scholarly journals Mechanically and Thermally Induced Degradation and Modification of Cereal Biopolymers during Grinding

Polymers ◽  
2019 ◽  
Vol 11 (3) ◽  
pp. 448 ◽  
Author(s):  
Sabina Paulik ◽  
Mario Jekle ◽  
Thomas Becker
Keyword(s):  
Mechanical Stress ◽  
Structural Modification ◽  
Wheat Starch ◽  
Water Addition ◽  
Scanning Calorimetry ◽  
Hydration Properties ◽  
Thermally Induced ◽  
Induced Changes ◽  
The Impact ◽  
Main Factor

It is presumed that structural and functional alterations of biopolymers, which occur during grinding, are caused by a mechanical modification of polymers. As a result, thermally induced changes of flours are neglected. In this study, the impact of thermo-mechanical stress (TMS), as occurring during general grinding procedures, was further differentiated into thermal stress (TS) and mechanical stress (MS). For TS, native wheat flour, as well as the purified polymers of wheat—starch and gluten—were heated without water addition up to 110 ∘ C. Isolated MS was applied in a temperature-controlled ultra-centrifugal grinder (UCG), whereby thermal and mechanical treatment (TMS) was simultaneously performed in a non-cooled UCG. TS starch (110 ∘ C) and reference starch did not show differences in starch modification degree (2.53 ± 0.24 g/100 g and 2.73 ± 0.15 g/100 g, AACC 76-31), gelatinization onset (52.44 ± 0.14 ∘ C and 52.73 ± 0.27 ∘ C, differential scanning calorimetry (DSC)) and hydration properties (68.9 ± 0.8% dm and 75.8 ± 3.0%, AACC 56-11), respectively. However, TS led to an elevated gelatinization onset and a rise of water absorption of flours (Z-kneader) affecting the processing of cereal-based dough. No differences were visible between MS and TMS up to 18,000 rpm regarding hydration properties (65.0 ± 2.0% dm and 66.5 ± 0.3% dm, respectively). Consequently, mechanical forces are the main factor controlling the structural modification and functional properties of flours during grinding.

Thermally induced changes in reconstituted and membranous cytochrome c oxidase

1979 ◽  
Vol 57 (3) ◽  
pp. 238-249 ◽  
Author(s):  
A. S. Denes ◽  
N. Z. Stanacev
Keyword(s):  
Cytochrome C ◽  
Cytochrome C Oxidase ◽  
Spin Label ◽  
Liquid Crystalline ◽  
Spectral Characteristics ◽  
Temperature Dependent ◽  
Scanning Calorimetry ◽  
Thermally Induced ◽  
Lipid Protein Interaction ◽  
Induced Changes

The Arrhenius plots of electron transport activity in cytochrome c oxidase reconstituted with well-defined phospholipids have been shown to display a change in slope at 20–25 °C regardless of the chemical nature of the incorporated lipid. In native membranous cytochrome c oxidase, the discontinuity in Arrhenius activity plot occurred at 16–18 °C. These temperature breaks were found to correlate with changes in spin-label mobilities but not with the bulk lipid transition observed by differential scanning calorimetry. Temperature-dependent reciprocal equilibrium between the immobilized and fluid pools is demonstrated. It is suggested that the changes in kinetic and spin-label spectral characteristics in cytochrome c oxidase membranes are related very likely to a lipid-protein interaction prompted by a thermally induced change in the physical state of the lipids that does not involve a gel to liquid crystalline transition.

scholarly journals Thermally Induced Mechanical Stress in the Stator Windings of Electrical Machines

Energies ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 2113 ◽  
Author(s):  
Bishal Silwal ◽  
Peter Sergeant
Keyword(s):  
Mechanical Stress ◽  
Temperature Cycling ◽  
Electrical Machines ◽  
Electrical Machine ◽  
Thermally Induced ◽  
Stator Windings ◽  
Mechanical Models ◽  
Set Up ◽  
Winding Insulation ◽  
Main Factor

The lifetime of an electrical machine mainly depends on the thermal overloading. Modern day applications of electrical machines on one hand require compact machines with high power density, while on the other hand force electrical machines to undergo frequent temperature cycling. Until recently, in the case of electrical machines, the main factor related to the degradation of the winding insulation was thought to be the thermal oxidization of the insulation materials. It has now been revealed that thermal overloading can also induce mechanical stress in the windings of electrical machines, which over time could lead to fatigue and degradation. In this paper, a comprehensive study of the thermally induced mechanical stress in the windings of an electrical machine is presented. The study is performed using combined thermo-mechanical models. The numerical results are validated by experiments on a segmented stator winding set-up.

