloy Ti6Al4V

2015 ◽  
Vol 70 (1) ◽  
pp. 1-13 ◽  
Author(s):  
Margarita Hierro-Oliva ◽  
Amparo Maria Gallardo-Moreno ◽  
Abraham Rodríguez-Cano ◽  
Jose Morales Bruque ◽  
Maria Luisa González-Martín
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Contact Angles ◽  
Ti6al4v Alloy ◽  
Surrounding Water ◽  
Water Contact ◽  
Large Dispersion ◽  
Biomaterial Surface ◽  
Average Water ◽  
Orthopedic Applications

AbstractIn the biomedical field, water contact angle is a useful gauge to follow how a biomaterial surface would interact with the surrounding water-like physiological environment. Ti6Al4V alloy is widely used in orthopedic applications. Nevertheless, the values of its water contact angle reported in the literature show a large dispersion, from 40° up 80°. However, in addition to the expected dependence of the surface wettability on preliminary treatments, the values of the water contact angle on the pristine Ti6Al4V alloy suffers from an important variability and lack of reproducibility. The present research pays attention to this difficulty and proposes a simple experimental procedure to ensure adequate contact angle reproducibility. Controlled passivation growth in mild underwater conditions of freshly polished disks, followed by ultrasonic washing, avoiding the rubbing of the surface, gives average water contact angles of 80° with very low standard deviations also among samples from the same batch.

Modification of Mg Alloy Surfaces Based on Micro-Arc Oxidation Methods

2014 ◽  
Vol 905 ◽  
pp. 146-150 ◽  
Author(s):  
Hong Tao ◽  
So King Ho ◽  
Echo Li ◽  
Xue Zhu Zhang ◽  
Gary Lai
Keyword(s):  
Electrical Conductivity ◽  
Contact Angle ◽  
Protective Coatings ◽  
Xrd Analysis ◽  
Water Contact ◽  
Nanoscale Structures ◽  
Oxidation Processes ◽  
Micro Arc Oxidation ◽  
Phase And Chemical Composition ◽  
Made In

Chemically and mechanically protective coatings are formed on surface of Magnesium alloys by micro-arc oxidation (MAO) methods. Modification of the obtained MAO surfaces was made in two aspects. Firstly, the protection is enhanced by forming super-hydrophobic surfaces, with water contact angle higher than 120o, attributed to hierarchical nanomicro structures. The overall process involves alkaline etching to form nanoscale structures on top of micro-porous surface achieved during micro-arc oxidation processes. Secondly, the electrical property of the MAO surfaces is modified. A film with electrical conductivity of 2.4Ω/sq is achieved by Ni deposition and characterized by four point probe measurement. The morphology, phase, and chemical composition of all surfaces are investigated by SEM, AFM, and XRD analysis.

scholarly journals Design of SiO2/TiO2 that Synergistically Increases The Hydrophobicity of Methyltrimethoxysilane Coated Glass

2019 ◽  
Vol 17 (1) ◽  
pp. 798-805 ◽  
Author(s):  
Alfa Akustia Widati ◽  
Nuryono Nuryono ◽  
Indriana Kartini
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Water Contact Angle ◽  
Research Work ◽  
Dip Coating ◽  
Layer By Layer ◽  
Titanium Tetraisopropoxide ◽  
Water Contact ◽  
Nanoscale Structures ◽  
Coated Glass

AbstractThis research work presents the design of a mixture of SiO2/TiO2 that increases the surface roughness and hydrophobicity of methyltrimethoxysilane (MTMS) coated glass. The deposition of SiO2, TiO2, and MTMS were conducted using a layer by layer dip coating technique. The SiO2/TiO2 coating was derived from complete hydrolysis of tetraethylorthsilicate and titanium tetraisopropoxide. In order to evaluate and compare the performance of SiO2/TiO2/MTMS coated glass, the SiO2/SiO2/MTMS and TiO2/TiO2/MTMS were also fabricated. SiO2/TiO2/MTMS samples displayed the highest water contact angle. The topography of surfaces showed that SiO2/TiO2/MTMS exposed higher surface roughness with micro-nanoscale structures. The sequence of SiO2 and TiO2 influenced the water contact angle and the stability of the coatings. SiO2/TiO2/MTMS produced higher contact angle and stability than TiO2/SiO2/MTMS.

Long-Term Stable Metal Organic Framework (MOF) Based Mixed Matrix Membranes for Ultrafiltration

2020 ◽  
Author(s):  
Muayad Al-shaeli ◽  
Stefan J. D. Smith ◽  
Shanxue Jiang ◽  
Huanting Wang ◽  
Kaisong Zhang ◽  
...  
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Mixed Matrix Membranes ◽  
Recovery Ratio ◽  
Mixed Matrix ◽  
Water Contact ◽  
Membrane Performance ◽  
Metal Organic ◽  
Matrix Membranes

