scholarly journals Additive Manufacturing of PLA-Based Composites Using Fused Filament Fabrication: Effect of Graphene Nanoplatelet Reinforcement on Mechanical Properties, Dimensional Accuracy and Texture

Polymers ◽  
2019 ◽  
Vol 11 (5) ◽  
pp. 799 ◽  
Author(s):  
Miguel Caminero ◽  
Jesús Chacón ◽  
Eustaquio García-Plaza ◽  
Pedro Núñez ◽  
José Reverte ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Impact Strength ◽  
Dimensional Accuracy ◽  
Fused Filament Fabrication ◽  
Graphene Nanoplatelet ◽  
Graphene Composite ◽  
General Terms ◽  
3D Printed ◽  
Composite Samples

Fused filament fabrication (FFF) is a promising additive manufacturing (AM) technology due to its ability to build thermoplastics parts with advantages in the design and optimization of models with complex geometries, great design flexibility, recyclability and low material waste. This technique has been extensively used for the manufacturing of conceptual prototypes rather than functional components due to the limited mechanical properties of pure thermoplastics parts. In order to improve the mechanical performance of 3D printed parts based on polymeric materials, reinforcements including nanoparticles, short or continuous fibers and other additives have been adopted. The addition of graphene nanoplatelets (GNPs) to plastic and polymers is currently under investigation as a promising method to improve their working conditions due to the good mechanical, electrical and thermal performance exhibited by graphene. Although research shows particularly promising improvement in thermal and electrical conductivities of graphene-based nanocomposites, the aim of this study is to evaluate the effect of graphene nanoplatelet reinforcement on the mechanical properties, dimensional accuracy and surface texture of 3D printed polylactic acid (PLA) structures manufactured by a desktop 3D printer. The effect of build orientation was also analyzed. Scanning Electron Microscope (SEM) images of failure samples were evaluated to determine the effects of process parameters on failure modes. It was observed that PLA-Graphene composite samples showed, in general terms, the best performance in terms of tensile and flexural stress, particularly in the case of upright orientation (about 1.5 and 1.7 times higher than PLA and PLA 3D850 samples, respectively). In addition, PLA-Graphene composite samples showed the highest interlaminar shear strength (about 1.2 times higher than PLA and PLA 3D850 samples). However, the addition of GNPs tended to reduce the impact strength of the PLA-Graphene composite samples (PLA and PLA 3D850 samples exhibited an impact strength about 1.2–1.3 times higher than PLA-Graphene composites). Furthermore, the addition of graphene nanoplatelets did not affect, in general terms, the dimensional accuracy of the PLA-Graphene composite specimens. In addition, PLA-Graphene composite samples showed, in overall terms, the best performance in terms of surface texture, particularly when parts were printed in flat and on-edge orientations. The promising results in the present study prove the feasibility of 3D printed PLA-graphene composites for potential use in different applications such as biomedical engineering.

scholarly journals Additive Manufacturing of Bone Scaffolds Using PolyJet and Stereolithography Techniques

2021 ◽  
Vol 11 (16) ◽  
pp. 7336
Author(s):  
Shummaila Rasheed ◽  
Waqas Akbar Lughmani ◽  
Muhannad Ahmed Obeidi ◽  
Dermot Brabazon ◽  
Inam Ul Ahad
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Dimensional Accuracy ◽  
Human Bone ◽  
Compression Tests ◽  
3D Scaffold ◽  
Bone Scaffolds ◽  
3D Printed ◽  
Printing Direction ◽  
Printing Techniques

In this study, the printing capability of two different additive manufacturing (3D printing) techniques, namely PolyJet and micro-stereolithography (µSLA), are investigated regarding the fabrication of bone scaffolds. The 3D-printed scaffold structures are used as supports in replacing and repairing fractured bone tissue. Printed bone scaffolds with complex structures produced using additive manufacturing technology can mimic the mechanical properties of natural human bone, providing lightweight structures with modifiable porosity levels. In this study, 3D scaffold structures are designed with different combinations of architectural parameters. The dimensional accuracy, permeability, and mechanical properties of complex 3D-printed scaffold structures are analyzed to compare the advantages and drawbacks associated with the two techniques. The fluid flow rates through the 3D-printed scaffold structures are measured and Darcy’s law is applied to calculate the experimentally measured permeability. The Kozeny–Carman equation is applied for theoretical calculation of permeability. Compression tests were performed on the printed samples to observe the effects of the printing techniques on the mechanical properties of the 3D-printed scaffold structures. The effect of the printing direction on the mechanical properties of the 3D-printed scaffold structures is also analyzed. The scaffold structures printed with the µSLA printer demonstrate higher permeability and mechanical properties as compared to those printed using the PolyJet technique. It is demonstrated that both the µSLA and PolyJet printing techniques can be used to print 3D scaffold structures with controlled porosity levels, providing permeability in a similar range to human bone.

