scholarly journals A Novel Universal Approach for Temperature Correction on Frequency Domain Spectroscopy Curve of Transformer Polymer Insulation

Polymers ◽  
2019 ◽  
Vol 11 (7) ◽  
pp. 1126 ◽  
Author(s):  
Jiefeng Liu ◽  
Xianhao Fan ◽  
Yiyi Zhang ◽  
Hanbo Zheng ◽  
Huilu Yao ◽  
...  
Keyword(s):  
Frequency Domain ◽  
Master Curve ◽  
Shift Factor ◽  
Temperature Correction ◽  
Universal Method ◽  
Temperature Dependent ◽  
Universal Approach ◽  
Different Types ◽  
Different Temperatures ◽  
The Difference

It is a fact that the frequency domain spectroscopy (FDS) curve at different temperatures can be corrected by the shift factor (αT) extracted from the master curve. However, the αT and master curve reported by previous works are distinctive due to the difference in the construction algorithm. Therefore, it is of great significance to report a universal approach for extracting αT. In this work, the unaged oil-immersed pressboards with different moisture content (mc%) are firstly prepared and selected as the research specimen. Then, the αT of FDS curves on the above pressboard is extracted based upon the master curve technique. The influence mechanism under the various test temperature (T) and mc% is therefore analyzed so as to establish a universal model for predicting the αT. The present findings reveal that the αT value extracted from FDS curves is both temperature-dependent and moisture-dependent. In addition, the predicted αT is not only suitable for temperature correction on FDS curve of same type pressboard with different insulation conditions (moisture contents and aging degrees), but also maintains considerable accuracy when applied to different types of pressboard. Therefore, the obtained conclusions will provide a universal method for temperature correction on FDS curve of transformer polymer insulation.

Uniaxial Wave Propagation in a Viscoelastic Material Using Measured Material Properties

1968 ◽  
Vol 35 (3) ◽  
pp. 449-453 ◽  
Author(s):  
W. G. Knauss
Keyword(s):  
Wave Propagation ◽  
Viscoelastic Material ◽  
Material Properties ◽  
Material Characterization ◽  
Wave Speed ◽  
Initial Temperature ◽  
Initial Step ◽  
Shift Factor ◽  
Temperature Dependent ◽  
The Difference

The dynamic response of a long viscoelastic bar due to a step displacement at the end is considered. Neglecting geometric dispersion, the effect of realistic viscoelastic material properties is studied theoretically. The solution is obtained in the form of a Fourier sine integral, the convergence of which is studied numerically by piecewise integration to produce an alternating series. It is found that the initial step wave propagates with a high velocity corresponding to the glassy modulus of the material and its amplitude decays with time and distance along the rod. From a practical viewpoint the wave front may decay to immeasurable proportions and any measurable disturbance appears to travel thereafter, with a velocity which is smaller than the glassy wave speed. The effect of initial temperature is discussed. It is shown for thermorheologically simple materials that both the time and spatial variable are scaled by the same temperature dependent (shift) factor. As a consequence, the difference of wave propagation in hard and viscoelastic polymers is illustrated. It is also shown that limited material characterization is sufficient for certain dynamic problems. Comparison of the exact solution with two approximations is made.

scholarly journals Correction for Polarization Current Curve of Polymer Insulation Materials in Transformers Considering the Temperature and Moisture Effects

Polymers ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 143 ◽  
Author(s):  
Hanbo Zheng ◽  
Benhui Lai ◽  
Yiyi Zhang ◽  
Jiefeng Liu ◽  
Shichang Yang
Keyword(s):  
Moisture Content ◽  
Functional Relationship ◽  
Shift Factor ◽  
Temperature Correction ◽  
Polarization Current ◽  
Correction Model ◽  
Moisture Effects ◽  
Current Curve ◽  
Different Temperatures ◽  
Cellulose Insulation

Depending on the study of the master curve technique, a temperature correction model for the polarization current of transformer polymer (cellulose) insulation, considering the effects of both moisture content (mc%) and temperature is proposed. In the current work, the shift factors of polarization current curves of samples with various moisture contents are extracted at different temperatures. Then, the variation law among the shift factor, test temperature, and moisture content are studied so as to establish the corresponding functional relationship. The findings reveal that the modified model derived from the above functional relationship could be employed to perform the temperature correction of oil-immersed polymer samples with various insulation states. Therefore, the proposed temperature correction model in this paper will promote the state assessment of the field transformer polymer insulation.

