scholarly journals Study on the Adsorption of CuFe2O4-Loaded Corncob Biochar for Pb(II)

Molecules ◽  
2020 ◽  
Vol 25 (15) ◽  
pp. 3456
Author(s):  
Tianci Zhao ◽  
Xiaolong Ma ◽  
Hao Cai ◽  
Zichuan Ma ◽  
Huifeng Liang
Keyword(s):  
Adsorption Capacity ◽  
Maximum Adsorption Capacity ◽  
Face Centered Cubic ◽  
Removal Mechanism ◽  
Process Rate ◽  
Excellent Performance ◽  
Surface Complexes ◽  
Adsorption Dynamics ◽  
Inner Surface ◽  
Face Centered

A series of the magnetic CuFe2O4-loaded corncob biochar (CuFe2O4@CCBC) materials was obtained by combining the two-step impregnation of the corncob biochar with the pyrolysis of oxalate. CuFe2O4@CCBC and the pristine corncob biochar (CCBC) were characterized using XRD, SEM, VSM, BET, as well as pHZPC measurements. The results revealed that CuFe2O4 had a face-centered cubic crystalline phase and was homogeneously coated on the surface of CCBC. The as-prepared CuFe2O4@CCBC(5%) demonstrated a specific surface area of 74.98 m2·g−1, saturation magnetization of 5.75 emu·g−1 and pHZPC of 7.0. The adsorption dynamics and thermodynamic behavior of Pb(II) on CuFe2O4@CCBC and CCBC were investigated. The findings indicated that the pseudo-second kinetic and Langmuir equations suitably fitted the Pb(II) adsorption by CuFe2O4@CCBC or CCBC. At 30 °C and pH = 5.0, CuFe2O4@CCBC(5%) displayed an excellent performance in terms of the process rate and adsorption capacity towards Pb(II), for which the theoretical rate constant (k2) and maximum adsorption capacity (qm) were 7.68 × 10−3 g·mg−1··min−1 and 132.10 mg·g−1 separately, which were obviously higher than those of CCBC (4.38 × 10−3 g·mg−1·min−1 and 15.66 mg·g−1). The thermodynamic analyses exhibited that the adsorption reaction of the materials was endothermic and entropy-driven. The XPS and FTIR results revealed that the removal mechanism could be mainly attributed to the replacement of Pb2+ for H+ in Fe/Cu–OH and –COOH to form the inner surface complexes. Overall, the magnetic CuFe2O4-loaded biochar presents a high potential for use as an eco-friendly adsorbent to eliminate the heavy metals from the wastewater streams.

scholarly journals Sorption and mechanism studies of Cu2+, Sr2+ and Pb2+ ions on mesoporous aluminosilicates/zeolite composite sorbents

2020 ◽  
Vol 82 (5) ◽  
pp. 984-997
Author(s):  
Tatyana Kouznetsova ◽  
Andrei Ivanets ◽  
Vladimir Prozorovich ◽  
Ahmad Hosseini-Bandegharaei ◽  
Hai Nguyen Tran ◽  
...  
Keyword(s):  
Ion Exchange ◽  
Metal Ions ◽  
Adsorption Capacity ◽  
Surface Complexation ◽  
Bet Surface Area ◽  
Precipitation Method ◽  
Maximum Adsorption Capacity ◽  
Zeolite Nay ◽  
Inner Surface ◽  
Zeolite Composite

