scholarly journals Application of Nano-Hydroxyapatite Derived from Oyster Shell in Fabricating Superhydrophobic Sponge for Efficient Oil/Water Separation

Molecules ◽  
2021 ◽  
Vol 26 (12) ◽  
pp. 3703
Author(s):  
Chao Liu ◽  
Su-Hua Chen ◽  
Chi-Hao Yang-Zhou ◽  
Qiu-Gen Zhang ◽  
Ruby N. Michael
Keyword(s):  
Oil Recovery ◽  
Superhydrophobic Surface ◽  
Oyster Shell ◽  
Contact Angles ◽  
Immersion Method ◽  
Water Separation ◽  
Promising Alternative ◽  
Recovery Capacity ◽  
Oil Water Separation ◽  
Oil Water

The exploration of nonhazardous nanoparticles to fabricate a template-driven superhydrophobic surface is of great ecological importance for oil/water separation in practice. In this work, nano-hydroxyapatite (nano-HAp) with good biocompatibility was easily developed from discarded oyster shells and well incorporated with polydimethylsiloxane (PDMS) to create a superhydrophobic surface on a polyurethane (PU) sponge using a facile solution–immersion method. The obtained nano-HAp coated PU (nano-HAp/PU) sponge exhibited both excellent oil/water selectivity with water contact angles of over 150° and higher absorption capacity for various organic solvents and oils than the original PU sponge, which can be assigned to the nano-HAp coating surface with rough microstructures. Moreover, the superhydrophobic nano-HAp/PU sponge was found to be mechanically stable with no obvious decrease of oil recovery capacity from water in 10 cycles. This work presented that the oyster shell could be a promising alternative to superhydrophobic coatings, which was not only beneficial to oil-containing wastewater treatment, but also favorable for sustainable aquaculture.

Advancement Towards the Full-Field Implementation of Marmul Alkaline-Surfactant-Polymer in the Sultanate of Oman

2021 ◽  
Author(s):  
Dawood Al Mahrouqi ◽  
Hanaa Sulaimani ◽  
Rouhi Farajzadeh ◽  
Yi Svec ◽  
Samya Farsi ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Phase 1 ◽  
Recovery Efficiency ◽  
Sultanate Of Oman ◽  
Water Separation ◽  
Full Field ◽  
Oil Water Separation ◽  
Oil Water ◽  
New Formulation ◽  
Alkaline Surfactant Polymer

Abstract In 2015-2016, the Alkaline-Surfactant-Polymer (ASP) flood Pilot in Marmul was successfully completed with ∼30% incremental oil recovery and no significant operational issues. In parallel to the ASP pilot, several laboratory studies were executed to identify an alternative and cost-efficient ASP formulation with simpler logistics. The studies resulted in a new formulation based on mono-ethanolamine (MEA) as alkali and a blend of commercially available and cheaper surfactants. To expediate the phased full field development, Phase-1 project was started in 2019 with the following main objectives are confirm high oil recovery efficiency of the new ASP formulation and ensure the scalability and further commercial maturation of ASP technology; de-risk the injectivity of new formulation; and de-risk oil-water separation in the presence of produced ASP chemicals. The Phase 1 project was executed in the same well pattern as the Pilot, but at a different reservoir unit that is more heterogeneous and has a smaller pore volume (PV) than those of the Pilot. This set-up allowed comparing the performance of ASP formulations and taking advantage of the existing surface facilities, thus reducing the project cost. The project was successfully finished in December 2020, and the following major conclusions were made: (1) with the estimated incremental recovery of around 15-18% and one of the producers exhibiting water cut reversal of more than 30%, the new ASP formulation is efficient and will be used in the follow-up phased commercial ASP projects; (2) the injectivity was sustained throughout the entire operations within the target rate and below the fracture pressure; (3) produced oil quality met the export requirements and a significant amount of oil-water separation data was collected. With confirmed high oil recovery efficiency for the cheaper and more convenient ASP formulation, the success of ASP flooding in the Phase-1 project paves the way for the subsequent commercial-scale ASP projects in the Sultanate of Oman.

scholarly journals Superhydrophobic foam prepared from high internal phase emulsion templates stabilised by oyster shell powder for oil–water separation

RSC Advances ◽  
2019 ◽  
Vol 9 (31) ◽  
pp. 17543-17550 ◽  
Author(s):  
Chuan-ming Yu ◽  
Xiao-hui Zhuang ◽  
Sheng-wei Zeng ◽  
Qi-xing Dong ◽  
Zhan-xin Jing ◽  
...  
Keyword(s):  
Oyster Shell ◽  
Water Separation ◽  
High Internal Phase Emulsion ◽  
Internal Phase ◽  
Styrene Divinylbenzene ◽  
Oil Water Separation ◽  
Oil Water ◽  
Oyster Shell Powder ◽  
Span 80 ◽  
Shell Powder

Poly(styrene-divinylbenzene) foam was synthesized through a high internal phase emulsion (HIPE) technique with Span 80 and superfine oyster shell powder as a co-emulsifier, and the foam exhibited excellent superhydrophobicity and oleophilicity.

