scholarly journals Synthesis and Characterization of Syndiotactic Polystyrene-Polyethylene Block Copolymer

Polymers ◽  
2019 ◽  
Vol 11 (4) ◽  
pp. 698 ◽  
Author(s):  
Lamparelli ◽  
Speranza ◽  
Camurati ◽  
Buonerba ◽  
Oliva
Keyword(s):  
Direct Synthesis ◽  
Gel Permeation Chromatography ◽  
Syndiotactic Polystyrene ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Reaction Conditions ◽  
Force Microscopy ◽  
Synthetic Strategy ◽  
Atomic Force

The direct synthesis of syndiotactic polystyrene-block-polyethylene copolymer (sPS-b-PE) with a diblock structure has been achieved. The synthetic strategy consists of the sequential stereocontrolled polymerization of styrene and ethylene in the presence of a single catalytic system: cyclopentadienyltitanium(IV) trichloride activated by modified methylaluminoxane (CpTiCl3/MMAO). The reaction conditions suitable for affording the partially living polymerization of these monomers were identified, and the resulting copolymer, purified from contaminant homopolymers, was fully characterized. Gel permeation chromatography coupled with two-dimensional NMR spectroscopy COSY, HSQC, and DOSY confirmed the block nature of the obtained polymer, whose thermal behaviour and thin film morphology were also investigated by differential scanning calorimetry, powder wide angle x-ray diffraction, and atomic force microscopy.

Growth and Characterization of bulk GaN by Ga Vapor Transport

2004 ◽  
Vol 831 ◽  
Author(s):  
Phanikumar Konkapaka ◽  
Huaqiang Wu ◽  
Yuri Makarov ◽  
Michael G. Spencer
Keyword(s):  
Growth Rates ◽  
Vapor Transport ◽  
Spiral Growth ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Bulk Gan ◽  
Diffraction Patterns

ABSTRACTBulk GaN crystals of dimensions 8.5 mm × 8.5 mm were grown at growth rates greater than 200μm/hr using Gallium Vapor Transport technique. GaN powder and Ammonia were used as the precursors for growing bulk GaN. Nitrogen is used as the carrier gas to transport the Ga vapor that was obtained from the decomposition of GaN powder. During the process, the source GaN powder was kept at 1155°C and the seed at 1180°C. Using this process, it was possible to achieve growth rates of above 200 microns/hr. The GaN layers thus obtained were characterized using X-Ray diffraction [XRD], scanning electron microscopy [SEM], and atomic force microscopy [AFM]. X-ray diffraction patterns showed that the grown GaN layers are single crystals oriented along c direction. AFM studies indicated that the dominant growth mode was dislocation mediated spiral growth. Electrical and Optical characterization were also performed on these samples. Hall mobility measurements indicated a mobility of 550 cm2/V.s and a carrier concentration of 6.67 × 1018/cm3

Epitaxial Growth and Characterization of the Ordered Vacancy Compound CuIn3Se5 on GaAs (100) Fabricated by Molecular Beam Epitaxy

1994 ◽  
Vol 340 ◽  
Author(s):  
Art J. Nelson ◽  
M. Bode ◽  
G. Horner ◽  
K. Sinha ◽  
John Moreland
Keyword(s):  
Molecular Beam Epitaxy ◽  
Epitaxial Growth ◽  
Molecular Beam ◽  
Structural Defects ◽  
X Ray Diffraction ◽  
Symmetric Vibration ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron

ABSTRACTEpitaxial growth of the ordered vacancy compound (OVC) CuIn3Se5 has been achieved on GaAs (100) by molecular beam epitaxy (MBE) from Cu2Se and In2Se3 sources. Electron probe microanalysis and X-ray diffraction have confirmed the composition for the 1-3-5 OVC phase and that the film is single crystal Culn3Se5 (100). Transmission electron microscopy (TEM) characterization of the material also showed it to be single crystalline. Structural defects in the layer consisted mainly of stacking faults. Photoluminescence (PL) measurements performed at 7.5 K indicate that the bandgap is 1.28 eV. Raman spectra reveal a strong polarized peak at 152 cm−1, which is believed to arise from the totally symmetric vibration of the Se atoms in the lattice. Atomic force microscopy reveals faceting in a preferred (100) orientation.