Abstract The research aimed to develop a novel mesoporous aluminosilicate/zeolite composite by the template co-precipitation method. The effect of aluminosilicate (AlSi) and zeolite (NaY) on the basic properties and adsorption capacity of the resultant composite was conducted at different mass ratios of AlSi/NaY (i.e., 5/90, 10/80, 15/85, 20/80, and 50/50). The adsorption characteristics of such composite and its feedstock materials (i.e., aluminosilicates and zeolite) towards radioactive Sr2+ ions and toxic metals (Cu2+ and Pb2+ ions) in aqueous solutions were investigated. Results indicated that BET surface area (SBET), total pore volume (VTotal), and mesopore volume (VMeso) of prepared materials followed the decreasing order: aluminosilicate (890 m2/g, 0.680 cm3/g, and 0.644 cm3/g) > zeolite (623 m2/g, 0.352 cm3/g, and 0.111 cm3/g) > AlSi/NaY (20/80) composite (370 m2/g, 0.254 cm3/g, and 0.154 cm3/g, respectively). The Langmuir maximum adsorption capacity (Qm) of metal ions (Sr2+, Cu2+, and Pb2+) in single-component solution was 260 mg/g, 220 mg/g, and 161 mg/g (for zeolite), 153 mg/g, 37.9 mg/g, and 66.5 mg/g (for aluminosilicate), and 186 mg/g, 140 mg/g, and 77.8 mg/g for (AlSi/NaY (20/80) composite), respectively. Ion exchange was regarded as a domain adsorption mechanism of metal ions in solution by zeolite; meanwhile, inner-surface complexation was domain one for aluminosilicate. Ion exchange and inner-surface complexation might be mainly responsible for adsorbing metal ions onto the AlSi/NaY composite. Pore-filling mechanism was a less important contributor during the adsorption process. The results of competitive adsorption under binary-components (Cu2+ and Sr2+) and ternary-components (Cu2+, Pb2+, and Sr2) demonstrated that the removal efficacy of target metals by the aluminosilicate, zeolite, and their composite remarkably decreased. The synthesized AlSi/NaY composite might serve as a promising adsorbent for real water treatment.

Synthesis of the Water-Compatible P-Aminophenol Resin and its Adsorption for Salicylic Acid

2011 ◽  
Vol 311-313 ◽  
pp. 1852-1856 ◽  
Author(s):  
Gu Qing Xiao ◽  
Xue Jun Zhang
Keyword(s):  
Salicylic Acid ◽  
Adsorption Capacity ◽  
Equilibrium Concentration ◽  
Maximum Adsorption Capacity ◽  
Adsorption Dynamics ◽  
First Order ◽  
Rate Limiting Step ◽  
Intra Particle Diffusion ◽  
Rate Limiting ◽  
Order Rate Equation

A novel water-compatible hypercrosslinked resin modified by p-aminophenol was synthesized with chloromethylated polystyrene and p-aminophenol by Friedel-Crafts reaction. The objective of this work was to study the adsorption performances for salicylic acid onto p-aminophenol resin. The results showed that the adsorption capacity of salicylic acid onto p-aminophenol resin was superior to XAD-4 resin. It is seen that the maximum adsorption capacity is observed at pH of 3.0. It was found the adsorption dynamics obeyed the pseudo-first-order rate equation and the intra-particle diffusion was the rate-limiting step. The maximum adsorption capacity of salicylic acid for p-aminophenol resin was measured to be 283.7 mg/g with the equilibrium concentration at 404.6mg/L. The micropore structure, the pore diameter of p-aminophenol resin, the hydrogen bond between p-aminophenol resin and salicylic acid bring the larger adsorption capacity.

Voids in Irradiated Tungsten and Molybdenum

1969 ◽  
Vol 27 ◽  
pp. 190-191
Author(s):  
Robert C. Rau ◽  
Robert L. Ladd
Keyword(s):  
Melting Point ◽  
Fast Neutron ◽  
Neutron Irradiation ◽  
Elevated Temperatures ◽  
Irradiation Temperature ◽  
The Body ◽  
Face Centered Cubic ◽  
Body Centered Cubic ◽  
Cubic Metals ◽  
Face Centered

Recent studies have shown the presence of voids in several face-centered cubic metals after neutron irradiation at elevated temperatures. These voids were found when the irradiation temperature was above 0.3 Tm where Tm is the absolute melting point, and were ascribed to the agglomeration of lattice vacancies resulting from fast neutron generated displacement cascades. The present paper reports the existence of similar voids in the body-centered cubic metals tungsten and molybdenum.