scholarly journals Effect of Porosity and Crystallinity on 3D Printed PLA Properties

Polymers ◽  
2019 ◽  
Vol 11 (9) ◽  
pp. 1487 ◽  
Author(s):  
Yuhan Liao ◽  
Chang Liu ◽  
Bartolomeo Coppola ◽  
Giuseppina Barra ◽  
Luciano Di Maio ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Polylactic Acid ◽  
Complex Geometry ◽  
Fused Filament Fabrication ◽  
3D Printed ◽  
Physical Changes ◽  
Crystalline Forms

Additive manufacturing (AM) is a promising technology for the rapid tooling and fabrication of complex geometry components. Among all AM techniques, fused filament fabrication (FFF) is the most widely used technique for polymers. However, the consistency and properties control of the FFF product remains a challenging issue. This study aims to investigate physical changes during the 3D printing of polylactic acid (PLA). The correlations between the porosity, crystallinity and mechanical properties of the printed parts were studied. Moreover, the effects of the build-platform temperature were investigated. The experimental results confirmed the anisotropy of printed objects due to the occurrence of orientation phenomena during the filament deposition and the formation both of ordered and disordered crystalline forms (α and δ, respectively). A heat treatment post-3D printing was proposed as an effective method to improve mechanical properties by optimizing the crystallinity (transforming the δ form into the α one) and overcoming the anisotropy of the 3D printed object.

scholarly journals Dimensional Accuracy and Mechanical Properties of Chopped Carbon Reinforced Polymers Produced by Material Extrusion Additive Manufacturing

Materials ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 3885 ◽  
Author(s):  
Evren Yasa ◽  
Kıvılcım Ersoy
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Modulus Of Elasticity ◽  
High Speed ◽  
Polymer Matrix Composites ◽  
Low Cost ◽  
Dimensional Accuracy ◽  
Fused Filament Fabrication ◽  
Material Extrusion ◽  
Pull Out

Fused Filament Fabrication (FFF), classified under material extrusion additive manufacturing technologies, is a widely used method for fabricating thermoplastic parts with high geometrical complexity. To improve the mechanical properties of pure thermoplastic materials, the polymeric matrix may be reinforced by different materials such as carbon fibers. FFF is an advantageous process for producing polymer matrix composites because of its low cost of investment, high speed and simplicity as well as the possibility to use multiple nozzles with different materials. In this study, the aim was to investigate the dimensional accuracy and mechanical properties of chopped carbon-fiber-reinforced tough nylon produced by the FFF process. The dimensional accuracy and manufacturability limits of the process are evaluated using benchmark geometries as well as process-inherent effects like stair-stepping effect. The hardness and tensile properties of produced specimens in comparison to tough nylon without any reinforcement, as well as continuous carbon-reinforced specimens, were presented by taking different build directions and various infill ratios. The fracture surfaces of tensile specimens were observed using a Scanning Electron Microscope (SEM). The test results showed that there was a severe level of anisotropy in the mechanical properties, especially the modulus of elasticity, due to the insufficient fusion between deposited layers in the build direction. Moreover, continuous carbon-reinforced specimens exhibited very high levels of tensile strength and modulus of elasticity whereas the highest elongation was achieved by tough nylon without reinforcement. The failure mechanisms were found to be inter-layer porosity between successive tracks, as well as fiber pull out.

Effect of nozzle diameter on mechanical and geometric performance of 3D printed carbon fibre-reinforced composites manufactured by fused filament fabrication

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Jesús Miguel Chacón ◽  
Miguel Ángel Caminero ◽  
Pedro José Núñez ◽  
Eustaquio García-Plaza ◽  
Jean Paul Bécar
Keyword(s):  
Surface Roughness ◽  
Carbon Fibre ◽  
Mechanical Performance ◽  
Dimensional Accuracy ◽  
Nozzle Diameter ◽  
Fused Filament Fabrication ◽  
Manufacturing Costs ◽  
Content Type ◽  
3D Printed ◽  
Composite Samples

