scholarly journals Flexible Transparent Electrode Characteristics of Graphene Oxide/Cysteamine/AgNP/AgNW Structure

Nanomaterials ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 2352
Author(s):  
Junhwan Jang ◽  
Ju-Young Choi ◽  
Jihyun Jeon ◽  
Jeongjun Lee ◽  
Jaehyuk Im ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Graphene Oxide ◽  
Optical Transmittance ◽  
Transparent Electrode ◽  
Silver Nanowire ◽  
Bending Test ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Current Voltage

Graphene oxide (GO)–cysteamine–Ag nanoparticles (GCA)–silver nanowire (AgNW) fabricated by depositing GCA over sprayed AgNWs on PET films were proposed for transparent and flexible electrodes, and their optical, electrical, and mechanical properties were analyzed by energy-dispersive X-ray spectroscopy, Fourier-transform infrared spectroscopy, Raman spectroscopy, atomic force microscopy, scanning electron microscopy, transmission electron microscopy, current-voltage measurements, and bending test. GCA–AgNW electrodes show optical transmittance of >80% at 550 nm and exhibit a high figure-of-merit value of up to 116.13 in the samples with sheet resistances of 20–40 Ω/◻. It was observed that the detrimental oxidation of bare AgNWs over time was considerably decreased, and the mechanical robustness was improved. To apply the layer as an actual electrode in working devices, a Pt/GO/poly(3,4-ethylenedioxythiophene) polystyrene sulfonate/GCA–AgNW/polyethylene terephthalate structure was fabricated, and resistive switching memory was demonstrated. On the basis of these results, we confirm that the proposed GCA–AgNW layer can be used as transparent and flexible electrode.

scholarly journals Enhancement of barrier and anti-corrosive performance of zinc-rich epoxy coatings using nano-silica/graphene oxide hybrid

2020 ◽  
Vol 38 (6) ◽  
pp. 497-513
Author(s):  
Meiling Zhang ◽  
Hui Wang ◽  
Ting Nie ◽  
Jintao Bai ◽  
Fei Zhao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Graphene Oxide ◽  
Corrosion Protection ◽  
Electrochemical Impedance ◽  
Epoxy Coating ◽  
X Ray Diffraction ◽  
Protection Efficiency ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron

AbstractThis study reports a facile method to prepare silica-coated graphene oxide nanoflakes (SiO2–GO). Results of X-ray diffraction analysis, Raman spectroscopy, Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy and atomic force microscopy reveal that silica was successfully coated on the GO flakes. The effect of SiO2–GO nanosheets on the corrosion protection and barrier performance of the epoxy coating was investigated in this work. Results indicate that the mechanical properties of all coatings added with GO and SiO2–GO were significantly improved. Furthermore, electrochemical impedance and Tafer polarisation curves showed that added 0.5 wt% SiO2–GO nanoflakes into zinc-rich epoxy coating could greatly improve the anti-corrosion performance of the sample, and the corrosion protection efficiency increased from 67.01 to 99.58%.

scholarly journals Synthesis and characterization of graphene oxide/ gold nanoparticles/ dibenzothiophene heterogeneous nanostructures

2020 ◽  
Vol 65 (9) ◽  
pp. 777-782
Author(s):  
Fatma Bayrakçeken NİŞANCI ◽  
Keyword(s):  
Electron Microscopy ◽  
Graphene Oxide ◽  
Photocatalytic Oxidation ◽  
Synthesis And Characterization ◽  
Au Nps ◽  
Adsorption Time ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron

This work examines the effect of gold nanoparticle (Au NP)- graphene oxide (GO) on the adsorption of dibenzothiophene (DBT) compounds. Au NP-GO were also used as an absorbent to produce nanoscale samples of DBT selfassembled monolayers (SAMs) on Au NP-GO. The influences of DBT adsorption on the size and the time of patterns were investigated. Atomic force microscopy (AFM) and Transmission electron microscopy (TEM) measurements showed that all of the uniformly distributed on Au NP- GO preliminary results indicated that the diameter and the density of DBT adsorptive can be controlled by controlling concentration of GO and Au NP and adsorption time during DBT the stage of SAMs. Photocatalytic oxidation of DBT was studied over Au NPs incorporated DBT Au NP-GO- DBT catalyst under UV radiation.

Defect-Engineered Graded GexSi1-x Buffers on Si (001) with Extreme Low Threading Dislocation Density

1995 ◽  
Vol 378 ◽  
Author(s):  
G. Kissinger ◽  
T. Morgenstern ◽  
G. Morgenstern ◽  
H. B. Erzgräber ◽  
H. Richter
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Atomic Force Microscopy ◽  
Dislocation Density ◽  
Threading Dislocation ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Dislocation Densities ◽  
Threading Dislocation Density

AbstractStepwise equilibrated graded GexSii-x (x≤0.2) buffers with threading dislocation densities between 102 and 103 cm−2 on the whole area of 4 inch silicon wafers were grown and studied by transmission electron microscopy, defect etching, atomic force microscopy and photoluminescence spectroscopy.