Synthesis and Characterization of Linear Polymers for Non-Linear Optics through Click Chemistry Route

2012 ◽  
Vol 584 ◽  
pp. 8-12 ◽  
Author(s):  
Balakrishna Kolli ◽  
Sarada P. Mishra ◽  
Mukesh P. Joshi ◽  
S. Raj Mohan ◽  
T.S. Dhami ◽  
...  
Keyword(s):  
Click Chemistry ◽  
Second Harmonic ◽  
Gel Permeation Chromatography ◽  
Linear Polymers ◽  
Linear Optics ◽  
Scanning Calorimetry ◽  
Force Microscopy ◽  
Molecular Weights ◽  
Non Linear Optics ◽  
Atomic Force

Click chemistry is used for synthesizing polymers for second order NLO study. The molecular weights found by gel-permeation chromatography (GPC), were in the range of 7000-55000 g/mol. Differential scanning calorimetry shows glass transition temperature (Tg) above 120 oC. From electronic spectra order parameter of the poled films were calculated to be 0.1-0.5. The change in surface morphology after poling was checked by atomic force microscopy. By using a pulsed Nd:YAG laser (1064nm), the second harmonic generation (SHG) intensity was measured. The SHG intensity was also studied as a function of against temperature and time respectively.

Stability and Structural Characterization of Epitaxial NdNiO3 Films Grown by Pulsed Laser Deposition

2000 ◽  
Vol 658 ◽  
Author(s):  
Trong-Duc Doan ◽  
Cobey Abramowski ◽  
Paul A. Salvador
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Substrate Surface ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Atomic Force ◽  
Monoclinic Distortion

ABSTRACTThin films of NdNiO3 were grown using pulsed laser deposition on single crystal substrates of [100]-oriented LaAlO3 and SrTiO3. X-ray diffraction and reflectivity, scanning electron microscopy, and atomic force microscopy were used to characterize the chemical, morphological and structural traits of the thin films. Single-phase epitaxial films are grown on LaAlO3 and SrTiO3 at 625°C in an oxygen pressure of 200 mTorr. At higher temperatures, the films partially decompose to Nd2NiO4 and NiO. The films are epitaxial with the (101) planes (orthorhombic Pnma notation) parallel to the substrate surface. Four in-plane orientational variants exist that correspond to the four 90° degenerate orientations of the film's [010] with respect to the in-plane substrate directions. Films are observed to be strained in accordance with the structural mismatch to the underlying substrate, and this leads, in the thinnest films on LaAlO3, to an apparent monoclinic distortion to the unit cell.

scholarly journals New thermoplastic poly(carbonate-urethane) elastomers

2011 ◽  
Vol 13 (1) ◽  
pp. 23-30 ◽  
Author(s):  
Anna Kultys ◽  
Magdalena Rogulska
Keyword(s):  
Soft Segment ◽  
Tensile Tests ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Force Microscopy ◽  
Melt Polymerization ◽  
Atomic Force ◽  
Amorphous Structures ◽  
A Chain ◽  
Poly Carbonate

New thermoplastic poly(carbonate-urethane) elastomersTwo series of novel thermoplastic poly(carbonate-urethane) elastomers, with different hard-segment content (30 - 60 wt %), were synthesized by melt polymerization from poly(hexane-1,6-diyl carbonate) diol of Mn= 2000 as a soft segment, 4,4'-diphenylmethane diisocyanate (MDI) or hexane-1,6-diyl diisocyanate (HDI) and 6,6'-[methylenebis(1,4-phenylenemethylenethio)]dihexan-1-ol as a chain extender. The structure and basic properties of the polymers were examined by Fourier transform infrared spectroscopy, X-ray diffraction analysis, atomic force microscopy, differential scanning calorimetry, thermogravimetric analysis, Shore hardness and tensile tests. The resulting TPUs were colorless polymers, showing almost amorphous structures. The MDI-based TPUs showed higher tensile strengths (up to 21.3 MPa vs. 15.8 MPa) and elongations at break (up to 550% vs. 425%), but poorer low-temperature properties than the HDI-based analogs.

STUDIES ON SURFACE STRUCTURE, MORPHOLOGY AND COMPOSITION OF Co–W COATINGS ELECTRODEPOSITED WITH DIRECT AND PULSE CURRENT USING GLUCONATE BATH

2013 ◽  
Vol 20 (01) ◽  
pp. 1350006 ◽  
Author(s):  
PARTHASARATHI BERA ◽  
H. SEENIVASAN ◽  
K. S. RAJAM
Keyword(s):  
Photoelectron Spectroscopy ◽  
Pulse Current ◽  
Diffraction Field ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Force Microscopy ◽  
Dsc Studies ◽  
Atomic Force ◽  
Electrodeposited Coating

Co–W alloy coatings were deposited with direct current (DC) and pulse current (PC) electrodeposition methods using gluconate bath at pH5 and characterized by X-ray diffraction, field emission scanning electron microscopy, atomic force microscopy, differential scanning calorimetry (DSC) and X-ray photoelectron spectroscopy (XPS). DSC studies hint at the possibility of formation of metallic glasses. Detailed XPS studies of these alloy coatings have been carried out to compare elemental states and composition of Co and W in DC and PC electrodeposited alloys. DC-plated alloy has significant amount of Co and W metal along with their respective oxidized species. In contrast, mainly oxidized metals are present in the following layers of as-deposited coatings prepared with PC plating. Concentration of Co metal is observed to increase during sputtering, whereas there is no change in W6+ concentration. Microhardness measurement of all the Co–W coatings shows higher hardness compared to Co metal and 1:1 and 1:4 PC electrodeposited coatings show little higher hardness compared to 1:2 PC electrodeposited coating.

