scholarly journals Hydrophobicity of Polyacrylate Emulsion Film Enhanced by Introduction of Nano-SiO2 and Fluorine

Polymers ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 255
Author(s):  
Tao Xu ◽  
Qiangqiang Xiao ◽  
Jiayu Chen ◽  
Li Li ◽  
Xiongjun Yang ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Photoelectron Spectroscopy ◽  
Silicon Nanoparticles ◽  
Shielding Effect ◽  
Nano Sio2 ◽  
Fluorinated Polyacrylate ◽  
Air Interface ◽  
Emulsion Film ◽  
Emulsion Films ◽  
Ultraviolet Shielding

This study proposes to utilize modified Nano-SiO2/fluorinated polyacrylate emulsion that was synthesized with a semi-continuous starved seed emulsion polymerization to improve the hydrophobicity, thermal stability, and UV-Vis absorption of polyacrylate emulsion film. To verify the proposed method, a series inspection had been conducted to investigate the features of the emulsion film. The morphological analysis indicated that Nano-SiO2 was surrounded by a silane molecule after modification, which can efficiently prevent silica nanoparticles from aggregating. Fourier transform infrared spectra confirmed that modified SiO2 and dodecafluoroheptyl methacrylate (DFMA) were successfully introduced to the copolymer latex. The particle size of latex increased with the introduction of modified Nano-SiO2 and DFMA. UV-Vis absorption spectra revealed that modified silicon nanoparticles can improve the ultraviolet shielding effect obviously. X-ray photoelectron spectroscopy illustrated that the film–air interface was richer in fluorine than film section and the glass side. The contact angle of modified Nano-SiO2/fluorinated polyacrylate emulsion containing 3 wt % DFMA was 112°, slightly lower than double that of polyacrylate emulsion, indicating composite emulsion films possess better hydrophobicity. These results suggest that introducing modified Nano-SiO2 and fluorine into polyacrylate emulsion can significantly enhance the thermal stability of emulsion films.

scholarly journals Design of Sodium Alginate/Gelatin-Based Emulsion Film Fused with Polylactide Microparticles Charged with Plant Extract

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 745 ◽  
Author(s):  
Weronika Prus-Walendziak ◽  
Justyna Kozlowska
Keyword(s):  
Sodium Alginate ◽  
Plant Extract ◽  
Contact Angles ◽  
Polymeric Films ◽  
Solvent Evaporation Method ◽  
Calendula Officinalis ◽  
Flower Extract ◽  
Polymeric Microparticles ◽  
Emulsion Film ◽  
Emulsion Films

This study aimed at designing emulsion films based on sodium alginate, gelatin, and glycerol, and their modification by the addition of lipids (cottonseed oil and beeswax). Film composition with the most promising properties was further modified by the incorporation of polylactide (PLA) microparticles with Calendula officinalis flower extract. PLA microspheres were obtained by the emulsion/solvent evaporation method. The size distribution of oily particles in emulsions was investigated. Mechanical properties, moisture content, UV-Vis spectra, and the color of films were analyzed, while biophysical skin parameters were assessed after their application to the skin. Moreover, the contact angles were measured, and the surface free energy of polymeric films was determined. An investigation of the amount of Calendula officinalis flower extract which can be incorporated into PLA microparticles was performed. The modification of the composition of films significantly influenced their physicochemical properties. The selected active ingredient in the form of plant extract was successfully incorporated into polymeric microparticles that were further added into the developed emulsion film. The condition of the skin after the application of obtained emulsion films improved. The prepared materials, especially containing microparticles with plant extract, can be considered for designing new cosmetic forms, such as cosmetic masks, as well as new topical formulations for pharmaceutical delivery.

scholarly journals Improvement of the thermal stability of dendritic silver-coated copper microparticles by surface modification based on molecular self-assembly

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
Tae Hyeong Kim ◽  
Hyeji Kim ◽  
Hyo Jun Jang ◽  
Nara Lee ◽  
Kwang Hyun Nam ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Photoelectron Spectroscopy ◽  
Self Assembly ◽  
Electrically Conductive ◽  
X Ray ◽  
Alkyl Chains ◽  
Conductive Film ◽  
Initial Resistance ◽  
Thermal Stability Of ◽  
Scanning Electron