Temperature-Dependent Logic Failure in a GaAs Power Amplifier-Duplexer Module Caused by a Subtle Parasitic Schottky Diode

2014 ◽  
Author(s):  
Rose Emergo ◽  
Steve Brockett ◽  
Pat Hamilton
Keyword(s):  
Power Amplifier ◽  
Schottky Diode ◽  
Production Test ◽  
Temperature Dependent ◽  
Cold Temperatures ◽  
Collector Junction ◽  
Power Mode ◽  
The Difference ◽  
Base Contact ◽  
Single Power

Abstract A single power amplifier-duplexer device was submitted by a customer for analysis. The device was initially considered passing when tested against the production test. However, further electrical testing suggested that the device was stuck in a single power mode for a particular frequency band at cold temperatures only. This paper outlines the systematic isolation of a parasitic Schottky diode formed by a base contactcollector punch through process defect that pulled down the input of a NOR gate leading to the incorrect logic state. Note that this parasitic Schottky diode is parallel to the basecollector junction. It was observed that the logic failure only manifested at colder temperatures because the base contact only slightly diffused into the collector layer. Since the difference in the turn-on voltages between the base-collector junction and the parasitic Schottky diode increases with decreasing temperature, the effect of the parasitic diode is only noticeable at lower temperatures.

scholarly journals GERMINATION AND VIGOUR IN SEEDS OF THE COWPEA IN RESPONSE TO SALT AND HEAT STRESS

2019 ◽  
Vol 32 (1) ◽  
pp. 143-151 ◽  
Author(s):  
Luma Rayane de Lima Nunes ◽  
Paloma Rayane Pinheiro ◽  
Charles Lobo Pinheiro ◽  
Kelly Andressa Peres Lima ◽  
Alek Sandro Dutra
Keyword(s):  
Salt Stress ◽  
Heat Stress ◽  
High Temperature ◽  
Low Temperature ◽  
Vigna Unguiculata ◽  
Salt Concentration ◽  
Dry Weight ◽  
Germination Percentage ◽  
Different Types ◽  
Different Temperatures

ABSTRACT Salinity is prejudicial to plant development, causing different types of damage to species, or even between genotypes of the same species, with the effects being aggravated when combined with other types of stress, such as heat stress. The aim of this study was to evaluate the tolerance of cowpea genotypes (Vigna unguiculata L. Walp.) to salt stress at different temperatures. Seeds of the Pujante, Epace 10 and Marataoã genotypes were placed on paper rolls (Germitest®) moistened with different salt concentrations of 0.0 (control), 1.5, 3.0, 4.5 and 6.0 dS m-1, and placed in a germination chamber (BOD) at temperatures of 20, 25, 30 and 35°C. The experiment was conducted in a completely randomised design, in a 3 × 4 × 5 scheme of subdivided plots, with four replications per treatment. The variables under analysis were germination percentage, first germination count, shoot and root length, and total seedling dry weight. At temperatures of 30 and 35°C, increases in the salt concentration were more damaging to germination in the Epace 10 and Pujante genotypes, while for the Marataoã genotype, damage occurred at the temperature of 20°C. At 25°C, germination and vigour in the genotypes were higher, with the Pujante genotype proving to be more tolerant to salt stress, whereas Epace 10 and Marataoã were more tolerant to high temperatures. Germination in the cowpea genotypes was more sensitive to salt stress when subjected to heat stress caused by the low temperature of 20°C or high temperature of 35°C.

scholarly journals The Respiration of some Planktonic copepods II. The Effect Of Temperature

1953 ◽  
Vol 31 (3) ◽  
pp. 447-460 ◽  
Author(s):  
D. T. Gauld ◽  
J. E. G. Raymont
Keyword(s):  
Respiratory Rate ◽  
The Body ◽  
The Other ◽  
Effect Of Temperature ◽  
Acartia Clausi ◽  
Temora Longicornis ◽  
Different Temperatures ◽  
Planktonic Copepods ◽  
The Difference ◽  
The Relationship

The respiratory rates of three species of planktonic copepods, Acartia clausi, Centropages hamatus and Temora longicornis, were measured at four different temperatures.The relationship between respiratory rate and temperature was found to be similar to that previously found for Calanus, although the slope of the curves differed in the different species.The observations on Centropages at 13 and 170 C. can be divided into two groups and it is suggested that the differences are due to the use of copepods from two different generations.The relationship between the respiratory rates and lengths of Acartia and Centropages agreed very well with that previously found for other species. That for Temora was rather different: the difference is probably due to the distinct difference in the shape of the body of Temora from those of the other species.The application of these measurements to estimates of the food requirements of the copepods is discussed.

Investigation of Dielectric Properties of TiO2 and Al2O3 nanofluids by Frequency Domain Spectroscopy at Different Temperatures

2021 ◽  
Vol 330 ◽  
pp. 115642
Author(s):  
B. Chakraborty ◽  
K.Y. Raj ◽  
A.K. Pradhan ◽  
B. Chatterjee ◽  
S. Chakravorti ◽  
...  
Keyword(s):  
Dielectric Properties ◽  
Frequency Domain ◽  
Different Temperatures

scholarly journals Investigation of Color Reproduction on Linen Fabrics when Printing with Mimaki TX400-1800D Inkjet with Pigment TP250 Dyes

