scholarly journals Kinetic, Isotherm, and Thermodynamic Studies for Ag(I) Adsorption Using Carboxymethyl Functionalized Poly(glycidyl methacrylate)

Polymers ◽  
2018 ◽  
Vol 10 (10) ◽  
pp. 1090 ◽  
Author(s):  
Jiling Zhao ◽  
Shixing Wang ◽  
Libo Zhang ◽  
Chen Wang ◽  
Bing Zhang
Keyword(s):  
Photoelectron Spectroscopy ◽  
Glycidyl Methacrylate ◽  
Adsorption Process ◽  
Removal Rate ◽  
Single Layer ◽  
Silver Ions ◽  
Ion Concentration ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
Kinetics And Isotherms

Industrial wastewater contains large amounts of silver ions. Here, a new adsorbent was synthesized by functionalizing poly(glycidyl methacrylate) with carboxymethyl groups. The adsorbent was used to recover Ag(I) in wastewater. Fourier transform infrared spectroscopy, zeta potential, scanning electron microscopy, and X-ray photoelectron spectroscopy were used to characterize the adsorbent. The experimental parameters affecting the adsorption are solution pH, contact time, and initial silver ion concentration. The optimum pH for adsorption of Ag(I) is pH 4. The maximum adsorption capacity at pH 4 is 157.05 mg/g, and the adsorption reaches equilibrium at 300 min. The kinetics and isotherms of the adsorption process were described by pseudo second-order, Langmuir and D-R models, respectively. The adsorption process was a single layer chemical adsorption, exothermic, feasible, and spontaneous. The adsorption mechanism is electrostatic or chelation. The adsorbent selectively absorbed Ag(I) from coexisting ions (Cu2+, Ni2+, Co2+, Zn2+). Finally, the removal rate of silver ions decreased from 79.29% to 65.01% after four repetitive experiments, which proved that the adsorbent had good reusability. The adsorbent has great potential benefit in removing Ag(I).

scholarly journals Removal of Tetracycline by Hydrous Ferric Oxide: Adsorption Kinetics, Isotherms, and Mechanism

2019 ◽  
Vol 16 (22) ◽  
pp. 4580 ◽  
Author(s):  
Ji Zang ◽  
Tiantian Wu ◽  
Huihui Song ◽  
Nan Zhou ◽  
Shisuo Fan ◽  
...  
Keyword(s):  
Adsorption Kinetics ◽  
Ferric Oxide ◽  
Photoelectron Spectroscopy ◽  
Electrostatic Interactions ◽  
Adsorption Process ◽  
Inhibitory Effect ◽  
Maximum Adsorption Capacity ◽  
Hydrous Ferric Oxide ◽  
X Ray ◽  
Kinetics And Isotherms

The removal of tetracycline (TC) from solution is an important environmental issue. Here we prepared an adsorbent hydrous ferric oxide (HFO) by adjusting a FeCl3·6H2O solution to neutral pH. HFO was characterized by a surface area analyzer, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS), and was used to remove TC from solution. The influence of pH, solid-to-liquid ratio, ionic type, and strength on TC removal was investigated. Adsorption kinetics and isotherms were also determined. HFO after adsorption of TC was analyzed by FTIR and XPS to investigate the adsorption mechanism. The results showed that the adsorption of TC increased from 88.3% to 95% with increasing pH (3.0–7.0) and then decreased. K+ ions had little effect on TC adsorption by HFO. However, Ca2+ and Mg2+ reduced the adsorption of TC on HFO. When the concentrations of Ca2+ and Mg2+ were increased, the inhibitory effect was more obvious. Pseudo-second-order kinetics and the Langmuir model fitted the adsorption process well. The maximum adsorption capacity of TC on HFO reached 99.49 mg·g−1. The adsorption process was spontaneous, endothermic, and increasingly disordered. Combination analysis with FTIR and XPS showed that the mechanism between TC and HFO involved electrostatic interactions, hydrogen interactions, and complexation. Therefore, the environmental behavior of TC could be affected by HFO.