Research of Water Quality in Typical Low Permeability Oilfield Produced Water Treatment

2014 ◽  
Vol 556-562 ◽  
pp. 867-871
Author(s):  
Qiu Shi Zhao
Keyword(s):  
Water Quality ◽  
Oil Recovery ◽  
Treatment Process ◽  
Produced Water ◽  
Sewage Treatment ◽  
Oil Fields ◽  
Water Separation ◽  
Oil Water Separation ◽  
Oilfield Produced Water ◽  
Oil Water

It is significative to study sewage treatment process in low permeable oil fields. It could enhance the oil recovery. The water quality characteristics and oil/water separation characteristics were researched during different period process by GC-MS. It shows that there are about 108 kinds of organic matters, including 45 kinds of aliphatic hydrocarbon, 7 kinds of aine, 5 kinds of sulfocompound and 9 kinds of hexacyclic compounds, such as Benzene, phenol, naphthalene and anthracene. The percent of oil droplets which size was less than 10μm is 57.3%, compared to 91.6% which size was more than 50μm. It is difficult to separate the water and oil. The remaining oil was emulsified oil. The process was hard to decrease COD, and some pollutants were existed in water, such as Arsenic, Selenium, Mercury ,Cadmium and Cr6+. It is further proposed to optimize and develop this process to removal oil and suspended solids.

High Adhesion Superhydrophobic Surface Constructed by PDMS-co-PMHS Coatings Embedded with SiO2 Particles

2021 ◽  
Vol 8 (3) ◽  
pp. 23-32
Author(s):  
Wei Zhang ◽  
Shang Hao ◽  
Mingyang Chen ◽  
Bo Yang ◽  
Yuan Xie ◽  
...  
Keyword(s):  
Superhydrophobic Surface ◽  
Flexible Substrate ◽  
Nonwoven Fabric ◽  
Water Impact ◽  
Water Contact ◽  
Water Separation ◽  
Superhydrophobic Coatings ◽  
High Adhesion ◽  
Oil Water Separation ◽  
Oil Water

Superhydrophobic surfaces have attracted attention due to their hydrophobic, self-cleaning, anti-icing, and oil/water separation properties. The present study used a nonwoven fabric as a flexible substrate and constructed a high-adhesive superhydrophobic surface by coating the fabric with polydimethylsiloxane (PDMS)-co -polymethyl hydrogen siloxane (PMHS) polymers and embedding mesoporous SiO2 nanoparticles. The water contact angle (WCA) of the superhydrophobic surface was up to 165.2° at a PDMS to PMHS ratio of 4:1. The adhesion to deionized water was 99.7 μN. High hydrophobicity was maintained, even after sandpaper abrasions and flowing water impact. The surface was resistant to acid, alkali, brine, strong oxidation, and heavy metal solutions. The coating exhibited anti-icing and oil/water separation properties. This study provides a facile and effective method for constructing multifunctional superhydrophobic coatings on flexible substrates.

scholarly journals Preparation of Parabolic Superhydrophobic Material for Oil-Water Separation

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 1914 ◽  
Author(s):  
Xiaoying Qiao ◽  
Chunyan Yang ◽  
Qian Zhang ◽  
Shengke Yang ◽  
Yangyang Chen ◽  
...  
Keyword(s):  
Contact Angle ◽  
Carbon Tetrachloride ◽  
Separation Efficiency ◽  
Contact Angles ◽  
Engine Oil ◽  
Water Droplets ◽  
Water Separation ◽  
Oil Water Separation ◽  
Oil Water ◽  
Copper Mesh

In order to prepare parabolic superhydrophobic materials, copper meshes were used as the substrate and ultrasonic etching and oxidative corrosion were carried out with FeCl3 solution and H2O2 solution, respectively, and then the surface was modified with stearic acid (SA). The topological structure and surface wettability of the prepared mesh were characterized by fluorescence microscope, scanning electron microscopy and contact angle measurement. Finally, the as-prepared copper meshes were applied to oil-water separation. The results showed that the micro-nano-mastoid structure on the surface of the copper mesh was flaky bulges, forming a rough structure similar to a paraboloid. When the oxidative corrosion time of H2O2 was 1 min, it is more beneficial to increase the hydrophobicity of the surface of the copper mesh and increase the contact angle of water droplets on the surface of the membrane. Additionally, based on superhydrophobic materials of the parabolic copper mesh, the static contact angles of the water droplets, engine oil and carbon tetrachloride with the surface were approximately 153.6°, 5° and 0.1°, respectively and the sliding angle of the water droplets with the surface were approximately 4.9°. The parabolic membrane was applied to discuss the separation efficiency of different oils with deionized water and the separation efficiency was obtained as benzene > carbon tetrachloride > oil > machine oil. Therefore, based on the research, the parabolic superhydrophobic material has good efficiency of oil-water separation.

Sign in / Sign up

Export Citation Format

Share Document