AbstractIn the study reported herein, silver-coated copper (Ag/Cu) powder was modified with alkanethiols featuring alkyl chains of different lengths, namely butyl, octyl, and dodecyl, to improve its thermal stability. The modification of the Ag/Cu powders with adsorbed alkanethiols was confirmed by scanning electron microscopy with energy dispersive spectroscopy, X-ray photoelectron spectroscopy, and thermogravimetric analysis. Each powder was combined with an epoxy resin to prepare an electrically conductive film. The results confirmed that the thermal stability of the films containing alkanethiol-modified Ag/Cu powders is superior to that of the film containing untreated Ag/Cu powder. The longer the alkyl group in the alkanethiol-modified Ag/Cu powder, the higher the initial resistance of the corresponding electrically conductive film and the lower the increase in resistance induced by heat treatment.

scholarly journals Phosphated Avocado Seed: A Renewable Biomaterial for Preparing a Flame Retardant Biofiller

2021 ◽  
Author(s):  
DAVID Zuluaga-Parra ◽  
L.F Ramos-deValle ◽  
Saul Sanchez ◽  
J.R. Torres-Lubián ◽  
J.A. Rodríguez-Gonzalez ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Chemical Modification ◽  
Flame Retardant ◽  
Photoelectron Spectroscopy ◽  
Morphological Changes ◽  
Ethylene Vinyl Acetate ◽  
Chemically Modified ◽  
Air Atmosphere ◽  
Thermal Stability Of ◽  
Avocado Seed

Abstract The cellulose and starch present in the avocado seed can be chemically modified to obtain biofillers with fire retarding characteristics. The resulting composites could be used as substitute of the corresponding halogenated composites. For this, the avocado seed was first washed, dehydrated and pulverized, and thereafter, chemically modified with phosphoric acid in the presence of urea. This was studied using infrared spectroscopy, nuclear magnetic resonance and X-Ray photoelectron spectroscopy, in order to determine the resulting chemical structure and confirm the presence of the proposed functional groups. In addition, scanning electron microscopy and elemental analysis were used, respectively, to establish the resulting morphological changes, as well as the elements present on the surface of the modified material. Thermogravimetric analysis was also carried out in order to establish the thermal stability of the material and predict the effect on the flame retardancy due to the mentioned chemical modification. Further tests established that the obtained modified structure and morphology of the avocado seed was highly dependent on the method used to dehydrate the pulverized avocado seed. It was also determined that chemical modification greatly increased the thermal stability of the avocado seed in air atmosphere. The flame-retardant effect of the modified avocado seed was assessed in polyethylene/ethylene-vinyl-acetate (PE/EVA) composites via cone calorimeter tests. These results showed that the modified avocado seed decreased the peak of the heat release rate (pHRR) by 50% and the total heat released (THR) by 15%. This phosphated avocado seed could be a good option as a renewable biofiller for polymer composites with enhanced flame-retardant properties.

scholarly journals Thermal Stability of Octadecyltrichlorosilane and Perfluorooctyltriethoxysilane Monolayers on SiO2

Nanomaterials ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 210
Author(s):  
Xiangdong Yang ◽  
Haitao Wang ◽  
Peng Wang ◽  
Xuxin Yang ◽  
Hongying Mao
Keyword(s):  
Thermal Stability ◽  
Thermal Behavior ◽  
Work Function ◽  
Photoelectron Spectroscopy ◽  
Vacuum Annealing ◽  
Moderate Temperature ◽  
Ultraviolet Photoelectron Spectroscopy ◽  
X Ray ◽  
Thermal Stability Of