Drug Induced Changes in Cell Organelles

1968 ◽  
Vol 26 ◽  
pp. 110-111
Author(s):  
Sarah A. Luse
Keyword(s):  
Clinical Medicine ◽  
Cell Organelles ◽  
Riboflavin Deficiency ◽  
Drug Induced ◽  
New Era ◽  
Health And Disease ◽  
In The Beginning ◽  
Cellular Pathology ◽  
Induced Changes ◽  
The Impact

In the mid-nineteenth century Virchow revolutionized pathology by introduction of the concept of “cellular pathology”. Today, a century later, this term has increasing significance in health and disease. We now are in the beginning of a new era in pathology, one which might well be termed “organelle pathology” or “subcellular pathology”. The impact of lysosomal diseases on clinical medicine exemplifies this role of pathology of organelles in elucidation of disease today.Another aspect of cell organelles of prime importance is their pathologic alteration by drugs, toxins, hormones and malnutrition. The sensitivity of cell organelles to minute alterations in their environment offers an accurate evaluation of the site of action of drugs in the study of both function and toxicity. Examples of mitochondrial lesions include the effect of DDD on the adrenal cortex, riboflavin deficiency on liver cells, elevated blood ammonia on the neuron and some 8-aminoquinolines on myocardium.

Effect of Glycosaminoglycans on Thrombin- and Atroxin-Induced Fibrin Assembly and Structure

1989 ◽  
Vol 62 (04) ◽  
pp. 1057-1061 ◽  
Author(s):  
Marcus E Carr ◽  
Patrick L Powers
Keyword(s):  
Chondroitin Sulfate ◽  
Fiber Diameter ◽  
Lag Phase ◽  
Low Molecular Weight ◽  
Fibrin Gels ◽  
Fiber Size ◽  
Induced Changes ◽  
The Impact ◽  
Fiber Radius ◽  
Turbidity Increase

SummaryThis study was performed to quantitate the impact of several glycosaminoglycans (GAG) on fibrin assembly and structure. Gel formation was monitored as the increase in optical density at 633 nm subsequent to thrombin (2 NIH u/ml) or atroxin (0.10 mg/ml) addition to solutions of buffered fibrinogen (1 mg/ml) or plasma. Gel absorbance was measured as a function of wavelength (400 to 800 nm) and gel fiber diameter and mass/length ratio (μ) were calculated. Chondroitin sulfate A (CSA)shortened the lag phase, enhanced the maximal rate of turbidity increase, and increased the final gel turbidity of fibrin gels formed by thrombin or atroxin. CSA (16 mg/ml) increased fiber μ from 1.3 to 3.1 × 1013 dalton/cm and fiber radius from 6.0 to 8.6 × 10-6 cm in thrombin-induced gels. μ increased from 0.7 to 2.7 × 1013 dalton/cm and fiber radius from 4 to 7.8 × 10-6 cm for atroxin-induced gels. Above 16 mg/ml, CSA caused fibrinogen precipitation in purified solutions but not in plasma. CSA inhibited thrombin-induced plasma clotting of plasma but effects in atroxin-mediated plasma gels paralleled those seen in purified solutions. Chondroitin sulfate B (CSB)-induced changes in fibrin were similar but slightly less dramatic than those seen with CSA. μ increased from 0.9 to 2.0 × 1013 dalton/cm for thrombin-induced fibrin gels and from 0.8 to 2.3 × 1013 dalton/cm for atroxininduced gels. Low molecular weight heparin (Mr = 5100) slowed fibrin assembly and reduced fiber size by 50% in thrombininduced gels. Changes in μ of atroxin-induced gels were much less pronounced (<20%). This study documents pronounced GAGinduced changes in fibrin structure which vary with GAG species and may mediate significant physiologic functions.

scholarly journals Numerical simulation of the impact of an integrated renovation project on the Maowei Sea hydrodynamic environment