A study of interface sliding at F.C.C.-B.C.C. boundaries in a Cu-Zn alloy

1978 ◽  
Vol 36 (1) ◽  
pp. 422-423
Author(s):  
F. Monchoux ◽  
A. Rocher ◽  
J.L. Martin
Keyword(s):  
Face Centered Cubic ◽  
Creep Tests ◽  
High Voltage Electron Microscopy ◽  
Diffusion Treatment ◽  
Voltage Electron ◽  
The Face ◽  
Face Centered ◽  
Interface Sliding ◽  
Zn Alloy ◽  
Made In

Interphase sliding is an important phenomenon of high temperature plasticity. In order to study the microstructural changes associated with it, as well as its influence on the strain rate dependence on stress and temperature, plane boundaries were obtained by welding together two polycrystals of Cu-Zn alloys having the face centered cubic and body centered cubic structures respectively following the procedure described in (1). These specimens were then deformed in shear along the interface on a creep machine (2) at the same temperature as that of the diffusion treatment so as to avoid any precipitation. The present paper reports observations by conventional and high voltage electron microscopy of the microstructure of both phases, in the vicinity of the phase boundary, after different creep tests corresponding to various deformation conditions.Foils were cut by spark machining out of the bulk samples, 0.2 mm thick. They were then electropolished down to 0.1 mm, after which a hole with thin edges was made in an area including the boundary

Microstructure of Electro-Eroded Cemented Carbide Surfaces

1968 ◽  
Vol 26 ◽  
pp. 284-285
Author(s):  
V. N. Filimonenko ◽  
M. H. Richman ◽  
J. Gurland
Keyword(s):  
Surface Layer ◽  
Cobalt Content ◽  
Cemented Carbides ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
Metallographic Examination ◽  
Standard Procedures ◽  
Face Centered ◽  
Diamond Paste ◽  
Plastic Carbon

The high temperatures and pressures that are found in a spark gap during electrical discharging lead to a sharp phase transition and structural transformation in the surface layer of cemented carbides containing WC and cobalt. By means of X-ray diffraction both W2C and a high-temperature monocarbide of tungsten (face-centered cubic) were detected after electro-erosion. The W2C forms as a result of the peritectic reaction, WC → W2C+C. The existence and amount of the phases depend on both the energy of the electro-spark discharge and the cobalt content. In the case of a low-energy discharge (i.e. C=0.01μF, V = 300v), WC(f.c.c.) is generally formed in the surface layer. However, at high energies, (e.g. C=30μF, V = 300v), W2C is formed at the surface in preference to the monocarbide. The phase transformations in the surface layer are retarded by the presence of larger percentages of cobalt.Metallographic examination of the electro-eroded surfaces of cemented carbides was carried out on samples with 5-30% cobalt content. The specimens were first metallographically polished using diamond paste and standard procedures and then subjected to various electrical discharges on a Servomet spark machining device. The samples were then repolished and etched in a 3% NH4OH electrolyte at -0.5 amp/cm2. Two stage plastic-carbon replicas were then made and shadowed with chromium at 27°.

Faceted antiphase boundaries in GaAs grown on Ge

1987 ◽  
Vol 45 ◽  
pp. 314-315
Author(s):  
N.-H. Cho ◽  
S. McKernan ◽  
C.B. Carter ◽  
K. Wagner
Keyword(s):  
Cross Section ◽  
Atomic Resolution ◽  
Face Centered Cubic ◽  
Electrical Behavior ◽  
Sphalerite Structure ◽  
Antiphase Boundaries ◽  
Transmission Electron ◽  
Face Centered ◽  
Quality Material ◽  
Simulated Images

Interest has recently increased in the possibility of growing III-V compounds epitactically on non-polar substrates to produce device quality material. Antiphase boundaries (APBs) may then develop in the GaAs epilayer because it has sphalerite structure (face-centered cubic with a two-atom basis). This planar defect may then influence the electrical behavior of the GaAs epilayer. The orientation of APBs and their propagation into GaAs epilayers have been investigated experimentally using both flat-on and cross-section transmission electron microscope techniques. APBs parallel to (110) plane have been viewed at the atomic resolution and compared to simulated images.Antiphase boundaries were observed in GaAs epilayers grown on (001) Ge substrates. In the image shown in Fig.1, which was obtained from a flat-on sample, the (110) APB planes can be seen end-on; the faceted APB is visible because of the stacking fault-like fringes arising from a lattice translation at this interface.