Purpose Fused filament fabrication (FFF) is one of the most popular additive manufacturing (AM) technologies due to its ability to build thermoplastic parts with complex geometries at low cost. The FFF technique has been mainly used for rapid prototyping owing to the poor mechanical and geometrical properties of pure thermoplastic parts. However, both the development of new fibre-reinforced filaments with improved mechanical properties, and more accurate composite 3D printers have broadened the scope of FFF applications to functional components. FFF is a complex process with a large number of parameters influencing product quality and mechanical properties, and the effects of the combined parameters are usually difficult to evaluate. An array of parameter combinations has been analysed for improving the mechanical performance of thermoplastic parts such as layer thickness, build orientation, raster angle, raster width, air gap, infill density and pattern, fibre volume fraction, fibre layer location, fibre orientation and feed rate. This study aims to assess the effects of nozzle diameter on the mechanical performance and the geometric properties of 3D printed short carbon fibre-reinforced composites processed by the FFF technique. Design methodology approach Tensile and three-point bending tests were performed to characterise the mechanical response of the 3D printed composite samples. The dimensional accuracy, the flatness error and surface roughness of the printed specimens were also evaluated. Moreover, manufacturing costs, which are related to printing time, were evaluated. Finally, scanning electron microscopy images of the printed samples were analysed to estimate the porosity as a function of the nozzle diameter and to justify the effect of nozzle diameter on dimensional accuracy and surface roughness. Findings The effect of nozzle diameter on the mechanical and geometric quality of 3D printed composite samples was significant. In addition, large nozzle diameters tended to increase mechanical performance and enhance surface roughness, with a reduction in manufacturing costs. In contrast, 3D printed composite samples with small nozzle diameter exhibited higher geometric accuracy. However, the effect of nozzle diameter on the flatness error and surface roughness was of slight significance. Finally, some print guidelines are included. Originality value The effect of nozzle diameter, which is directly related to product quality and manufacturing costs, has not been extensively studied. The presented study provides more information regarding the dependence of the mechanical, microstructural and geometric properties of short carbon fibre-reinforced nylon composite components on nozzle diameter.

Fused Filament Fabrication 3D Printed Polylactic Acid Electroosmotic Pumps

Lab on a Chip ◽  
2021 ◽  
Author(s):  
Liang Wu ◽  
Stephen Beirne ◽  
Joan-Marc Cabot Canyelles ◽  
Brett Paull ◽  
Gordon G. Wallace ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
3D Printing ◽  
Polylactic Acid ◽  
Fused Filament Fabrication ◽  
Flexible Approach ◽  
Electroosmotic Pump ◽  
3D Printed ◽  
Electroosmotic Pumps

Additive manufacturing (3D printing) offers a flexible approach for the production of bespoke microfluidic structures such as the electroosmotic pump. Here a readily accessible fused filament fabrication (FFF) 3D printing...

Mechanical Properties of 3D-Printed Wood-Plastic Composites

2018 ◽  
Vol 777 ◽  
pp. 499-507 ◽  
Author(s):  
Ossi Martikka ◽  
Timo Kärki ◽  
Qing Ling Wu
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
3D Printing ◽  
Impact Strength ◽  
Polylactic Acid ◽  
Wood Plastic Composite ◽  
Wood Plastic Composites ◽  
Plastic Composite ◽  
Plastic Composites ◽  
3D Printed

3D printing has rapidly become popular in both industry and private use. Especially fused deposition modeling has increased its popularity due to its relatively low cost. The purpose of this study is to increase knowledge in the mechanical properties of parts made of wood-plastic composite materials by using 3D printing. The tensile properties and impact strength of two 3D-printed commercial wood-plastic composite materials are studied and compared to those made of pure polylactic acid. Relative to weight –mechanical properties and the effect of the amount of fill on the properties are also determined. The results indicate that parts made of wood-plastic composites have notably lower tensile strength and impact strength that those made of pure polylactic acid. The mechanical properties can be considered sufficient for low-stress applications, such as visualization of prototypes and models or decorative items.

scholarly journals Effect of Porosity on Mechanical Properties of 3D Printed Polymers: Experiments and Micromechanical Modeling Based on X-Ray Computed Tomography Analysis

Polymers ◽  
2019 ◽  
Vol 11 (7) ◽  
pp. 1154 ◽  
Author(s):  
Wang ◽  
Zhao ◽  
Fuh ◽  
Lee
Keyword(s):  
Computed Tomography ◽  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Fused Deposition Modeling ◽  
Micromechanical Model ◽  
Micromechanical Modeling ◽  
X Ray ◽  
Fused Deposition ◽  
3D Printed ◽  
X Ray Computed

Additive manufacturing (commonly known as 3D printing) is defined as a family of technologies that deposit and consolidate materials to create a 3D object as opposed to subtractive manufacturing methodologies. Fused deposition modeling (FDM), one of the most popular additive manufacturing techniques, has demonstrated extensive applications in various industries such as medical prosthetics, automotive, and aeronautics. As a thermal process, FDM may introduce internal voids and pores into the fabricated thermoplastics, giving rise to potential reduction on the mechanical properties. This paper aims to investigate the effects of the microscopic pores on the mechanical properties of material fabricated by the FDM process via experiments and micromechanical modeling. More specifically, the three-dimensional microscopic details of the internal pores, such as size, shape, density, and spatial location were quantitatively characterized by X-ray computed tomography (XCT) and, subsequently, experiments were conducted to characterize the mechanical properties of the material. Based on the microscopic details of the pores characterized by XCT, a micromechanical model was proposed to predict the mechanical properties of the material as a function of the porosity (ratio of total volume of the pores over total volume of the material). The prediction results of the mechanical properties were found to be in agreement with the experimental data as well as the existing works. The proposed micromechanical model allows the future designers to predict the elastic properties of the 3D printed material based on the porosity from XCT results. This provides a possibility of saving the experimental cost on destructive testing.