Effects of Annealing on Pulsed Laser Deposited TiO2 Thin Films

2013 ◽  
Vol 446-447 ◽  
pp. 306-311 ◽  
Author(s):  
Sudhanshu Dwivedi ◽  
Somnath Biswas
Keyword(s):  
Thin Films ◽  
Pulsed Laser ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Si Substrates ◽  
Morphological Studies ◽  
Atomic Force ◽  
Deposited Films ◽  
Type Crystal

Mixed phase TiO2 thin films of rutile and anatase type crystal orientations were deposited on Si substrates by pulsed laser deposition (PLD) technique. When annealed at 800°C at 1 mbar oxygen pressure for 3 h, the deposited films transform into a single phase of rutile type. Structural and morphological studies of the as-deposited and annealed films were performed with X-ray diffraction (XRD), Fourier transform infra-red spectroscopy (FTIR), Raman spectroscopy, and atomic force microscopy (AFM). Photoluminescence (PL) spectroscopy was used for optical characterization of the annealed thin films.

Characterization of kaolinite in the hardsetting clay fraction using atomic force microscopy, X-ray diffraction, and the Rietveld method

2017 ◽  
Vol 17 (8) ◽  
pp. 2144-2155 ◽  
Author(s):  
Luis Valério Prandel ◽  
Nívea Maria Piccolomini Dias ◽  
Sérgio da Costa Saab ◽  
André Maurício Brinatti ◽  
Neyde Fabíola Balarezo Giarola ◽  
...  
Keyword(s):  
Atomic Force Microscopy ◽  
Rietveld Method ◽  
Clay Fraction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force

Differential height characteristics of plasmid and G-wire DNA as determined by AFM

1994 ◽  
Vol 52 ◽  
pp. 1052-1053
Author(s):  
T. C. Marsh ◽  
J. Vesenka ◽  
E. Henderson
Keyword(s):  
Plasmid Dna ◽  
Structural Characteristics ◽  
Three Dimensional ◽  
Helical Structure ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Dimension One

Atomic-Force Microscopy (AFM) has become an effective tool in the three dimensional characterization of biological systems and is capable of Angstrom sensitivity in the vertical dimension. One unresolved dilemma is that the observed height (diameter) of B-DNA being about 10Å, is less than half its x-ray diffraction value. In this paper we attempt to determine the source of this discrepancy by comparing plasmid DNA co-deposited with a novel form of DNA called “G-wires” (Figure 1). G-wires are formed by G-rich sequences. They are composed of G-4 DNA, a quadruple helical structure. X-ray data of G-4 DNA gives a diameter of 27Å, comparable to that expected for B-DNA (20 to 25Å). In the AFM these structures have a significantly greater height (av. = 22 Å) compared to double stranded (av. = 7 Å) or supercoiled B-DNA (av. = 14 Å) (Figure 2). Thus, the apparent height of nucleic acids in the AFM is dependent upon their innate structural characteristics.

scholarly journals Characterization of the Spindle Morphology Nanomicelles Assembled from Sericin and Gelatin

2017 ◽  
Vol 2017 ◽  
pp. 1-9
Author(s):  
Xiaozhou Su ◽  
Lei Li ◽  
Weihan Huang
Keyword(s):  
Electron Microscopy ◽  
Protein Concentration ◽  
Scanning Calorimetry ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Ft Ir ◽  
And Storage ◽  
Ft Ir Spectroscopy

Complex nanomicelles were prepared by sericin and type A gelatin with molecular weight of 5789 Da and 128664 Da separately. The assembling conditions were as follows: mass ratio (sericin/gelatin) was 1 : 1, protein concentration was 0.5%, temperature was 35°C, and assembling time was 18 hours. Scanning electron microscopy (SEM), atomic force microscopy (AFM), transmission electron microscopy (TEM), Fourier transform infrared (FT-IR) spectroscopy, differential scanning calorimetry (DSC), and dynamic light scattering (DLS) were conducted to observe and characterize the complex nanomicelles. Results showed that the complex sericin/gelatin micelles was a kind of nanospindle micelles. The micelles had high electrochemical stability, thermal stability, antidilution stability, and storage stability.

Sign in / Sign up

Export Citation Format

Share Document