Summary
Well deliverability in many gas-condensate reservoirs is reduced by condensate banking when the bottomhole pressure falls below the dewpoint, although the impact of condensate banking may be reduced due to improved mobility at high capillary number in the near-well region.
This paper presents the results of relative permeability measurements on a sandstone core from a North Sea gas-condensate reservoir, at velocities that are typical of the near-well region. The results show a clear increase in mobility with capillary number, and the paper describes how the data can be modeled with empirical correlations which can be used in reservoir simulators.
Introduction
Well deliverability is an important issue in the development of many gas-condensate reservoirs, especially where permeability is low. When the well bottomhole flowing pressure falls below the dewpoint, condensate liquid may build up around the wellbore, causing a reduction in gas permeability and well productivity. In extreme cases the liquid saturation may reach values as high as 50 or 60% and the well deliverability may be reduced by up to an order of magnitude.
The loss in productivity due to this "condensate banking" effect may be significant, even in very lean gas-condensate reservoirs. For example, in the Arun reservoir,1 the productivity reduced by a factor of about 2 as the pressure fell below the dewpoint, even though the reservoir fluid was very lean with a maximum liquid drop out of only 1% away from the well.
Most of the pressure drop from condensate blockage occurs within a few feet of the wellbore, where velocities are very high. There is a growing body of evidence from laboratory coreflood experiments to suggest that gas-condensate relative permeabilities increase at high velocities, and that these changes can be correlated against the capillary number.2–8 The capillary number is a dimensionless number that measures the relative strength of viscous and capillary forces.
There are several gas-condensate fields where simulation with conventional relative permeability models has been found to underestimate well productivity.1,9,10 To obtain a good match between simulation results and well-test data, it was necessary to increase the mobility in the near-well region, either empirically or through a model of the increase in relative permeability at high velocity. This effect can increase well productivity significantly, and in some cases may eliminate most of the effect of condensate blockage.
Experimental Data Requirements
Fevang and Whitson11 have shown that the key parameter in determining well deliverability is the relationship between krg and the ratio krg/ kro. When high-velocity effects are significant, the most important information is the variation of krg with krg/k ro and the capillary number Nc. The relevant values of krg/kro are determined by the pressure/volume/temperature (PVT) properties of the reservoir fluids, but typical values might be 10 to 100 for lean condensates, 1 to 10 for rich condensates, and 0.1 to 10 for near-critical fluids.
There are various ways of defining the capillary number, but in this paper we use the definition (1)Nc=vgμgσ, so that the capillary number is proportional to the gas velocity and inversely proportional to interfacial tension (IFT).
The capillary numbers that are relevant for well deliverability depend on the flow rate, fluid type, and well bottomhole pressure, but as a general rule, values between 10?6 and 10?3 are most important.
Experimental Methods
In a gas-condensate reservoir, there are important differences between the flow regimes in the regions close to and far from the well. These different flow regimes are reflected in the requirements for relative permeability data for the deep reservoir and near-well regions. Far from the well, velocities are low, and liquid mobility is usually less important, except in reservoirs containing very rich fluids. In the near-well region, both liquid and gas phases are mobile, velocities are high, and the liquid mobility is important because of its effect on the relationship between krg and krg/kro.
Depletion Method.
Relative permeabilities for the deep reservoir region are often measured in a coreflood experiment, where the fluids in the core are obtained by a constant volume depletion (CVD) on a reservoir fluid sample. Relative permeabilities are measured at decreasing pressures from the fluid dewpoint, and increasing liquid saturation. In this type of experiment, the liquid saturation cannot exceed the critical condensate saturation or the maximum value in a CVD experiment, so that it is not possible to acquire data at the high liquid saturations that occur in the reservoir near to the well.
The "depletion" experiment provides relative permeability data that are relevant to the deep reservoir, but there can be problems in interpreting the results due to the effects of IFT. Changes in liquid saturation are achieved by reducing pressure, which results in a change of IFT. The increase in IFT as pressure falls may cause a large reduction in mobility, and Chen et al.12 describe an example where the condensate liquid relative permeability decreases with increasing liquid saturation.
Steady-State Method.
The steady-state technique can be used to measure relative permeabilities at the higher liquid saturations that occur in the near-well region. Liquid and gas can be injected into the core from separate vessels, allowing relative permeabilities to be measured for a wide range of saturations. Results of gas-condensate relative permeabilities measured by this technique have been reported by Henderson et al.2,6 and Chen et al.12 .
Novel Treatment for Mitigating Condensate Bank Using a Newly Synthesized Gemini Surfactant