scholarly journals Novel Biobased Polyamide 410/Polyamide 6/CNT Nanocomposites

Polymers ◽  
2018 ◽  
Vol 10 (9) ◽  
pp. 986 ◽  
Author(s):  
Itziar Otaegi ◽  
Nora Aramburu ◽  
Alejandro Müller ◽  
Gonzalo Guerrica-Echevarría
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus ◽  
Polyamide 6 ◽  
Multiwall Carbon Nanotube ◽  
Scanning Calorimetry ◽  
Melt Mixing ◽  
Good Dispersion ◽  
Maximum Conductivity ◽  
Twin Screw ◽  
Potential Applications

Biobased polyamide 410 (PA410)/multiwall carbon nanotube (CNT) nanocomposites (NCs) were obtained by melt-mixing in a twin screw extruder a Polyamide 6 (PA6)-based masterbatch (with 15 wt % CNT content) with neat PA410. Directly mixed PA410/CNT NCs were also obtained for comparison purposes. Transmision Electronic Microscopy (TEM) observation and conductivity measurements demonstrated that a good dispersion of CNTs was obtained, which was probably induced by the full miscibility between PA410 and PA6 (in the concentration range employed here), as ascertained by Differential Scanning Calorimetry (DSC) tests. As a result, the PA410/PA6/CNT NCs showed superior mechanical behaviour (≈10% Young’s modulus increase with a 4 wt % CNT content) than the binary PA410/CNT NCs (≈5% Young’s modulus increase with a 6 wt % CNT content), as well as superior electrical behaviour, with maximum conductivity values of approximately three orders of magnitude higher than in the binary PA410/CNT system, and lower percolation threshold values (0.65 wt % CNT content vs. 3.98 wt % CNT). The good dispersion and enhanced mechanical and electrical properties of these novel biobased nanocomposites, broadens their potential applications, such as electrical and electronics (E&E) or automotive industries.

Effect of Microcrystalline Cellulose from Banana Stem Fiber on Mechanical Properties and Crystallinity of PLA Composite Films

2011 ◽  
Vol 695 ◽  
pp. 170-173 ◽  
Author(s):  
Voravadee Suchaiya ◽  
Duangdao Aht-Ong
Keyword(s):  
Tensile Strength ◽  
Young’S Modulus ◽  
Microcrystalline Cellulose ◽  
Young's Modulus ◽  
Agricultural Waste ◽  
Composite Films ◽  
Sem Image ◽  
Biocomposite Films ◽  
Twin Screw ◽  
Banana Stem

This work focused on the preparation of the biocomposite films of polylactic acid (PLA) reinforced with microcrystalline cellulose (MCC) prepared from agricultural waste, banana stem fiber, and commercial microcrystalline cellulose, Avicel PH 101. Banana stem microcrystalline cellulose (BS MCC) was prepared by three steps, delignification, bleaching, and acid hydrolysis. PLA and two types of MCC were processed using twin screw extruder and fabricated into film by a compression molding. The mechanical and crystalline behaviors of the biocomopsite films were investigated as a function of type and amount of MCC. The tensile strength and Young’s modulus of PLA composites were increased when concentration of MCC increased. Particularly, banana stem (BS MCC) can enhance tensile strength and Young’s modulus of PLA composites than the commercial MCC (Avicel PH 101) because BS MCC had better dispersion in PLA matrix than Avicel PH 101. This result was confirmed by SEM image of fractured surface of PLA composites. In addition, XRD patterns of BS MCC/PLA composites exhibited higher crystalline peak than that of Avicel PH 101/PLA composites

A UNIQUE APPROACH TO EXPERIMENTAL CHARACTERIZATION OF A THERMOSETTING POLYMER MATRIX FOR ICME FRAMEWORKS

2021 ◽  
Author(s):  
MICHAEL N. OLAYA ◽  
SAGAR PATIL ◽  
GREGORY M. ODEGARD ◽  
MARIANNA MAIARÙ
Keyword(s):  
Tensile Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Cure Kinetics ◽  
Image Correlation ◽  
Scanning Calorimetry ◽  
Mixing Ratios ◽  
Fitting Procedure ◽  
Amine Content

A novel approach for characterization of thermosetting epoxy resins as a function of the degree of cure is presented. Density, cure kinetics, tensile strength, and Young’s modulus are experimentally characterized across four mixing ratios of DGEBF/DETDA epoxy. Dynamic differential scanning calorimetry (DSC) is used to characterize parameters for a Prout-Thompkins kinetic model unique to each mixing ratio case through a data fitting procedure. Tensile strength and Young’s modulus are then characterized using stress-strain data extracted from quasi-static, uniaxial tension tests at room temperature. Strains are measured with the 2-D digital image correlation (DIC) optical strain measurement technique. Strength tends to increase as amine content use in the formulation increases. The converse trend is observed for Young’s modulus. Density measurements also reveal an inverse relationship with amine content.