Coatings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 354
Author(s):  
Tim Tofan ◽  
Rimantas Stonkus ◽  
Raimondas Jasevičius
Keyword(s):  
Mechanical Properties ◽  
Color Reproduction ◽  
Related Effect ◽  
Color Characteristics ◽  
Fabric Density ◽  
Different Types ◽  
The Difference ◽  
Printing Parameters ◽  
Linen Fabric

The aim of this research is to investigate related effect of dyeability to linen textiles related to different printing parameters. The study investigated the change in color characteristics when printing on linen fabrics with an inkjet MIMAKI Tx400-1800D printer with pigmented TP 250 inks. The dependence of color reproduction on linen fabrics on the number of print head passes, number of ink layers to be coated, linen fabric density, and different types of linen fabric was investigated. All this affects the quality of print and its mechanical properties. The change in color characteristics on different types of linen fabrics was determined experimentally. We determine at which print settings the most accurate color reproduction can be achieved on different linen fabrics. The difference between the highest and the lowest possible number of head passages was investigated. The possibilities of reproducing different linen fabric colors were determined.

Recent advances in synthesis of organometallic complexes of indium

2020 ◽  
Vol 40 (3) ◽  
pp. 107-151
Author(s):  
Hira Anwar ◽  
Rosenani A. Haque ◽  
Rahman Shah Zaib Saleem ◽  
Muhammad Adnan Iqbal
Keyword(s):  
Material Science ◽  
Thin Film Transistors ◽  
Heterocyclic Carbenes ◽  
Organometallic Complexes ◽  
Organic Ligands ◽  
Group 13 ◽  
Indium Complexes ◽  
Different Types ◽  
Stirring Time ◽  
Different Temperatures

AbstractThe indium complexes are being used in many applications like catalysis, optoelectronics, sensors, solar cells, biochemistry, medicine, infrared (IR) mirrors and thin-film transistors (TFTs). In organometallic complexes of indium, it forms different types of complexes with single, double, triple and tetra linkages by coordinating with numerous elements like C, N, O and S and also with some other elements like Se and Ru. So, the present study comprises all the possible ways to synthesize the indium complexes by reacting with different organic ligands; most of them are N-heterocyclic carbenes, amines, amides and phenols. The commonly used solvents for these syntheses are tetrahydrofuran, dichloromethane, toluene, benzene, dimethyl sulfoxide (DMSO) and water. According to the nature of the ligands, indium complexes were reported at different temperatures and stirring time. Because of their unique characteristics, the organometallic chemistry of group 13 metal indium complexes remains a subject of continuing interest in synthetic chemistry as well as material science.

scholarly journals Action and Entropy in Heat Engines: An Action Revision of the Carnot Cycle

Entropy ◽  
2021 ◽  
Vol 23 (7) ◽  
pp. 860
Author(s):  
Ivan R. Kennedy ◽  
Migdat Hodzic
Keyword(s):  
Heat Engine ◽  
Working Fluid ◽  
Field Energy ◽  
Carnot Cycle ◽  
Gibbs Potential ◽  
Atmospheric Gases ◽  
Temperature Dependent ◽  
Expansion Phase ◽  
Heat Engines ◽  
The Difference

Despite the remarkable success of Carnot’s heat engine cycle in founding the discipline of thermodynamics two centuries ago, false viewpoints of his use of the caloric theory in the cycle linger, limiting his legacy. An action revision of the Carnot cycle can correct this, showing that the heat flow powering external mechanical work is compensated internally with configurational changes in the thermodynamic or Gibbs potential of the working fluid, differing in each stage of the cycle quantified by Carnot as caloric. Action (@) is a property of state having the same physical dimensions as angular momentum (mrv = mr2ω). However, this property is scalar rather than vectorial, including a dimensionless phase angle (@ = mr2ωδφ). We have recently confirmed with atmospheric gases that their entropy is a logarithmic function of the relative vibrational, rotational, and translational action ratios with Planck’s quantum of action ħ. The Carnot principle shows that the maximum rate of work (puissance motrice) possible from the reversible cycle is controlled by the difference in temperature of the hot source and the cold sink: the colder the better. This temperature difference between the source and the sink also controls the isothermal variations of the Gibbs potential of the working fluid, which Carnot identified as reversible temperature-dependent but unequal caloric exchanges. Importantly, the engine’s inertia ensures that heat from work performed adiabatically in the expansion phase is all restored to the working fluid during the adiabatic recompression, less the net work performed. This allows both the energy and the thermodynamic potential to return to the same values at the beginning of each cycle, which is a point strongly emphasized by Carnot. Our action revision equates Carnot’s calorique, or the non-sensible heat later described by Clausius as ‘work-heat’, exclusively to negative Gibbs energy (−G) or quantum field energy. This action field complements the sensible energy or vis-viva heat as molecular kinetic motion, and its recognition should have significance for designing more efficient heat engines or better understanding of the heat engine powering the Earth’s climates.

Sign in / Sign up

Export Citation Format

Share Document