Using in situ ultraviolet photoelectron spectroscopy (UPS) and X-ray photoelectron spectroscopy (XPS) measurements, the thermal behavior of octadecyltrichlorosilane (OTS) and 1H, 1H, 2H, and 2H-perfluorooctyltriethoxysilane (PTES) monolayers on SiO2 substrates has been investigated. OTS is thermally stable up to 573 K with vacuum annealing, whereas PTES starts decomposing at a moderate temperature between 373 K and 423 K. Vacuum annealing results in the decomposition of CF3 and CF2 species rather than desorption of the entire PTES molecule. In addition, our UPS results reveal that the work function (WF)of OTS remains the same after annealing; however WF of PTES decreases from ~5.62 eV to ~5.16 eV after annealing at 573 K.

scholarly journals Capping Agent Effect on Pd-Supported Nanoparticles in the Hydrogenation of Furfural

Catalysts ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 11 ◽  
Author(s):  
Shahram Alijani ◽  
Sofia Capelli ◽  
Stefano Cattaneo ◽  
Marco Schiavoni ◽  
Claudio Evangelisti ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Active Sites ◽  
Catalytic Performance ◽  
Shielding Effect ◽  
Capping Agents ◽  
X Ray ◽  
Supported Nanoparticles ◽  
Liquid Phase Hydrogenation ◽  
Diallyldimethylammonium Chloride ◽  
Transmission Electron

The catalytic performance of a series of 1 wt % Pd/C catalysts prepared by the sol-immobilization method has been studied in the liquid-phase hydrogenation of furfural. The temperature range studied was 25–75 °C, keeping the H2 pressure constant at 5 bar. The effect of the catalyst preparation using different capping agents containing oxygen or nitrogen groups was assessed. Polyvinyl alcohol (PVA), polyvinylpyrrolidone (PVP), and poly (diallyldimethylammonium chloride) (PDDA) were chosen. The catalysts were characterized by ultraviolet-visible spectroscopy (UV-Vis), Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The characterization data suggest that the different capping agents affected the initial activity of the catalysts by adjusting the available Pd surface sites, without producing a significant change in the Pd particle size. The different activity of the three catalysts followed the trend: PdPVA/C > PdPDDA/C > PdPVP/C. In terms of selectivity to furfuryl alcohol, the opposite trend has been observed: PdPVP/C > PdPDDA/C > PdPVA/C. The different reactivity has been ascribed to the different shielding effect of the three ligands used; they influence the adsorption of the reactant on Pd active sites.

Study on Preparation and Surface Properties of Fluorinated Acrylate Hydrophobic Polymer Film

2015 ◽  
Vol 1088 ◽  
pp. 101-106
Author(s):  
Jing Chen ◽  
Qian Cheng ◽  
Shun Quan Chen
Keyword(s):  
Contact Angle ◽  
Water Content ◽  
Polymer Film ◽  
Water Contact ◽  
Fluorinated Acrylate ◽  
Fluorinated Polyacrylate ◽  
Hydrophobic Polymer ◽  
Air Interface ◽  
Surface Morphologies ◽  
Lower Water Content

A new fluorinated acrylate terpolymer hydrophobic polymer was prepared by emulsifier-free inverse microemulsion polymerization using methyl methacrylate (MMA) and hexafluorobutyl acrylate (HFBA) as monomers, and methyl polyethylene glycol methacrylate (MPEGMA) as polymerizable emulsifier. Membrane properties were characterized by means of FT-IR, SEM and Contact Angle Meter. The effect of fluorinated monomer content, water content in the inverse precursor microemulsion on the surface morphologies and hydrophobicity of the polymer film was mainly discussed. Morphological studies of the fluorinated polyacrylate polymers by SEM showed that discrete granular microstructures were obtained from precursor microemulsion with higher water content. On the other hand, smooth and continuous surface morphologies were found with lower water content. Contact angle revealed that the fluorine preferentially enriched at the film-air interface and more hydrophobic that the film-glass interface. The amount of HFBA had significantly effects on the film properties. The water contact angle of the film-air interface increased as the amount of HFBA increased from 0 ml to 4 ml and then remained almost unchangeable. The film formed from the fluorinated polyacrylate polymer with higher water content in the precursor microemulsion exhibited better hydrophobicity in comparison with the film formed from the fluorinated polyacrylate polymer with the lower water content, and it confirmed that rough surface have high water contact angles.

Sign in / Sign up

Export Citation Format

Share Document