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Cui Wang ◽  
Ling Cai ◽  
Yaojian Wu ◽  
Yurong Ouyang
Keyword(s):  
Water Exchange ◽  
Land Reclamation ◽  
Three Dimensional ◽  
Exchange Capacity ◽  
Reclamation Project ◽  
Hydrodynamic Environment ◽  
Sea Area ◽  
Water Quality Models ◽  
The Impact ◽  
Main Factor

AbstractIntegrated renovation projects are important for marine ecological environment protection. Three-dimensional hydrodynamics and water quality models are developed for the Maowei Sea to assess the hydrodynamic environment base on the MIKE3 software with high resolution meshes. The results showed that the flow velocity changed minimally after the project, decreasing by approximately 0.12 m/s in the east of the Maowei Sea area and increasing by approximately 0.01 m/s in the northeast of the Shajing Port. The decrease in tidal prism (~ 2.66 × 106 m3) was attributed to land reclamation, and accounted for just 0.86% of the pre-project level. The water exchange half-life increased by approximately 1 day, implying a slightly reduced water exchange capacity. Siltation occurred mainly in the reclamation and dredging areas, amounting to back-silting of approximately 2 cm/year. Reclamation project is the main factor causing the decrease of tidal volume and weakening the hydrodynamics in Maowei Sea. Adaptive management is necessary for such a comprehensive regulation project. According to the result, we suggest that reclamation works should strictly prohibit and dredging schemes should optimize in the subsequent regulation works.

scholarly journals Exogenous application of growth stimulators improves the condition of maize exposed to soil drought

2021 ◽  
Vol 43 (4) ◽  
Author(s):  
Agnieszka Ostrowska ◽  
Maciej T. Grzesiak ◽  
Tomasz Hura
Keyword(s):  
Plant Growth ◽  
Developmental Stages ◽  
Aminolevulinic Acid ◽  
Stem Elongation ◽  
Development Stage ◽  
Photochemical Activity ◽  
Soil Drought ◽  
Beneficial Effects ◽  
Induced Changes ◽  
The Impact

AbstractSoil drought is a major problem in plant cultivation. This is particularly true for thermophilic plants, such as maize, which grow in areas often affected by precipitation shortage. The problem may be alleviated using plant growth and development stimulators. Therefore, the aim of the study was to analyze the effects of 5-aminolevulinic acid (5-ALA), zearalenone (ZEN), triacontanol (TRIA) and silicon (Si) on water management and photosynthetic activity of maize under soil drought. The experiments covered three developmental stages: three leaves, stem elongation and heading. The impact of these substances applied during drought stress depended on the plant development stage. 5-ALA affected chlorophyll levels, gas exchange and photochemical activity of PSII. Similar effects were observed for ZEN, which additionally induced stem elongation and limited dehydration. Beneficial effects of TRIA were visible at the stage of three leaves and involved leaf hydration and plant growth. A silicon preparation applied at the same developmental stage triggered similar effects and additionally induced changes in chlorophyll levels. All the stimulators significantly affected transpiration intensity at the heading stage.

scholarly journals Spatio-Temporal Variation Characteristics of Snow Depth and Snow Cover Days over the Tibetan Plateau

Water ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 307
Author(s):  
Chi Zhang ◽  
Naixia Mou ◽  
Jiqiang Niu ◽  
Lingxian Zhang ◽  
Feng Liu
Keyword(s):  
Tibetan Plateau ◽  
Snow Cover ◽  
Snow Depth ◽  
Feedback Effect ◽  
Effect Of Temperature ◽  
The Tibetan Plateau ◽  
Reanalysis Dataset ◽  
Spatio Temporal ◽  
The Impact ◽  
Main Factor

Changes in snow cover over the Tibetan Plateau (TP) have a significant impact on agriculture, hydrology, and ecological environment of surrounding areas. This study investigates the spatio-temporal pattern of snow depth (SD) and snow cover days (SCD), as well as the impact of temperature and precipitation on snow cover over TP from 1979 to 2018 by using the ERA5 reanalysis dataset, and uses the Mann–Kendall test for significance. The results indicate that (1) the average annual SD and SCD in the southern and western edge areas of TP are relatively high, reaching 10 cm and 120 d or more, respectively. (2) In the past 40 years, SD (s = 0.04 cm decade−1, p = 0.81) and SCD (s = −2.3 d decade−1, p = 0.10) over TP did not change significantly. (3) The positive feedback effect of precipitation is the main factor affecting SD, while the negative feedback effect of temperature is the main factor affecting SCD. This study improves the understanding of snow cover change and is conducive to the further study of climate change on TP.