scholarly journals Efficient removal of pharmaceuticals from water using graphene nanoplatelets as adsorbent

2021 ◽  
Vol 8 (1) ◽  
pp. 201076
Author(s):  
Fatin Ahza Rosli ◽  
Haslina Ahmad ◽  
Khairulazhar Jumbri ◽  
Abdul Halim Abdullah ◽  
Sazlinda Kamaruzaman ◽  
...  
Keyword(s):  
Adsorption Process ◽  
Environmental Water ◽  
Graphene Nanoplatelets ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
Solution Ph ◽  
Pharmaceutical Pollutants ◽  
Transmission Electron ◽  
Kinetics And Isotherms

Recently, pharmaceutical pollutants in water have emerged as a global concern as they give threat to human health and the environment. In this study, graphene nanoplatelets (GNPs) were used to efficiently remove antibiotics sulfamethoxazole (SMX) and analgesic acetaminophen (ACM) as pharmaceutical pollutants from water by an adsorption process. GNPs; C750, C300, M15 and M5 were characterized by high-resolution transmission electron microscopy, Raman spectroscopy, X-ray diffraction and Brunauer–Emmett–Teller. The effects of several parameters viz. solution pH, adsorbent amount, initial concentration and contact time were studied. The parameters were optimized by a batch adsorption process and the maximum removal efficiency for both pharmaceuticals was 99%. The adsorption kinetics and isotherms models were employed, and the experimental data were best analysed with pseudo-second kinetic and Langmuir isotherm with maximum adsorption capacity (Q m ) of 210.08 mg g −1 for SMX and 56.21 mg g −1 for ACM. A regeneration study was applied using different eluents; 5% ethanol-deionized water 0.005 M NaOH and HCl. GNP C300 was able to remove most of both pollutants from environmental water samples. Molecular docking was used to simulate the adsorption mechanism of GNP C300 towards SMX and ACM with a free binding energy of −7.54 kcal mol −1 and −5.29 kcal mol −1 , respectively, which revealed adsorption occurred spontaneously.

scholarly journals Studies on the Removal of Cadmium Toxic Metal Ions by Natural Clays from Aqueous Solution by Adsorption Process

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Rajaa Bassam ◽  
Achraf El hallaoui ◽  
Marouane El Alouani ◽  
Maissara Jabrane ◽  
El Hassan El Khattabi ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Adsorption Process ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Toxic Metal ◽  
Ion Concentration ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Solution Ph ◽  
Natural Clays

The aim of this study is the valorization of the Moroccan clays (QC-MC and QC-MT) from the Middle Atlas region as adsorbents for the treatment of water contaminated by cadmium Cd (II) ions. The physicochemical properties of natural clays are characterized by ICP-MS, XRD, FTIR, and SEM techniques. The adsorption process is investigated as a function of adsorbent mass, solution pH, contact time, temperature, and initial Cd (II) ion concentration. The kinetic investigation shows that the adsorption equilibrium of Cd (II) ions by both natural clays is reached after 30 min for QC-MT and 45 min for QC-MC and fits well to a pseudo-second-order kinetic model. The isotherm study is best fitted by a Freundlich model, with the maximum adsorption capacity determined by the linear form of the Freundlich isotherm being 4.23 mg/g for QC-MC and 5.85 mg/g for QC-MT at 25°C. The cadmium adsorption process was thermodynamically spontaneous and exothermic. The regeneration process showed that these natural clays had excellent recycling capacity. Characterization of the Moroccan natural clays before and after the adsorption process through FTIR, SEM, XRD, and EDX techniques confirmed the Cd (II) ion adsorption on the surfaces of both natural clay adsorbents. Overall, the high adsorption capacity of both natural clays for Cd (II) ions removal compared to other adsorbents motioned in the literature indicated that these two natural adsorbents are excellent candidates for heavy metal removal from aqueous environments.

scholarly journals Pristine and Magnetic Kenaf Fiber Biochar for Cd2+ Adsorption from Aqueous Solution