Thermal and Tensile Properties of PP Nanocomposite Blends

2008 ◽  
Vol 47-50 ◽  
pp. 21-24
Author(s):  
C. Rosales ◽  
V. Contreras ◽  
M. Matos ◽  
R. Perera ◽  
N. Villarreal ◽  
...  
Keyword(s):  
Tensile Modulus ◽  
Polyamide 6 ◽  
Dispersed Phase ◽  
Scanning Calorimetry ◽  
Binary Blend ◽  
Polyethylene Blends ◽  
Metallocene Polyethylene ◽  
The Matrix ◽  
Twin Screw ◽  
Layered Clay

Polypropylene/polyamide-6 and polypropylene/metallocene polyethylene blends containing 2.5 phr of organophilic modified montmorillonite were prepared in a twin-screw extruder followed by injection molding. In order to compare, blends without layered clay were also made. Styreneethylene- butylene-styrene copolymer and polypropylene grafted with anhydride maleic were used as compatibilizers in the ternary blends and in the PP nanocomposite preparation, respectively. The presence of tactoids, intercalated and exfoliated structures was observed by TEM in some of the samples containing layered clay and modified PP materials. Results showed that the compatibilized blends prepared without clay are tougher than those prepared with the nanocomposite of PP as the matrix phase and no significant changes in tensile moduli were observed between them. However, the binary blend with a nanocomposite of PP as matrix and metallocene polyethylene exhibited better tensile toughness and lower tensile modulus, than those prepared with a nanocomposite of PP and polyamide-6 as dispersed phase. These results are related to the degree of clay dispersion in the PP and to the type of morphology developed in the different blends. Differential scanning calorimetry (DSC) showed that blends with a finer and homogeneously dispersed morphology determined by SEM, the PA component exhibited fractionated crystallization exotherms in the temperature range of 159-185°C. Also, nucleation of the PP component by PA phase and/or the layered clay was observed in the blends with PA as dispersed phase.

scholarly journals Enhancement of the Thermomechanical Properties of a Fly Ash- and Carbon Black-Filled Polyvinyl Chloride Composite by Using Epoxidized Soybean Oil as a Secondary Bioplasticizer

2018 ◽  
Vol 2018 ◽  
pp. 1-8
Author(s):  
Toan Duy Nguyen ◽  
Chinh Thuy Nguyen ◽  
Van Thanh Thi Tran ◽  
Giang Vu Nguyen ◽  
Hai Viet Le ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Fly Ash ◽  
Carbon Black ◽  
Soybean Oil ◽  
Young’S Modulus ◽  
Polyvinyl Chloride ◽  
Young's Modulus ◽  
Epoxidized Soybean Oil ◽  
Melt Mixing ◽  
Elongation At Break

Plasticized polyvinyl chloride (PVC) was fabricated using epoxidized soybean oil (ESBO) as a secondary bioplasticizer with dioctyl phthalate (DOP). The PVC/MFA/CB composites were prepared by melt mixing of the plasticized PVC with modified fly ash (MFA), carbon black N330 (CB), and polychloroprene (CR) in a Haake Rheomix mixer using a rotation speed of 50 rpm at 175°C for 6 min and then compressed by Toyoseiki pressure machine under 15 MPa. The effect of ESBO content on morphology, melt viscosity, tensile properties, and flame retardancy of PVC/MFA/CB composites was investigated. The obtained results showed that the incorporation of ESBO has significantly enhanced the processing ability, Young’s modulus, tensile strength, and elongation at break of the PVC/MFA/CB composites. The torque of PVC/MFA/CB composites was increased to approximately 12% when 50 wt% of DOP was replaced by ESBO. When ESBO was 20 wt% in comparison with DOP weight, the elongation at break, tensile strength, and Young’s modulus of the composites were increased to 48%, 24%, and 4.5%, respectively. Correspondingly, thermogravimetric analysis results confirmed that ESBO had improved the thermostability of the PVC composites. The ESBO have potential as a secondary bioplasticizer replacement material for DOP owing to their better thermomechanical stability.

