scholarly journals Hybrid Ionic Silver and Magnetite Microgels Nanocomposites for Efficient Removal of Methylene Blue

Molecules ◽  
2019 ◽  
Vol 24 (21) ◽  
pp. 3867 ◽  
Author(s):  
Atta ◽  
Gafer ◽  
Al-Lohedan ◽  
Abdullah ◽  
Tawfeek ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Supported Catalyst ◽  
Analytical Techniques ◽  
High Rate ◽  
Heterogeneous Fenton Oxidation ◽  
Short Time ◽  
Methylene Blue Cationic Dye ◽  
Thermal Stability Of

The ionic crosslinked 2-acrylamido-2-methylpropane sulfonic acid-co-acrylic acid hydrogel, AMPS/AA and its Ag and Fe3O4 composites were synthesized using an in situ technique. The surface charge, particle sizes, morphology, and thermal stability of the prepared AMPS/AA-Ag and AMPS/AA-Fe3O4 composites were evaluated using different analytical techniques and their adsorption characteristics were evaluated to remove the methylene blue cationic dye, MB, from their aqueous solutions at optimum conditions. Also, the same monomers were used to synthesize AMPS/AA microgel and its Ag and Fe3O4 nanocomposites, which were synthesized using the same technique. The AMPS/AA-Fe3O4 nanocomposite was selected as conventional iron-supported catalyst due to the presence of both Fe(II) and Fe(III) species besides its magnetic properties that allow their easy, fast, and inexpensive separation from the aqueous solution. It was then evaluated as a heterogeneous catalyst for complete MB degradation from aqueous solution by heterogeneous Fenton oxidation. It achieved a high rate of degradation, degrading 100 mg L−1 of MB during a short time of 35 min as compared with the reported literature.

scholarly journals Synthesis of Polyaniline coated Graphene Oxide @ SrTiO3 Nanocube Nanocomposites for Enhanced Removal of Carcinogenic Dyes from Aqueous Solution

2016 ◽  
Author(s):  
Syed Shahabuddin ◽  
Norazilawati Muhamad Sarih ◽  
Muhammad Afzal Kamboh ◽  
Hamid Rashidi Nodeh ◽  
Sharifah Mohamad
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Methylene Blue ◽  
Graphene Oxide ◽  
Methyl Orange ◽  
Oxidative Polymerization ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Polymerization Method

The present investigation highlights the synthesis of polyaniline (PANI) coated graphene oxide doped with SrTiO3 nanocube nanocomposites through facile in-situ oxidative polymerization method for the efficient removal of carcinogenic dyes, namely, the cationic dye methylene blue (MB) and the anionic dye methyl orange (MO). The synthesised nanocomposites were characterised by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The adsorption efficiencies of graphene oxide (GO), PANI homopolymer and SrTiO3 nanocubes-doped nanocomposites were assessed by monitoring the adsorption of methylene blue and methyl orange dyes from aqueous solution. The adsorption efficiency of nanocomposites doped with SrTiO3 nanocubes were found to be of higher magnitude as compared with undoped nanocomposite. Moreover, the nanocomposite with 2 wt% SrTiO3 with respect to graphene oxide demonstrated excellent adsorption behaviour with 99% and 91% removal of MB and MO respectively, in a very short duration of time.

Investigation of Photocatalytic Activity of TiO2-PANi Nanocomposites

2014 ◽  
Vol 699 ◽  
pp. 53-58
Author(s):  
Zatil Amali Che Ramli ◽  
Wan Nor Roslam Wan Isahak ◽  
Mohd Ambar Yarmo ◽  
Nilofar Asim
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Uv Irradiation ◽  
Photo Degradation ◽  
Photocatalytic Activities ◽  
Pani Matrix

In this paper the photocatalytic activity of TiO2-PANi nanocomposites prepared using two differentIn-situpolymerization methods have been investigated. The same pressure, temperature, precursors, mole ratio, and solvent have been employed for preparation of nanocomposites. The synthesized nanocomposites were characterized by FESEM, XRD and FTIR. Results revealed the successful preparation of TiO2- PANI nanocomposites. TiO2-PANi nanocomposite synthesized using method 2 showed very well dispersed TiO2nanoparticles on the surface of PANi. There is no agglomeration of TiO2nanoparticles in PANi matrix. The photocatalytic activities of nanocomposites were evaluated by using photo degradation of Methylene Blue (MB) in aqueous solution under UV irradiation. These nanocomposites exhibit much higher photocatalytic activity compared with TiO2.

