scholarly journals Metalenses Based on Symmetric Slab Waveguide and c-TiO2: Efficient Polarization-Insensitive Focusing at Visible Wavelengths

Nanomaterials ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 699 ◽  
Author(s):  
Yaoyao Liang ◽  
Zhongchao Wei ◽  
Jianping Guo ◽  
Faqiang Wang ◽  
Hongyun Meng ◽  
...  
Keyword(s):  
Berry Phase ◽  
Incident Light ◽  
Visible Spectrum ◽  
Slab Waveguide ◽  
Optical Elements ◽  
Polarization Insensitive ◽  
Wavefront Shaping ◽  
Visible Wavelengths ◽  
532 Nm ◽  
Good Agreement

A key goal of metalens research is to achieve wavefront shaping of light using optical elements with thicknesses on the order of the wavelength. Here we demonstrate ultrathin highly efficient crystalline titanium dioxide metalenses at blue, green, and red wavelengths (λ0 = 453 nm, 532 nm, and 633 nm, respectively) based on symmetric slab waveguide theory. These metalenses are less than 488 nm-thick and capable of focusing incident light into very symmetric diffraction-limited spots with strehl ratio and efficiency as high as 0.96 and 83%, respectively. Further quantitative characterizations about metalenses’ peak focusing intensities and focal spot sizes show good agreement with theoretical calculation. Besides, the metalenses suffer only about 10% chromatic deviation from the ideal spots in visible spectrum. In contrast with Pancharatnam–Berry phase mechanism, which limit their incident light at circular polarization, the proposed method enables metalenses polarization-insensitive to incident light.

Polarization-insensitive wavefront shaping using the Pancharatnam–Berry phase

2019 ◽  
Vol 44 (22) ◽  
pp. 5517 ◽  
Author(s):  
Chandroth P. Jisha ◽  
Stefan Nolte ◽  
Alessandro Alberucci
Keyword(s):  
Berry Phase ◽  
Polarization Insensitive ◽  
Wavefront Shaping

scholarly journals Polarization-insensitive 3D conformal-skin metasurface cloak

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
He-Xiu Xu ◽  
Guangwei Hu ◽  
Yanzhao Wang ◽  
Chaohui Wang ◽  
Mingzhao Wang ◽  
...  
Keyword(s):  
3D Printing ◽  
Incident Light ◽  
Three Dimensional ◽  
Free Form ◽  
Polarization Insensitive ◽  
Wavelength Scale ◽  
First Time ◽  
Printing Techniques ◽  
Flat Ground ◽  
Good Agreement

AbstractElectromagnetic metasurface cloaks provide an alternative paradigm toward rendering arbitrarily shaped scatterers invisible. Most transformation-optics (TO) cloaks intrinsically need wavelength-scale volume/thickness, such that the incoming waves could have enough long paths to interact with structured meta-atoms in the cloak region and consequently restore the wavefront. Other challenges of TO cloaks include the polarization-dependent operation to avoid singular parameters of composite cloaking materials and limitations of canonical geometries, e.g., circular, elliptical, trapezoidal, and triangular shapes. Here, we report for the first time a conformal-skin metasurface carpet cloak, enabling to work under arbitrary states of polarization (SOP) at Poincaré sphere for the incident light and arbitrary conformal platform of the object to be cloaked. By exploiting the foundry three-dimensional (3D) printing techniques to fabricate judiciously designed meta-atoms on the external surface of a conformal object, the spatial distributions of intensity and polarization of its scattered lights can be reconstructed exactly the same as if the scattering wavefront were deflected from a flat ground at any SOP, concealing targets under polarization-scanning detections. Two conformal-skin carpet cloaks working for partial- and full-azimuth plane operation are respectively fabricated on trapezoid and pyramid platforms via 3D printing. Experimental results are in good agreement with numerical simulations and both demonstrate the polarization-insensitive cloaking within a desirable bandwidth. Our approach paves a deterministic and robust step forward to the realization of interfacial, free-form, and full-polarization cloaking for a realistic arbitrary-shape target in real-world applications.

scholarly journals Broadband high-efficiency dielectric metasurfaces for the visible spectrum

2016 ◽  
Vol 113 (38) ◽  
pp. 10473-10478 ◽  
Author(s):  
Robert C. Devlin ◽  
Mohammadreza Khorasaninejad ◽  
Wei Ting Chen ◽  
Jaewon Oh ◽  
Federico Capasso
Keyword(s):  
High Performance ◽  
High Efficiency ◽  
Numerical Aperture ◽  
Optical Loss ◽  
Visible Spectrum ◽  
Optical Element ◽  
Atomic Layer ◽  
Optical Elements ◽  
Layer Deposition ◽  
Visible Wavelengths