Mathematical Analysis of MWCNT Based Aluminum Alloy Metal Matrix Composite

2016 ◽  
Vol 852 ◽  
pp. 98-103
Author(s):  
P.S. Samuel Ratna Kumar ◽  
S. John Alexis ◽  
D.S. Robinson Smart
Keyword(s):  
Aluminium Alloy ◽  
Metal Matrix Composite ◽  
Young’S Modulus ◽  
Matrix Composite ◽  
Metal Matrix ◽  
Young's Modulus ◽  
High Strength ◽  
Multiwall Carbon Nanotube ◽  
Aspect Ratios ◽  
Marine Applications

The interest in Multiwall Carbon Nanotube (MWCNT) as reinforcement for Aluminium alloy has been growing considerably because of its significant properties such as high Strength, elastic modulus, flexibility and high aspect ratios which makes the combination for being used in aerospace, automobile and marine applications. This work mainly focuses on the theoretical analysis of Strength and Young’s modulus of MWCNT addition with Aluminium 5083 metal matrix composite for different compositions like 1, 1.25, 1.5 and 1.75 weight %, representing that the MWCNT are effective reinforcement. The predicted value shows that, the addition of MWCNT is increasing the Young’s modulus and Strength for the composite compared to the AA5083 (Aluminium alloy).

Dynamic Vulcanization of NR/PCL Blends: Effect of Rotor Speed on Morphology, Tensile Properties and Tension Set

2019 ◽  
Vol 798 ◽  
pp. 337-342 ◽  
Author(s):  
Chanchai Thongpin ◽  
Theeraphat Tanprasert
Keyword(s):  
Young’S Modulus ◽  
Shear Force ◽  
Young's Modulus ◽  
Tensile Behavior ◽  
Rotor Speed ◽  
Melt Mixing ◽  
Dynamic Vulcanization ◽  
Strain Behavior ◽  
Phase Size ◽  
Sem Micrograph

This work aimed to study effect of rotor speed during melt mixing of natural rubber/polycaprolactone (NR/PCL) on the morphology which controls mechanical properties of dynamic vulcanizate using Luperox101 as a curing agent in NR component. The rotor speeds at 60 and 80 rpm were compared. The morphology of NR/PCL vulcanizates elucidated from SEM micrograph showed that the vulcanizates exhibited NR paticles dispersed in PCL matrix. In addition, the phase size of dispersed NR should be smaller with increasing rotor speed due to the increased shear force. This large PCL domain induced stronger strain hardening in stress-strain behavior under tension. This behavior is closed to tensile behavior of PCL and appeared at the vulcanizates. In terms of modulus, Young’s modulus was concentrated and reported. The lower degradation of PCL phase during melt mixing in the vulcanizates prepared from melt mixing at rotor speed of 60 rpm was responsible for higher Young‘s modulus than that prepared from rotor speed of 80 rpm. The tension set of NR/PCL vulcanizates prepared with rotor speed of 60 was higher than that with rotor speed of 80 rpm. It was suggested by Nakason et.al. [1] that the tension set of vulcanizates should be lower than 50 % so that they could be applied for thermoplastic vulcanizates. In this system, tension set values of the vulcanizates containing PCL 30-45 wt.% were lower than 50% in both rotor speed conditions.

scholarly journals Polyamide 6/Poly(vinylidene fluoride) Blend-Based Nanocomposites with Enhanced Rigidity: Selective Localization of Carbon Nanotube and Organoclay

Polymers ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 184 ◽  
Author(s):  
Hung-Ming Lin ◽  
Kartik Behera ◽  
Mithilesh Yadav ◽  
Fang-Chyou Chiu
Keyword(s):  
Carbon Nanotube ◽  
Vinylidene Fluoride ◽  
Domain Size ◽  
Polyamide 6 ◽  
Vital Role ◽  
Scanning Electron Micrographs ◽  
Scanning Calorimetry ◽  
Poly Vinylidene Fluoride ◽  
Twin Screw ◽  
Diffraction Patterns