Electron diffraction detection of ordliking in annealed PbTe thin film

1990 ◽  
Vol 48 (4) ◽  
pp. 1018-1019
Author(s):  
Karimat El-Sayed
Keyword(s):  
Thin Film ◽  
Electron Diffraction ◽  
Lead Telluride ◽  
Structural Basis ◽  
Face Centered Cubic ◽  
X Ray ◽  
Polycrystalline Thin Films ◽  
Stage Process ◽  
Diffraction Patterns ◽  
Face Centered

Lead telluride is an important semiconductor of many applications. Many Investigators showed that there are anamolous descripancies in most of the electrophysical properties of PbTe polycrystalline thin films on annealing. X-Ray and electron diffraction studies are being undertaken in the present work in order to explain the cause of this anamolous behaviour.Figures 1-3 show the electron diffraction of the unheated, heated in air at 100°C and heated in air at 250°C respectively of a 300°A polycrystalline PbTe thin film. It can be seen that Fig. 1 is a typical [100] projection of a face centered cubic with unmixed (hkl) indices. Fig. 2 shows the appearance of faint superlattice reflections having mixed (hkl) indices. Fig. 3 shows the disappearance of thf superlattice reflections and the appearance of polycrystalline PbO phase superimposed on the [l00] PbTe diffraction patterns. The mechanism of this three stage process can be explained on structural basis as follows :

NICROFER 5923 HMo-ALLOY 59

Alloy Digest ◽  
1993 ◽  
Vol 42 (5) ◽  
Keyword(s):  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Heat Treating ◽  
Face Centered Cubic ◽  
Low Carbon ◽  
High Alloy ◽  
Temperature Performance ◽  
Cubic Structure ◽  
Face Centered

Abstract NICROFER 5923 hMo, often called Alloy 59, was developed with extra low carbon and silicon contents and with a high alloy level of molybdenum to optimize its corrosion resistance. Nicrofer 5923hMo has a face-centered cubic structure. This datasheet provides information on composition, physical properties, elasticity, and tensile properties. It also includes information on high temperature performance as well as forming, heat treating, and joining. Filing Code: Ni-430. Producer or source: VDM Technologies Corporation.

Utilization of Waste of Enzymes Biomass as Biosorbent for the Removal of Dyes from Aqueous Solution in Batch and Fluidized Bed Column

2020 ◽  
Vol 71 (1) ◽  
pp. 1-12
Author(s):  
Salman H. Abbas ◽  
Younis M. Younis ◽  
Mohammed K. Hussain ◽  
Firas Hashim Kamar ◽  
Gheorghe Nechifor ◽  
...  
Keyword(s):  
Experimental Data ◽  
Aqueous Solution ◽  
Particle Size ◽  
Adsorption Capacity ◽  
Fluidized Bed ◽  
Flow Rate ◽  
Fungal Biomass ◽  
Solution Flow Rate ◽  
Maximum Adsorption Capacity ◽  
Solution Flow

The biosorption performance of both batch and liquid-solid fluidized bed operations of dead fungal biomass type (Agaricusbisporus ) for removal of methylene blue from aqueous solution was investigated. In batch system, the adsorption capacity and removal efficiency of dead fungal biomass were evaluated. In fluidized bed system, the experiments were conducted to study the effects of important parameters such as particle size (701-1400�m), initial dye concentration(10-100 mg/L), bed depth (5-15 cm) and solution flow rate (5-20 ml/min) on breakthrough curves. In batch method, the experimental data was modeled using several models (Langmuir,Freundlich, Temkin and Dubinin-Radushkviechmodels) to study equilibrium isotherms, the experimental data followed Langmuir model and the results showed that the maximum adsorption capacity obtained was (28.90, 24.15, 21.23 mg/g) at mean particle size (0.786, 0.935, 1.280 mm) respectively. In Fluidized-bed method, the results show that the total ion uptake and the overall capacity will be decreased with increasing flow rate and increased with increasing initial concentrations, bed depth and decreasing particle size.

Sign in / Sign up

Export Citation Format

Share Document