Metasurfaces are planar optical elements that hold promise for overcoming the limitations of refractive and conventional diffractive optics. Original dielectric metasurfaces are limited to transparency windows at infrared wavelengths because of significant optical absorption and loss at visible wavelengths. Thus, it is critical that new materials and nanofabrication techniques be developed to extend dielectric metasurfaces across the visible spectrum and to enable applications such as high numerical aperture lenses, color holograms, and wearable optics. Here, we demonstrate high performance dielectric metasurfaces in the form of holograms for red, green, and blue wavelengths with record absolute efficiency (>78%). We use atomic layer deposition of amorphous titanium dioxide with surface roughness less than 1 nm and negligible optical loss. We use a process for fabricating dielectric metasurfaces that allows us to produce anisotropic, subwavelength-spaced dielectric nanostructures with shape birefringence. This process is capable of realizing any high-efficiency metasurface optical element, e.g., metalenses and axicons.

scholarly journals Microfabrication and Surface Functionalization of Soda Lime Glass through Direct Laser Interference Patterning

Nanomaterials ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 129
Author(s):  
Marcos Soldera ◽  
Sabri Alamri ◽  
Paul Alexander Sürmann ◽  
Tim Kunze ◽  
Andrés Fabián Lasagni
Keyword(s):  
Laser Radiation ◽  
Surface Functionalization ◽  
Incident Light ◽  
Chemical Properties ◽  
Visible Spectrum ◽  
Soda Lime ◽  
Soda Lime Glass ◽  
Textured Surfaces ◽  
Aspect Ratios ◽  
Direct Laser

All-purpose glasses are common in many established and emerging industries, such as microelectronics, photovoltaics, optical components, and biomedical devices due to their outstanding combination of mechanical, optical, thermal, and chemical properties. Surface functionalization through nano/micropatterning can further enhance glasses’ surface properties, expanding their applicability into new fields. Although laser structuring methods have been successfully employed on many absorbing materials, the processability of transparent materials with visible laser radiation has not been intensively studied, especially for producing structures smaller than 10 µm. Here, interference-based optical setups are used to directly pattern soda lime substrates through non-lineal absorption with ps-pulsed laser radiation in the visible spectrum. Line- and dot-like patterns are fabricated with spatial periods between 2.3 and 9.0 µm and aspect ratios up to 0.29. Furthermore, laser-induced periodic surface structures (LIPSS) with a feature size of approximately 300 nm are visible within these microstructures. The textured surfaces show significantly modified properties. Namely, the treated surfaces have an increased hydrophilic behavior, even reaching a super-hydrophilic state for some cases. In addition, the micropatterns act as relief diffraction gratings, which split incident light into diffraction modes. The process parameters were optimized to produce high-quality textures with super-hydrophilic properties and diffraction efficiencies above 30%.

scholarly journals Metalens Eyepiece for 3D Holographic Near-Eye Display

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1920
Author(s):  
Chang Wang ◽  
Zeqing Yu ◽  
Qiangbo Zhang ◽  
Yan Sun ◽  
Chenning Tao ◽  
...  
Keyword(s):  
Light Field ◽  
Three Dimensional ◽  
Fresnel Diffraction ◽  
Virtual Image ◽  
Display Devices ◽  
Computer Generated Holography ◽  
Wavefront Shaping ◽  
3D Scene ◽  
Optimum Solution ◽  
532 Nm

Near-eye display (NED) systems for virtual reality (VR) and augmented reality (AR) have been rapidly developing; however, the widespread use of VR/AR devices is hindered by the bulky refractive and diffractive elements in the complicated optical system as well as the visual discomfort caused by excessive binocular parallax and accommodation-convergence conflict. To address these problems, an NED system combining a 5 mm diameter metalens eyepiece and a three-dimensional (3D), computer-generated holography (CGH) based on Fresnel diffraction is proposed in this paper. Metalenses have been extensively studied for their extraordinary capabilities at wavefront shaping at a subwavelength scale, their ultrathin compactness, and their significant advantages over conventional lenses. Thus, the introduction of the metalens eyepiece is likely to reduce the issue of bulkiness in NED systems. Furthermore, CGH has typically been regarded as the optimum solution for 3D displays to overcome limitations of binocular systems, since it can restore the whole light field of the target 3D scene. Experiments are carried out for this design, where a 5 mm diameter metalens eyepiece composed of silicon nitride anisotropic nanofins is fabricated with diffraction efficiency and field of view for a 532 nm incidence of 15.7% and 31°, respectively. Furthermore, a novel partitioned Fresnel diffraction and resample method is applied to simulate the wave propagations needed to produce the hologram, with the metalens capable of transforming the reconstructed 3D image into a virtual image for the NED. Our work combining metalens and CGH may pave the way for portable optical display devices in the future.