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

Structure of Palladium Single-Crystal Films Prepared by Flash Evaporation onto (001) NaCl Substrates

1970 ◽  
Vol 28 ◽  
pp. 456-457
Author(s):  
L. E. Murr ◽  
G. Wong
Keyword(s):  
Single Crystal ◽  
High Vacuum ◽  
Ultra High Vacuum ◽  
High Rate ◽  
Flash Evaporation ◽  
Optimum Load ◽  
Single Crystal Films ◽  
Crystal Films ◽  
A Current

Palladium single-crystal films have been prepared by Matthews in ultra-high vacuum by evaporation onto (001) NaCl substrates cleaved in-situ, and maintained at ∼ 350° C. Murr has also produced large-grained and single-crystal Pd films by high-rate evaporation onto (001) NaCl air-cleaved substrates at 350°C. In the present work, very large (∼ 3cm2), continuous single-crystal films of Pd have been prepared by flash evaporation onto air-cleaved (001) NaCl substrates at temperatures at or below 250°C. Evaporation rates estimated to be ≧ 2000 Å/sec, were obtained by effectively short-circuiting 1 mil tungsten evaporation boats in a self-regulating system which maintained an optimum load current of approximately 90 amperes; corresponding to a current density through the boat of ∼ 4 × 104 amperes/cm2.

A very rapid in situ Kikuchi technique to determine relative crystal misorientation

1988 ◽  
Vol 46 ◽  
pp. 830-831
Author(s):  
J. I. Bennetch
Keyword(s):  
Electron Beam ◽  
Analytical Techniques ◽  
Superplastic Forming ◽  
The Other ◽  
Kikuchi Pattern ◽  
Kikuchi Line ◽  
Line Analysis

In a recent study of the superplastic forming (SPF) behavior of certain Al-Li-X alloys, the relative misorientation between adjacent (sub)grains proved to be an important parameter. It is well established that the most accurate way to determine misorientation across boundaries is by Kikuchi line analysis. However, the SPF study required the characterization of a large number of (sub)grains in each sample to be statistically meaningful, a very time-consuming task even for comparatively rapid Kikuchi analytical techniques.In order to circumvent this problem, an alternate, even more rapid in-situ Kikuchi technique was devised, eliminating the need for the developing of negatives and any subsequent measurements on photographic plates. All that is required is a double tilt low backlash goniometer capable of tilting ± 45° in one axis and ± 30° in the other axis. The procedure is as follows. While viewing the microscope screen, one merely tilts the specimen until a standard recognizable reference Kikuchi pattern is centered, making sure, at the same time, that the focused electron beam remains on the (sub)grain in question.

Using of modified-bentonite as low-cost sorbent for removal of methylene blue dye from aqueous solution

2020 ◽  
Vol 27 (2) ◽  
pp. 45-54
Author(s):  
Saraa Muwafaq Ibrahim ◽  
Ziad T. Abd Ali
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Silanol Group ◽  
Infrared Spectrometry ◽  
Blue Dye ◽  
Ammonium Bromide ◽  
Vibration Band ◽  
Order Kinetic ◽  
Methylene Blue Dye ◽  
Modified Bentonite

Batch experiments have been studied to remove methylene blue dye (MB) from aqueous solution using modified bentonite. The modified bentonite was synthesized by replacing exchangeable calcium cations in natural bentonite with cationic surfactant cetyl trimethyl ammonium bromide (CTAB). The characteristics of modified bentonite were studied using different analysis such as Scanning electronic microscopy (SEM), Fourier transform infrared spectrometry (FTIR) and surface area. Where SEM shows the natural bentonite has a porous structure, a rough and uneven appearance with scattered and different block structure sizes, while the modified bentonite surface morphology was smooth and supplemented by a limited number of holes. On other hand, (FTIR) analysis that proved NH group aliphatic and aromatic group of MB and silanol group are responsible for the sorption of contaminate. The organic matter peaks at 2848 and 2930 cm-1 in the spectra of modified bentonite which are sharper than those of the natural bentonite were assigned to the CH2 scissor vibration band and the symmetrical CH3 stretching absorption band, respectively, also the 2930 cm-1 peak is assigned to CH stretching band. The batch study was provided the maximum removal efficiency (99.99 % MB) with a sorption capacity of 129.87 mg/g at specified conditions (100 mg/L, 25℃, pH 11 and 250rpm). The sorption isotherm data fitted well with the Freundlich isotherm model. The kinetic studies were revealed that the sorption follows a pseudo-second-order kinetic model which indicates chemisorption between sorbent and sorbate molecules.