2021 ◽  
Vol 18 (15) ◽  
pp. 7949
Author(s):  
Anwar Ameen Hezam Saeed ◽  
Noorfidza Yub Harun ◽  
Suriati Sufian ◽  
Muhammad Roil Bilad ◽  
Zaki Yamani Zakaria ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Photoelectron Spectroscopy ◽  
Textural Properties ◽  
Ion Concentration ◽  
Solution Temperature ◽  
Maximum Adsorption Capacity ◽  
Magnetic Biochar ◽  
X Ray ◽  
Study Results ◽  
Capacity Surface

Development of strategies for removing heavy metals from aquatic environments is in high demand. Cadmium is one of the most dangerous metals in the environment, even under extremely low quantities. In this study, kenaf and magnetic biochar composite were prepared for the adsorption of Cd2+. The synthesized biochar was characterized using (a vibrating-sample magnetometer VSM), Scanning electron microscopy (SEM), X-ray powder diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). The adsorption batch study was carried out to investigate the influence of pH, kinetics, isotherm, and thermodynamics on Cd2+ adsorption. The characterization results demonstrated that the biochar contained iron particles that help in improving the textural properties (i.e., surface area and pore volume), increasing the number of oxygen-containing groups, and forming inner-sphere complexes with oxygen-containing groups. The adsorption study results show that optimum adsorption was achieved under pH 5–6. An increase in initial ion concentration and solution temperature resulted in increased adsorption capacity. Surface modification of biochar using iron oxide for imposing magnetic property allowed for easy separation by external magnet and regeneration. The magnetic biochar composite also showed a higher affinity to Cd2+ than the pristine biochar. The adsorption data fit well with the pseudo-second-order and the Langmuir isotherm, with the maximum adsorption capacity of 47.90 mg/g.

Preparation of Novel Ag–Si–TiO2 Composite and Research on Its Photocatalytic Degradation of Formaldehyde

2021 ◽  
Vol 13 (3) ◽  
pp. 371-380
Author(s):  
Yongjun Wu ◽  
Nina Xie ◽  
Lu Yu
Keyword(s):  
Photoelectron Spectroscopy ◽  
Removal Rate ◽  
Sol Gel ◽  
Catalytic Performance ◽  
Formaldehyde Concentration ◽  
Order Kinetic ◽  
Solution Ph ◽  
Visible Absorption ◽  
X Ray ◽  
Co Doped

A novel Ag–Si–TiO2 composite was prepared via sol–gel method for removing residual formaldehyde in shiitake mushroom. The structure of Ag–Si–TiO2 composite was characterized by scanning electron microscope (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analyses. Ultraviolet-visible absorption spectroscopy (UV-Vis) and N2 adsorption-desorption tests showed that Ag and Si co-doped decreased the band gap, the Brunauer-Emmett-Teller (BET) specific surface area of the samples increased and the recombination probability of electron-hole pairs (e--h+) reduced. Effect on removal rate of formaldehyde with different Ag-Si co-doped content, formaldehyde concentration and solution pH were investigated, and the results showed that 6.0 wt%Ag-3.0 wt%Si-TiO2 samples had an optimum catalytic performance, and the degradation efficiency reached 96.6% after 40 W 365 nm UV lamp irradiation for 360 min. The kinetics of formaldehyde degradation by Ag–Si–TiO2 composite photocatalyst could be described by Langmuir-Hinshelwood first-order kinetic model.

scholarly journals Efficient and Selective Adsorption of Gold Ions from Wastewater with Polyaniline Modified by Trimethyl Phosphate: Adsorption Mechanism and Application

Polymers ◽  
2019 ◽  
Vol 11 (4) ◽  
pp. 652 ◽  
Author(s):  
Wang ◽  
Zhao ◽  
Wang ◽  
Zhang ◽  
Zhang
Keyword(s):  
Adsorption Capacity ◽  
Adsorption Process ◽  
Selective Adsorption ◽  
Interaction Mechanism ◽  
Single Layer ◽  
Phosphate Adsorption ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Trimethyl Phosphate ◽  
Selective Recovery