scholarly journals Polarization-Insensitive Metalenses at Visible Wavelengths

Nano Letters ◽  
2016 ◽  
Vol 16 (11) ◽  
pp. 7229-7234 ◽  
Author(s):  
M. Khorasaninejad ◽  
A. Y. Zhu ◽  
C. Roques-Carmes ◽  
W. T. Chen ◽  
J. Oh ◽  
...  
Keyword(s):  
Polarization Insensitive ◽  
Visible Wavelengths

scholarly journals ERROR ANALYSIS OF THE DISPERSION-COMPENSATED WIDE-BAND POLARIZATION SAGNAC INTERFEROMETER

2020 ◽  
Vol XLIII-B1-2020 ◽  
pp. 621-625
Author(s):  
J. Zhu ◽  
K. Zong ◽  
F. Goudail ◽  
N. Zhang ◽  
X. Hou
Keyword(s):  
Diffraction Efficiency ◽  
Incident Light ◽  
Wide Band ◽  
Reconstruction Error ◽  
Optical Elements ◽  
Blazed Grating ◽  
Interference Fringes ◽  
Splitting Ratio ◽  
Imaging Polarimetry ◽  
Modulation Degree

Abstract. Imaging polarimetry can obtain two-dimensional intensity distribution information and its corresponding states of polarization from the target simultaneously. Sagnac polarization imaging interferometer is one of the typical channeled polarimetry technologies. By splitting the incident light through the triangular optical structure, the polarization information of the target is modulated into the interference fringes and can be obtained by the demodulation algorithm. The non-ideal optical elements in the system will cause reconstruction errors. This article analyses several factors that affect the measurement accuracy, including the splitting ratio of polarization beam splitter and the diffraction efficiency of the blazed grating. We derive the modified intensity formula and obtain interference patterns through numerical simulations. By calculating the modulation degree of interference fringes and reconstruction error under different non-ideal parameters, we have come to the conclusion that to meet the requirement of modulation degree > 0.5 and reconstruction error < 10%, the beam splitting ratio of the PBS should be α < 1.22. The diffraction efficiency ratio of s-polarization to p-polarization of the blazed grating should be ηs/ηp > 0.83, and the first-order diffraction efficiency should be η1 > 79%.

Effect of Focusing Plane on Laser Blow-off Shock Waves from Confined Aluminum and Copper Foils

2021 ◽  
Author(s):  
Nagaraju Guthikonda ◽  
Sai Shiva S ◽  
E. Manikanta ◽  
Kameswari P S L D ◽  
V. R. Ikkurthi ◽  
...  
Keyword(s):  
Laser Energy ◽  
Plasma Temperature ◽  
Laser Pulses ◽  
Ambient Air ◽  
Rear Side ◽  
Hydrodynamic Simulations ◽  
Enhanced Absorption ◽  
532 Nm ◽  
Lower Plasma Density ◽  
Good Agreement

Abstract We present results on the dynamics of laser-induced blow-off shockwave generation from the rear side of 20 µm thick aluminum and copper foil confined with a glass (BK7) substrate. These foils are irradiated by 10 ns, 532 nm laser pulses of energy 25 – 200 mJ corresponding to the intensity range 0.2 – 10 GW/cm2. The plasma temperature at the glass-foil interface is observed to play an important role in the coupling of laser energy to the foil. From our experiments and 1D hydrodynamic simulations, we confirm that moving the glass-foil interface away from the focal plane led to (a) enhanced absorption of the laser beam by the foil resulting in ~ 30 % higher blow-off shock velocities (b) significant changes in the material ejection in terms of increased blow-off mass of the foil (c) lower plasma density and temperatures. The material ejection as well as blow-off shock velocity is higher for Al compared to Cu. The simulated shock evolution in ambient air shows a reasonably good agreement with the experimental results.

scholarly journals Phase-Shift Optimization in AA/PVA Photopolymers by High-Frequency Pulsed Laser

Polymers ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 1887
Author(s):  
Daniel Puerto ◽  
Sergi Gallego ◽  
Jorge Francés ◽  
Andrés Márquez ◽  
Inmaculada Pascual ◽  
...  
Keyword(s):  
Phase Shift ◽  
High Frequency ◽  
Large Scale ◽  
Pulsed Laser ◽  
Laser Exposure ◽  
Continuous Laser ◽  
Frequency Limit ◽  
Optical Elements ◽  
First Time ◽  
532 Nm

Photopolymers can be used to fabricate different holographic optical elements, although maximization of the phase-shift in photopolymers has been a challenge for the last few decades. Different material compositions and irradiation conditions have been studied in order to achieve it. One of the main conclusions has been that with continuous laser exposure better results are achieved. However, our results show for the first time that higher phase-shift can be achieved using a pulsed laser. The study has been conducted with crosslinked acrylamide-based photopolymers exposed with a pulsed laser (532 nm). The increment of the phase-shift between the pulsed laser and continuous laser exposure is 17%, achieving a maximum phase-shift of 3π radians and a refractive index shift of 0.0084 at the zero spatial frequency limit, where monomer diffusion does not take place. This allows this photopolymer to be used in large-scale manufacturing.

Sign in / Sign up

Export Citation Format

Share Document