<p>In this study, novel <a>mixed matrix polyethersulfone (PES) membranes</a> were synthesized by using two different kinds of metal organic frameworks (MOFs), namely UiO-66 and UiO-66-NH<sub>2</sub>. The composite membranes were characterised by SEM, EDX, FTIR, PXRD, water contact angle, porosity, pore size, etc. Membrane performance was investigated by water permeation flux, flux recovery ratio, fouling resistance and anti-fouling performance. The stability test was also conducted for the prepared mixed matrix membranes. A higher reduction in the water contact angle was observed after adding both MOFs to the PES and sulfonated PES membranes compared to pristine PES membranes. An enhancement in membrane performance was observed by embedding the MOF into PES membrane matrix, which may be attributed to the super-hydrophilic porous structure of UiO-66-NH<sub>2</sub> nanoparticles and hydrophilic structure of UiO-66 nanoparticles that could accelerate the exchange rate between solvent and non-solvent during the phase inversion process. By adding the MOFs into PES matrix, the flux recovery ratio was increased greatly (more than 99% for most mixed matrix membranes). The mixed matrix membranes showed higher resistance to protein adsorption compared to pristine PES membranes. After immersing the membranes in water for 3 months, 6 months and 12 months, both MOFs were stable and retained their structure. This study indicates that UiO-66 and UiO-66-NH<sub>2</sub> are great candidates for designing long-term stable mixed matrix membranes with higher anti-fouling performance.</p>

scholarly journals Surface modification of PMMA polymer and its composites with PC61BM fullerene derivative using an atmospheric pressure microwave argon plasma sheet

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Andrzej Sikora ◽  
Dariusz Czylkowski ◽  
Bartosz Hrycak ◽  
Magdalena Moczała-Dusanowska ◽  
Marcin Łapiński ◽  
...  
Keyword(s):  
Contact Angle ◽  
Surface Modification ◽  
Chemical Composition ◽  
Water Contact Angle ◽  
Plasma Sheet ◽  
Atmospheric Pressure ◽  
Argon Plasma ◽  
Fullerene Derivative ◽  
Water Contact ◽  
Pmma Polymer

AbstractThis paper presents the results of experimental investigations of the plasma surface modification of a poly(methyl methacrylate) (PMMA) polymer and PMMA composites with a [6,6]-phenyl-C61-butyric acid methyl ester fullerene derivative (PC61BM). An atmospheric pressure microwave (2.45 GHz) argon plasma sheet was used. The experimental parameters were: an argon (Ar) flow rate (up to 20 NL/min), microwave power (up to 530 W), number of plasma scans (up to 3) and, the kind of treated material. In order to assess the plasma effect, the possible changes in the wettability, roughness, chemical composition, and mechanical properties of the plasma-treated samples’ surfaces were evaluated by water contact angle goniometry (WCA), atomic force microscopy (AFM), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS). The best result concerning the water contact angle reduction was from 83° to 29.7° for the PMMA material. The ageing studies of the PMMA plasma-modified surface showed long term (100 h) improved wettability. As a result of plasma treating, changes in the samples surface roughness parameters were observed, however their dependence on the number of plasma scans is irregular. The ATR-FTIR spectra of the PMMA plasma-treated surfaces showed only slight changes in comparison with the spectra of an untreated sample. The more significant differences were demonstrated by XPS measurements indicating the surface chemical composition changes after plasma treatment and revealing the oxygen to carbon ratio increase from 0.1 to 0.4.

scholarly journals Physicochemical Properties and Biocompatibility of Electrospun Polycaprolactone/Gelatin Nanofibers

2021 ◽  
Vol 18 (9) ◽  
pp. 4764
Author(s):  
Wei Lee Lim ◽  
Shiplu Roy Chowdhury ◽  
Min Hwei Ng ◽  
Jia Xian Law
Keyword(s):  
Contact Angle ◽  
Physicochemical Properties ◽  
Water Contact Angle ◽  
Ligament Injury ◽  
Great Promise ◽  
Composition Analysis ◽  
Water Contact ◽  
Tenogenic Differentiation ◽  
Good Biocompatibility ◽  
Tissue Grafts

Tissue-engineered substitutes have shown great promise as a potential replacement for current tissue grafts to treat tendon/ligament injury. Herein, we have fabricated aligned polycaprolactone (PCL) and gelatin (GT) nanofibers and further evaluated their physicochemical properties and biocompatibility. PCL and GT were mixed at a ratio of 100:0, 70:30, 50:50, 30:70, 0:100, and electrospun to generate aligned nanofibers. The PCL/GT nanofibers were assessed to determine the diameter, alignment, water contact angle, degradation, and surface chemical analysis. The effects on cells were evaluated through Wharton’s jelly-derived mesenchymal stem cell (WJ-MSC) viability, alignment and tenogenic differentiation. The PCL/GT nanofibers were aligned and had a mean fiber diameter within 200–800 nm. Increasing the GT concentration reduced the water contact angle of the nanofibers. GT nanofibers alone degraded fastest, observed only within 2 days. Chemical composition analysis confirmed the presence of PCL and GT in the nanofibers. The WJ-MSCs were aligned and remained viable after 7 days with the PCL/GT nanofibers. Additionally, the PCL/GT nanofibers supported tenogenic differentiation of WJ-MSCs. The fabricated PCL/GT nanofibers have a diameter that closely resembles the native tissue’s collagen fibrils and have good biocompatibility. Thus, our study demonstrated the suitability of PCL/GT nanofibers for tendon/ligament tissue engineering applications.

Sign in / Sign up

Export Citation Format

Share Document