The selective recovery of gold from wastewater is necessary because it is widely used in various fields. In this study, a new polymeric adsorbent (TP-AFC) was prepared by modifying polyaniline with trimethyl phosphate for the selective recovery of gold from wastewater. Bath experiments were carried out to explore the adsorption capacity and mechanism. The optimum pH of adsorption is 4. The adsorption equilibrium is reached at 840 min. The maximum adsorption capacity is 881 mg/g and the adsorption was a spontaneous endothermic process. The adsorption process fitted well with pseudo second-order kinetic and the Langmuir-models. The single-layer chemisorption governed the adsorption process. In addition, the application in wastewater indicated that the interfering ions had no effect on the adsorption of gold ions. TP-AFC has good selectivity. The interaction mechanism was mainly ion exchange and complexation. In general, TP-AFC was successfully prepared and has an excellent future in practical application.

scholarly journals Removal of Cesium and Strontium From Radioactive Wastewater by Prussian Blue Nanorods

2022 ◽  
Author(s):  
Chuqing Yao ◽  
Yaodong Dai ◽  
Shuquan Chang ◽  
Haiqian Zhang
Keyword(s):  
Prussian Blue ◽  
Photoelectron Spectroscopy ◽  
Adsorption Process ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Radioactive Wastewater ◽  
Pseudo Second Order ◽  
Co Precipitation ◽  
Solvothermal Methods

Abstract In this work, novel Prussian blue tetragonal nanorods were prepared by template-free solvothermal methods for removal of radionuclide Cs and Sr. It was worth that Prussian blue nanorods exhibited the better adsorption performance than co-precipitation PB or Prussian blue analogue composites. Thermodynamic analysis implied that adsorption process was spontaneous and endothermic which was described well with Langmuir isotherm and pseudo-second-order equation, the maximum adsorption capacity of PB nanorod was estimated to be 194.26 mg g-1 and 256.62 mg g-1 for Cs+ and Sr2+. The adsorption mechanism of Cs+ and Sr2+ was studied by X-ray photoelectron spectroscopy, X-ray diffraction and 57Fe Mössbaure spectroscopy, the results revealed that Cs+ entered in PB crystal to generate a new phase, the most of Sr2+ was trapped in internal crystal and the other exchanged Fe2+. Furthermore, the effect of co-existing ions and pH for PB adsorption process were also investigated. The results suggest that PB nanorods were outstanding candidate for removal of Cs+ and Sr2+ from radioactive wastewater.

scholarly journals Treatment of effluent from fertilizer industry by adsorption on willow sawdust-removal of Ni(II) and Cd(II) from the effluent

2021 ◽  
pp. 1-12
Author(s):  
Raafia Najam ◽  
Syed Muzaffar Ali Andrabi
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
The World ◽  
Pseudo Second Order ◽  
Almost All ◽  
Willow Tree

Sawdust of willow has been investigated as an adsorbent for the removal of Ni(II), and Cd(II) ions from aqueous solution. Since willow tree is widely grown in almost all parts of Kashmir, it can be a common most easily available, sustainable, low cost adsorbent for the treatment of wastewaters in this part of the world where growing industrialization is affecting water quality like elsewhere in the world. Therefore, it is worthwhile to investigate the potential of sawdust of willow tree as an adsorbent for the removal of Ni(II) and Cd(II) ions from aqueous solution as a first step. Batch experiments were conducted to study the effect of some parameters such as contact time, initial concentration of metal ions, solution pH and temperature. Langmuir and Freundlich models were employed for the mechanistic analysis of experimental data obtained. Results reveal that in our system adsorption follows the Langmuir isotherm. The maximum adsorption capacity of Ni(II) and Cd(II) were found to be 7.98 and 7.11 mg/g respectively at optimum conditions. The pseudo-first-order and pseudo-second-order models were employed for kinetic analysis of adsorption process. The adsorption process follows pseudo-second-order kinetics. The efficacy of the adsorbent in the treatment of effluent from fertilizer factory has been investigated and the results have been found encouraging.