Polyamide 6 (PA6)/poly(vinylidene fluoride) (PVDF) blend-based nanocomposites were successfully prepared using a twin screw extruder. Carbon nanotube (CNT) and organo-montmorillonite (30B) were used individually and simultaneously as reinforcing nanofillers for the immiscible PA6/PVDF blend. Scanning electron micrographs showed that adding 30B reduced the dispersed domain size of PVDF in the blend, and CNT played a vital role in the formation of a quasi-co-continuous PA6-PVDF morphology. Transmission electron microscopy observation revealed that both fillers were mainly located in the PA6 matrix phase. X-ray diffraction patterns showed that the presence of 30B facilitated the formation of γ-form PA6 crystals in the composites. Differential scanning calorimetry results indicated that the crystallization temperature of PA6 increased after adding CNT into the blend. The inclusion of 30B retarded PA6 nucleation (γ-form crystals growth) upon crystallization. The Young’s and flexural moduli of the blend increased after adding CNT and/or 30B. 30B exhibited higher enhancing efficiency compared with CNT. The composite with 2 phr 30B exhibited 21% higher Young’s modulus than the blend. Measurements of the rheological properties confirmed the development of a pseudo-network structure in the CNT-loaded composites. Double percolation morphology in the PA6/PVDF blend was achieved with the addition of CNT.

Ab initio investigation of the Young's modulus of polyamide-6

2002 ◽  
Vol 91 (1) ◽  
pp. 32-38 ◽  
Author(s):  
Anik Peeters ◽  
C. Van Alsenoy ◽  
F. Bartha ◽  
F. Bogár ◽  
M.-L. Zhang ◽  
...  
Keyword(s):  
Ab Initio ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Polyamide 6

scholarly journals Properties of Raphia Palm Interspersed Fibre Filled High Density Polyethylene

2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
Henry C. Obasi
Keyword(s):  
Particle Size ◽  
Young’S Modulus ◽  
High Density Polyethylene ◽  
Young's Modulus ◽  
High Density ◽  
Screw Extruder ◽  
Elongation At Break ◽  
Twin Screw ◽  
Partial Degradation ◽  
Different Levels

Blends of nonbiodegradable and biodegradable polymers can promote a reduction in the volume of plastic waste when they undergo partial degradation. In this study, properties of raphia palm interspersed fibre (RPIF) filled high density polyethylene (HDPE) have been investigated at different levels of filler loadings, 0 to 60 wt.%. Maleic anhydride-graft polyethylene was used as a compatibilizer. Raphia palm interspersed fibre was prepared by grinding and sieved to a particle size of 150 µm. HDPE blends were prepared in a corotating twin screw extruder. Results showed that the tensile strength and elongation at break of the blends decreased with increase in RPI loadings and addition of MA-g-PE was found to improve these properties. However, the Young’s modulus increased with increase in the amount of RPI into HDPE and compatibilization further increased the Young’s modulus. The water absorption indices and weight loss for RPI/HDPE composites were found to increase with RPI loadings but were decreased on addition of MA-g-PE.

Influence of annealing on microstructure & molecular orientation, thermal behaviour, mechanical properties and their correlations of uniaxially drawn iPP thin film

e-Polymers ◽  
2008 ◽  
Vol 8 (1) ◽  
Author(s):  
Sayant Saengsuwan
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Tensile Strength ◽  
Young’S Modulus ◽  
Thermal Behaviour ◽  
Annealing Time ◽  
Molecular Orientation ◽  
Young's Modulus ◽  
Crystal Thickness ◽  
Scanning Calorimetry

AbstractThe influence of annealing on the microstructure and molecular orientation, thermal behaviour and mechanical properties of uniaxially drawn iPP thin film was studied by wide-angle X-ray diffraction, differential scanning calorimetry and tensile testing, respectively. The correlations of mechanical and microstructural properties of annealed films were also examined. The transformation of smectic phase of iPP to the α-form was more pronounced with increasing annealing time and temperature. The true and apparent crystallinities and crystal thickness were strongly enhanced with annealing time and temperature. The relative molecular orientation tended to increase with annealing time. These results caused the significant improvement of modulus and tensile strength of the annealed films in both machine (MD) and transverse (TD) directions. The increases in MD-Young’s modulus and MD-tensile strength were well correlated with the increase in true crystallinity obtained in equatorial scans. Some relationship between the increase in crystal thickness and the increase in Young’s modulus in both MD and TD directions was also found.

Sign in / Sign up

Export Citation Format

Share Document