scholarly journals Polypropylene/Lignin/POSS Nanocomposites: Thermal and Wettability Properties, Application in Water Remediation

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3950
Author(s):  
Abeer Alassod ◽  
Syed Rashedul Islam ◽  
Mina Shahriari Khalaji ◽  
Rogers Tusiime ◽  
Wanzhen Huang ◽  
...  
Keyword(s):  
Organic Liquid ◽  
Contact Angles ◽  
Water Remediation ◽  
Scanning Calorimetry ◽  
Water Contact ◽  
Thermally Induced ◽  
Dsc Measurements ◽  
Infrared Measurement ◽  
Oligomeric Silsesquioxane ◽  
Tga And Dsc

Compositing is an interesting strategy that has always been employed to introduce or enhance desired functionalities in material systems. In this paper, sponges containing polypropylene, lignin, and octavinyl-polyhedral oligomeric silsesquioxane (OV-POSS) were successfully prepared via an easy and elegant strategy called thermally induced phase separation (TIPS). To fully explore the behaviour of different components of prepared sponges, properties were characterized by a thermogravimetric analyser (TGA), differential scanning calorimetry (DSC), Fourier transform infrared measurement (FTIR), and scanning electron microscopy (SEM). Furthermore, wettability properties toward an organic liquid and oil were investigated. The FTIR analysis confirmed the chemical modification of the components. TGA and DSC measurements revealed thermal stability was much better with an increase in OV-POSS content. OV-POSS modified sponges exhibited ultra-hydrophobicity and high oleophilicity with water contact angles of more than 125°. The SEM revealed that POSS molecules acted as a support for reduced surface roughness. Moreover, OV-POSS-based blend sponges showed higher sorption capacities compared with other blend sponges without OV-POSS. The new blend sponges demonstrated a potential for use as sorbent engineering materials in water remediation.

scholarly journals The Correlation between Physical Crosslinking and Water-Soluble Drug Release from Chitosan-Based Microparticles

Pharmaceutics ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 455
Author(s):  
Emilia Szymańska ◽  
Katarzyna Woś-Latosi ◽  
Julia Jacyna ◽  
Magdalena Dąbrowska ◽  
Joanna Potaś ◽  
...  
Keyword(s):  
Drug Release ◽  
Polymer Matrix ◽  
Drug Loading ◽  
Water Soluble ◽  
Dissolution Behavior ◽  
Complex Nature ◽  
Prolonged Release ◽  
Scanning Calorimetry ◽  
Burst Effect ◽  
The Impact

Microparticles containing water-soluble zidovudine were prepared by spray-drying using chitosan glutamate and beta-glycerophosphate as an ion crosslinker (CF). The Box–Behnken design was applied to optimize the microparticles in terms of their drug loading and release behavior. Physicochemical studies were undertaken to support the results from dissolution tests and to evaluate the impact of the crosslinking ratio on the microparticles’ characteristics. The zidovudine dissolution behavior had a complex nature which comprised two phases: an initial burst effect followed with a prolonged release stage. The initial drug release, which can be modulated by the crosslinking degree, was primarily governed by the dissolution of the drug crystals located on the microparticles’ surfaces. In turn, the further dissolution stage was related to the drug diffusion from the swollen polymer matrix and was found to correlate with the drug loading. Differential Scanning Calorimetry (DSC) studies revealed the partial incorporation of a non-crystallized drug within the polymer matrix, which correlated with the amount of CF. Although CF influenced the swelling capacity of chitosan glutamate microparticles, surprisingly a higher amount of CF did not impact the time required for 80% of the drug to be released markedly. The formulation with the lowest polymer:CF ratio, 3:1, was selected as optimal, providing satisfactory drug loading and displaying a moderate burst effect within the first 30 min of the study, followed with a prolonged drug release of up to 210 min.

Sign in / Sign up

Export Citation Format

Share Document