Effectiveness and Reliability of Metal Diffusion Barriers for Copper Interconnects

1995 ◽  
Vol 403 ◽  
Author(s):  
G. Bai ◽  
S. Wittenbrock ◽  
V. Ochoa ◽  
R. Villasol ◽  
C. Chiang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Vapor Deposition ◽  
Physical Vapor Deposition ◽  
Chemical Vapor ◽  
Diffusion Barriers ◽  
Copper Interconnects ◽  
Time To Failure ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron

AbstractCu has two advantages over Al for sub-quarter micron interconnect application: (1) higher conductivity and (2) improved electromigration reliability. However, Cu diffuses quickly in SiO2and Si, and must be encapsulated. Polycrystalline films of Physical Vapor Deposition (PVD) Ta, W, Mo, TiN, and Metal-Organo Chemical Vapor Deposition (MOCVD) TiN and Ti-Si-N have been evaluated as Cu diffusion barriers using electrically biased-thermal-stressing tests. Barrier effectiveness of these thin films were correlated with their physical properties from Atomic Force Microscopy (AFM), Transmission Electron Microscopy (TEM), Secondary Electron Microscopy (SEM), and Auger Electron Spectroscopy (AES) analysis. The barrier failure is dominated by “micro-defects” in the barrier film that serve as easy pathways for Cu diffusion. An ideal barrier system should be free of such micro-defects (e.g., amorphous Ti-Si-N and annealed Ta). The median-time-to-failure (MTTF) of a Ta barrier (30 nm) has been measured at different bias electrical fields and stressing temperatures, and the extrapolated MTTF of such a barrier is > 100 year at an operating condition of 200C and 0.1 MV/cm.

Development of Ge Nanoparticles Embedded in GeO2 Matrix

2008 ◽  
Vol 8 (8) ◽  
pp. 4081-4085 ◽  
Author(s):  
Y. Batra ◽  
D. Kabiraj ◽  
D. Kanjilal
Keyword(s):  
Electron Microscopy ◽  
Annealing Temperature ◽  
Spectroscopic Studies ◽  
Electron Beam Evaporation ◽  
Granular Structure ◽  
Raman Analysis ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Ge Nanocrystals

Germanium (Ge) nanoparticles have attracted a lot of attention due to their excellent optical properties. In this paper, we report on the formation of Ge nanoparticles embedded in GeO2 matrix prepared by electron beam evaporation and subsequent annealing. Transmission electron microscopy (TEM) studies clearly indicate the formation of Ge nanocrystals in the films annealed at 500 °C. Fourier transform infrared (FTIR) spectroscopic studies are carried out to verify the evolution of the structure after annealingat each stage. Micro-Raman analysis also confirms the formation of Ge nanoparticles in the annealed films. Development of Ge nanoparticles is also established by photoluminescence (PL) analysis. Surface morphology study is carried out by atomic force microscopy (AFM). It shows the evolution of granular structure of the films with increasing annealing temperature.

scholarly journals Measuring the Autocorrelation Function of Nanoscale Three-Dimensional Density Distribution in Individual Cells Using Scanning Transmission Electron Microscopy, Atomic Force Microscopy, and a New Deconvolution Algorithm

2017 ◽  
Vol 23 (3) ◽  
pp. 661-667 ◽  
Author(s):  
Yue Li ◽  
Di Zhang ◽  
Ilker Capoglu ◽  
Karl A. Hujsak ◽  
Dhwanil Damania ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Density Distribution ◽  
Scanning Transmission Electron Microscopy ◽  
Mass Density ◽  
Three Dimensional ◽  
Force Microscopy ◽  
Statistical Measures ◽  
Atomic Force ◽  
Transmission Electron ◽  
Scanning Transmission

AbstractEssentially all biological processes are highly dependent on the nanoscale architecture of the cellular components where these processes take place. Statistical measures, such as the autocorrelation function (ACF) of the three-dimensional (3D) mass–density distribution, are widely used to characterize cellular nanostructure. However, conventional methods of reconstruction of the deterministic 3D mass–density distribution, from which these statistical measures can be calculated, have been inadequate for thick biological structures, such as whole cells, due to the conflict between the need for nanoscale resolution and its inverse relationship with thickness after conventional tomographic reconstruction. To tackle the problem, we have developed a robust method to calculate the ACF of the 3D mass–density distribution without tomography. Assuming the biological mass distribution is isotropic, our method allows for accurate statistical characterization of the 3D mass–density distribution by ACF with two data sets: a single projection image by scanning transmission electron microscopy and a thickness map by atomic force microscopy. Here we present validation of the ACF reconstruction algorithm, as well as its application to calculate the statistics of the 3D distribution of mass–density in a region containing the nucleus of an entire mammalian cell. This method may provide important insights into architectural changes that accompany cellular processes.

scholarly journals Spore Coat Architecture of Clostridium novyi NT Spores

2007 ◽  
Vol 189 (17) ◽  
pp. 6457-6468 ◽  
Author(s):  
Marco Plomp ◽  
J. Michael McCaffery ◽  
Ian Cheong ◽  
Xin Huang ◽  
Chetan Bettegowda ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Anaerobic Bacterium ◽  
Amorphous Layer ◽  
Spore Coat ◽  
Experimental Animals ◽  
Force Microscopy ◽  
Atomic Force ◽  
Clostridium Novyi ◽  
Transmission Electron

ABSTRACT Spores of the anaerobic bacterium Clostridium novyi NT are able to germinate in and destroy hypoxic regions of tumors in experimental animals. Future progress in this area will benefit from a better understanding of the germination and outgrowth processes that are essential for the tumorilytic properties of these spores. Toward this end, we have used both transmission electron microscopy and atomic force microscopy to determine the structure of both dormant and germinating spores. We found that the spores are surrounded by an amorphous layer intertwined with honeycomb parasporal layers. Moreover, the spore coat layers had apparently self-assembled, and this assembly was likely to be governed by crystal growth principles. During germination and outgrowth, the honeycomb layers, as well as the underlying spore coat and undercoat layers, sequentially dissolved until the vegetative cell was released. In addition to their implications for understanding the biology of C. novyi NT, these studies document the presence of proteinaceous growth spirals in a biological organism.

Sign in / Sign up

Export Citation Format

Share Document