scholarly journals EFFECT OF EXTRUSION PROCESS PARAMETERS ON MECHANICAL PROPERTIES OF 3D PRINTED PLA PRODUCT

2021 ◽  
Vol 6 (2) ◽  
pp. 119
Author(s):  
Nanang Ali Sutisna ◽  
Rakha Amrillah Fattah
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Fused Deposition Modeling ◽  
Extrusion Process ◽  
Experimental Procedure ◽  
Fused Deposition ◽  
Novel Approach ◽  
Deposition Modeling ◽  
3D Printed ◽  
3D Digital Models

The method of producing items through synchronously depositing material level by level, based on 3D digital models, is named Additive Manufacturing (AM) or 3D-printing. Amongs many AM methods, the Fused Deposition Modeling (FDM) technique along with PLA (Polylactic acid) material is commonly used in additive manufacturing. Until now, the mechanical properties of the AM components could not be calculated or estimated until they've been assembled and checked. In this work, a novel approach is suggested as to how the extrusion process affects the mechanical properties of the printed component to obtain how the parts can be manufactured or printed to achieve improved mechanical properties. This methodology is based on an experimental procedure in which the combination of parameters to achieve an optimal from a manufacturing experiment and its value can be determined, the results obtained show the effect of the extrusion process affects the mechanical properties.

scholarly journals Suitability of Recycled PLA Filament Application in Fused Filament Fabrication Process

2021 ◽  
Vol 15 (4) ◽  
pp. 491-497
Author(s):  
Tomislav Breški ◽  
Lukas Hentschel ◽  
Damir Godec ◽  
Ivica Đuretek
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Polylactic Acid ◽  
Design Of Experiment ◽  
Experimental Approach ◽  
Manufacturing Processes ◽  
Support Structures ◽  
Fused Filament Fabrication ◽  
Layer Height ◽  
Printing Parameters

Fused filament fabrication (FFF) is currently one of the most popular additive manufacturing processes due to its simplicity and low running and material costs. Support structures, which are necessary for overhanging surfaces during production, in most cases need to be manually removed and as such, they become waste material. In this paper, experimental approach is utilised in order to assess suitability of recycling support structures into recycled filament for FFF process. Mechanical properties of standardized specimens made from recycled polylactic acid (PLA) filament as well as influence of layer height and infill density on those properties were investigated. Optimal printing parameters for recycled PLA filaments are determined with Design of Experiment methods (DOE).

Temperature-compensated constitutive model of fused filament fabrication 3D printed PLA materials with full extrusion temperatures

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Kaiyang Zhu ◽  
Zichen Deng ◽  
Shi Dai ◽  
Yajun Yu
Keyword(s):  
Mechanical Properties ◽  
Thermal Decomposition ◽  
Constitutive Model ◽  
Polylactic Acid ◽  
Extrusion Temperature ◽  
Fused Filament Fabrication ◽  
Printing Process ◽  
Content Type ◽  
3D Printed ◽  
Interlayer Bonding

Purpose This study aims to focus on the effect of interlayer bonding and thermal decomposition on the mechanical properties of fused filament fabrication-printed polylactic acid specimens at high extrusion temperatures. Design/methodology/approach A printing process, that is simultaneous manufacturing of contour and specimen, is used to improve the printing accuracy at high extrusion temperatures. The effects of the extrusion temperature on the mechanical properties of the interlayer and intra-layer are evaluated via tensile experiments. In addition, the microstructure evolution affected by the extrusion temperature is observed using scanning electron microscopy. Findings The results show that the extrusion temperature can effectively improve the interlayer bonding property; however, the mechanical properties of the specimen for extrusion temperatures higher than 270°C may worsen owing to the thermal decomposition of the polylactic acid (PLA) material. The optimum extrusion temperature of PLA material in the three-dimensional (3D) printing process is recommended to be 250–270°C. Originality/value A temperature-compensated constitutive model for 3D printed PLA material under different extrusion temperatures is proposed. The present work facilitates the prediction of the mechanical properties of specimens at an extrusion temperature for different printing temperatures and different layers.

Sign in / Sign up

Export Citation Format

Share Document