scholarly journals Porous Multifunctional Phenylcarbamoylated-β-Cyclodextrin Polymers for Rapid Removal of Organic Pollutants

2021 ◽  
Author(s):  
He Wang ◽  
Congzhi Liu ◽  
Xiaofei Ma ◽  
Yong Wang
Keyword(s):  
Organic Contaminants ◽  
Adsorption Process ◽  
Removal Rate ◽  
Pollutant Removal ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Monolayer Adsorption ◽  
Pseudo Second Order ◽  
Rapid Removal ◽  
Cyclodextrin Polymers

Abstract In this work, a series of porous multifunctional cyclodextrin (CD) polymers were fabricated using tetrafluoroterephthalonitrile (TFTPN) as the rigid crosslinker for the condensation of different functional phenylcarbamoylated-β-cyclodextrin derivatives to afford three preliminary polymerized adsorption materials such as poly nitrophenylcarbamoylated-β-cyclodextrin (NO2-CDP), poly trifluoromethylphenylcarbamoylated-β-cyclodextrin (F-CDP), poly chlorophenylcarbamoylated-β-cyclodextrin polymers (Cl-CDP) and a mix β- cyclodextrin polymer (X-CDP) prepared via a secondary crosslinking procedure of the above three materials. The X-CDP preparation process connects the `pre-formed nanoparticles and increases the presence of linkers inside the particles. At the same time, X-CDP exhibited porous structure with various functional groups such as nitro, chlorine, fluorine and hydroxyl. Those special characteristics render this material with good adsorption ability towards various pollutants in water, including tetracycline, ibuprofen, dichlorophenol, norfloxacin, bisphenol A, naphthol. Especially the maximum adsorption capacity for tetracycline at equilibrium reached 230.15 mg·g− 1, which is competitive with the adsorption capacities of other polysaccharides adsorbents. X-CDP removed organic contaminants much more quickly than other adsorbents, reaching almost ~ 95% of its equilibrium in only 30 s. The main adsorption process of the pollutants by X-CDP fitted the pseudo-second-order kinetic and Langmuir isotherm well, indicating that the adsorption process is monolayer adsorption. Moreover, X-CDP possessed the good reusability where the pollutant removal rate was only reduced 8.3% after five cycles.

scholarly journals The Adsorption of Methylene Blue by an Amphiphilic Block Co-Poly(Arylene Ether Nitrile) Microsphere-Based Adsorbent: Kinetic, Isotherm, Thermodynamic and Mechanistic Studies

Nanomaterials ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1356 ◽  
Author(s):  
Xuefei Zhou ◽  
Mingzhen Xu ◽  
Lingling Wang ◽  
Xiaobo Liu
Keyword(s):  
Methylene Blue ◽  
Adsorption Process ◽  
Selective Adsorption ◽  
Modern Society ◽  
Influential Factors ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Cationic Dye ◽  
Solution Ph ◽  
Arylene Ether

Dye pollution is a serious problem in modern society. We desired to develop an efficient adsorbent for the decontamination of discharged dyes. In this work, the polymeric microspheres derived from a kind of amphiphilic block of co-poly(arylene ether nitrile) (B-b-S-P) were prepared on the basis of “oil-in-water” (O/W) microemulsion method. The B-b-S-P microspheres were found competent to remove the cationic dye, methylene blue (MB); and various influential factors, such as contact time, initial concentration, solution pH and temperature were investigated. Results indicated that the maximum adsorption capacity of B-b-S-P microspheres for MB was 119.84 mg/g at 25 °C in neutral conditions. Adsorption kinetics and isotherm dates were well fitted to a pseudo-second-order kinetic model and the Langmuir isotherm model, and thermodynamic parameters implied that the adsorption process was endothermic. The B-b-S-P microspheres also exhibited a highly selective adsorption for cationic dye MB, even in the presence of anionic dye methyl orange (MO). In addition, the possible adsorption mechanism was studied, suggesting that the electrostatic interaction and π–π interaction could be the main force in the adsorption process.

Sign in / Sign up

Export Citation Format

Share Document