On-site and in situ bioremediation of wood-preservative contaminated groundwater

2000 ◽  
Vol 42 (5-6) ◽  
pp. 371-376 ◽  
Author(s):  
J.A. Puhakka ◽  
K.T. Järvinen ◽  
J.H. Langwaldt ◽  
E.S. Melin ◽  
M.K. Männistö ◽  
...  
Keyword(s):  
Iron Oxidation ◽  
Wood Preservative ◽  
Pilot Scale ◽  
High Rate ◽  
Contaminated Groundwater ◽  
Groundwater Temperature ◽  
In Situ Bioremediation ◽  
Contaminated Aquifer ◽  
Fluidized Bed Process

This paper reviews ten years of research on on-site and in situ bioremediation of chlorophenol contaminated groundwater. Laboratory experiments on the development of a high-rate, fluidized-bed process resulted in a full-scale, pump-and-treat application which has operated for several years. The system operates at ambient groundwater temperature of 7 to 9°C at 2.7 d hydraulic retention time and chlorophenol removal efficiencies of 98.5 to 99.9%. The microbial ecology studies of the contaminated aquifer revealed a diverse chlorophenol-degrading community. In situ biodegradation of chlorophenols is controlled by oxygen availability, only. Laboratory and pilot-scale experiments showed the potential for in situ aquifer bioremediation with iron oxidation and precipitation as a potential problem.

Pattern Formation in the Methylene Blue-Fructose-Oxygen System in Aqueous Solution and in Gel Systems

2000 ◽  
Vol 65 (9) ◽  
pp. 1394-1402 ◽  
Author(s):  
Ľubica Adamčíková ◽  
Mária Hupková ◽  
Peter Ševčík
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Pattern Formation ◽  
Alkaline Ph ◽  
Initial Reactant ◽  
Nonlinear Reaction ◽  
Oxygen System ◽  
Hydrodynamic Processes ◽  
Liquid Layer Thickness ◽  
Catalyzed Oxidation

Spatial patterns in methylene blue-catalyzed oxidation of fructose at alkaline pH were found in aqueous solution and in gel systems. In a thin liquid layer (thickness >2.4 mm) a mixture of spots and stripes was formed by interaction of a nonlinear reaction and the Rayleigh or Maragoni instabilities. The pattern formation was affected by initial reactant concentrations and by the thickness of the reaction mixture layer. Long-lasting structures were formed in gel systems (polyacrylamide, agar, gelatin). These patterns also arise primarily from hydrodynamic processes.

scholarly journals Sulfobetaine Cryogels for Preferential Adsorption of Methyl Orange from Mixed Dye Solutions

Polymers ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 208
Author(s):  
Ramona B. J. Ihlenburg ◽  
Anne-Catherine Lehnen ◽  
Joachim Koetz ◽  
Andreas Taubert
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Methyl Orange ◽  
Dye Removal ◽  
Selective Adsorption ◽  
Water Soluble ◽  
Organic Substances ◽  
Preferential Adsorption ◽  
Dimethyl Ammonium ◽  
Dye Solutions

New cryogels for selective dye removal from aqueous solution were prepared by free radical polymerization from the highly water-soluble crosslinker N,N,N’,N’-tetramethyl-N,N’-bis(2-ethylmethacrylate)-propyl-1,3-diammonium dibromide and the sulfobetaine monomer 2-(N-3-sulfopropyl-N,N-dimethyl ammonium)ethyl methacrylate. The resulting white and opaque cryogels have micrometer sized pores with a smaller substructure. They adsorb methyl orange (MO) but not methylene blue (MB) from aqueous solution. Mixtures of MO and MB can be separated through selective adsorption of the MO to the cryogels while the MB remains in solution. The resulting cryogels are thus candidates for the removal of hazardous organic substances, as exemplified by MO and MB, from water. Clearly, it is possible that the cryogels are also potentially interesting for removal of other compounds such as pharmaceuticals or pesticides, but this must be investigated further.

Sign in / Sign up

Export Citation Format

Share Document